颞骨蜂房气化程度对血管性耳鸣的影响

为了研究颞骨蜂房气化程度与血管性耳鸣之间的生物力学关系,本文基于典型的血管性耳鸣患者的数据进行了计算分析。首先,基于血管性耳鸣患者CT图像分别建立颞骨蜂房的基础气化和过度气化2种气化程度的三维几何模型。然后,将三维几何模型分别导入Hypermesh软件中并以四面体单元进行网格划分,生成可计算的三维有限元(FE)模型。再将三维有限元模型导入Virtual.Lab Acoustics软件中,加载相同速度边界条件,计算模型的声压幅值响应。最后,以前庭处检测的声压幅值作为计算结果。由2个模型生物力学数值模拟计算的结果,可以发现频率为250 Hz时经气化模型产生的声压幅值比基础模型的值低3.02 dB。经过气化模型产生的声压幅值小于基础模型,且在相同频率下2个模型间的声压幅值差异可被血管性耳鸣患者察觉。这一结论可以尝试为临床创新治疗血管性耳鸣提供新的理论依据。      

基于损伤权重的混合多钉连接件疲劳寿命预测方法

复合材料与金属材料混合多钉连接形式是当代飞机结构中最常见的连接形式,因此对于混合多钉连接件疲劳性能的研究有助于提高对飞机结构疲劳损伤的认知。针对以Ti-6Al-4V钛合金为螺栓的ZT7H/QY9611碳纤维增强树脂基复合材料连接板与30CrMnSiNi2A金属连接板混合多钉连接结构进行数值分析和试验研究。利用有限元方法,分别对复合材料和紧固件进行疲劳损伤预测,估算复合材料连接板上螺栓孔附近的损伤,依据复合材料和紧固件的损伤量所占权重,提出了以紧固件分布和复合材料连接板铺层层数为参数的经验公式,进而有效提高混合多钉连接结构疲劳寿命的预测精度。利用试验结果将螺栓孔损伤形式进行分类讨论,探索混合多钉连接件的损伤演化方式;利用C扫描技术得到复合材料分层损伤结果,与模拟结果进行对比分析,进一步解释了模型的合理性。与试验结果对比可以看到,考虑损伤权重的寿命预测值与试验值的对数误差仅为1.1%,相对于不考虑损伤权重方法的8.4%的对数误差,该模型寿命预测精度显著提高。     

300M超高强度钢在模拟积水环境中的腐蚀行为

 针对飞机结构部件在服役过程中存在的缝隙积水导致结构材料腐蚀的问题,通过研究腐蚀产物、形貌、失重、腐蚀速率、腐蚀损伤度以及积水溶液与暴露金属的面容比、pH值等的变化,探讨了300M超高强度钢在模拟积水环境中的腐蚀行为。结果表明,300M钢在模拟积水中的腐蚀是从点蚀开始,然后点蚀坑扩展合并,逐渐发展为全面腐蚀,其腐蚀失重和腐蚀损伤度随腐蚀时间的增加而增大,腐蚀损伤度则呈现出幂函数变化趋势;随腐蚀时间的延长,模拟积水环境中的pH值从初期的4.2升到5.2再下降到4.8～5.0,平均腐蚀速率也从0.289 g/(m²·h)线性减小到0.120 g/(m²·h);电化学交流阻抗结果表明随腐蚀时间的延长,容抗弧半径逐渐增大,说明腐蚀产物对基体起到一定的保护作用,这与腐蚀速率变化规律一致;另外,不同的面容比(腐蚀介质体积与300M钢暴露面积之比)对腐蚀过程的影响是:随面容比的增加,腐蚀失重与腐蚀速率均增大。     

多体分离数值模拟及方法验证

利用自主研发的混合网格Euler／RANs方程解算软件WoF90以及六自由度动力学与运动学方程解算程序,采用脚本语言技术实现网格的自动生成,建立了一套可用于多体分离问题的准定常Euler流动非结构网格方法。通过AEDC算例对非结构准定常Euler方程方法解决多体分离问题进行了计算研究,验证了方法的可行性。     

Environmental stress level evaluation approach based on physical model and interval grey association degree

