微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

纤维增韧陶瓷基复合材料的比例极限应力与残余热应力关系

从细观力学角度分析并建立了纤维增韧陶瓷基复合材料从制备温度冷却到室温过程中产生的残余热应力与复合材料的比例极限应力的关系模型。该模型表明,减少复合材料的残余热应力或提高复合材料的纤维与基体的模量比,均可提高复合材料的比例极限应力。通过单调拉伸实验测试了先驱体浸渍裂解法(PIP)制备的2D SiC/SiC复合材料的比例极限应力,并采用文中建立的比例极限应力与残余热应力关系模型,计算出复合材料SiC基体的残余热应力为-19.5 MPa。分析表明,该结果是合理的。此外,引用了公开文献报道的5种复合材料体系数据,用于验证文中所建立的比例极限应力与残余热应力关系模型的适应性和可靠性,计算结果与实验结果最大误差为18.6%,表明该模型具有较好的适应性和可靠性,可为纤维增韧陶瓷基复合材料的研究提供新思路。     

复杂电磁环境下无线接收机电磁兼容快速测试技术应用CSCD

复杂射频电磁环境下,无线接收机作为主要的敏感设备,其电磁兼容性直接影响着整个武器装备的电磁兼容特性. 本文针对GJB 151B中对于接收机非线性测试方法的局限性,引入了一种利用自动双频测试系统对接收机干扰响应的快速测试方法;并搭建了实验室半实物仿真测试平台,检测了某接收机在（ 4-6 ） GHz组合频率干扰下的所有非线性的干扰响应通道. 测试结果对于评估接收机及其所在系统的外部电磁环境适应性具有重要参考价值.     

热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

廊坊市新农村建设中的生态环境存在的问题及对策

和全国其他地方一样,廊坊市在大力推进社会主义新农村建设的过程中,也面临着农村生态环境恶化的困境。为了实现农业生产发展和农村生态环境保护之间的平衡,政府应当加大公共财政支出向农村地区倾斜的力度,坚持规划先行、服务跟进的原则,切实改善人居环境,强化农村生态环境保护法制的实施,把新农村建设成为生态良好的新农村。     

供热系统集约化运行的能耗监测及节能调节问题探讨

对我校供