 Associating environmental stresses (ESs) with built-in test (BIT) output is an important means to help diagnose intermittent faults (IFs). Aiming at low efficiency in association of traditional time stress measurement device (TSMD), an association model is built. Thereafter, a novel approach is given to evaluate the integrated environmental stress (IES) level. Firstly, the selection principle and approach of main environmental stresses (MESs) and key characteristic parameters (KCPs) are presented based on fault mode, mechanism, and ESs analysis (FMMEA). Secondly, reference stress events (RSEs) are constructed by dividing IES into three stress levels according to its impact on faults; and then the association model between integrated environmental stress event (IESE) and BIT output is built. Thirdly, an interval grey association approach to evaluate IES level is proposed due to the interval number of IES value. Consequently, the association output can be obtained as well. Finally, a case study is presented to demonstrate the proposed approach. Results show the proposed model and approach are effective and feasible. This approach can be used to guide ESs measure, record, and association. It is well suited for on-line assistant diagnosis of faults, especially IFs.     

含腐蚀预损伤铝合金2024-T62的疲劳断裂行为及基于断裂力学的寿命预测

针对2024-T62铝合金薄板系统地开展了腐蚀预损伤对材料疲劳S-N曲线、小裂纹萌生行为、长短疲劳裂纹扩展及物理小裂纹门槛值扩展行为的影响等试验研究.结果表明:腐蚀预损伤对材料疲劳S-N曲线及材料疲劳小裂纹萌生行为有明显的影响,但时材料长短裂纹扩展及物理小裂纹门槛值扩展行为没有明显的影响.通过假定腐蚀预损伤为初始小裂纹...     

TC11焊接接头高周疲劳分形损伤模型

根据金属疲劳断口具有几何分形特征,将Chaboche高周疲劳损伤模型推广到分数维空间,建立了综合考虑断口细观特征的高周疲劳分形损伤演化模型.针对TC11钛合金电子束焊接接头,以载荷控制的疲劳试验为基础研究其高周疲劳性能;采用扫描电镜法(SEM)对断口微观特征进行定量分析,计算得到了各级载荷下疲劳断口的分形维数;通过对试...     

复合固体推进剂细观损伤扫描电镜实验及数值模拟

对复合固体推进剂进行单向拉伸载荷条件下的原位扫描电镜观察实验,分析其受载条件下的细观损伤发生及扩展特性。基于原位电镜图片,运用数字图像处理技术提取推进剂细观形貌,建立了推进剂椭圆形颗粒填充模型,对受载条件下颗粒与基体之间的脱粘行为进行数值模拟。研究表明,数值分析结果能反映推进剂受载条件下的细观损伤发生及扩展特性。     

A model of the effects of heavy ion radiation on human tissue

In heavy ion radiotherapy and space travel humans are exposed to energetic heavy ions (C, Si, Fe and others). This type of irradiation often produces more severe biological effects per unit dose than more common X-rays. A new Monte Carlo model generates a physical space with the complex geometry of human tissue or a cell culture based model of tissue, which is affected by the passage of ionizing radiation. For irradiation, the model relies on a physical code for the ion track structure; for tissues, cellular maps are derived from two- or three-dimensional confocal microscopy images using image segmentation algorithm, which defines cells as pixilated volumes. The model is used to study tissue-specific statistics of direct ion hits and the remote ion action on cells. As an application of the technique, we considered the spatial pattern of apoptotic cells after heavy ion irradiation. The pattern of apoptosis is modeled as a stochastic process, which is defined by the action cross section taken from available experimental data. To characterize the degree of apoptosis, an autocorrelation function that describes the spatial correlation of apoptotic cells is introduced. The values of the autocorrelation function demonstrate the effect of the directionality of the radiation track on the spatial arrangements of inactivated cells in tissue. This effect is intrinsic only to high linear-energy-transfer radiation.     

Recent Developments on Damage and Fracture of Thin-Walled Complex Components Produced by Spinning

The spinning technique has been widely used in the manufacture of aerospace thin-walled axisymmetric components because of its excellent formability. Damage and fracture, as the important defects that often occur and must be avoided in the forming and service stages of components, have attracted much attention of researchers. In this paper, the fracture behavior and laws of spinning components such as conical parts, tubular parts, and components with inner ribs are summarized, the typical coupled and uncoupled ductile fracture models are introduced, and their applications in spinning are analyzed. Meanwhile, the recent developments on the modified ductile fracture model in analyzing damage and fracture mechanisms of spinning are emphatically introduced. The results could provide guidance for the selection and establishment of appropriate ductile fracture models in the finite element simulation for the accurate prediction and analysis of fracture moment, location, form, damage mechanism, and evolution law, and help the development of precision spinning techniques for high-performance thin-walled complex components.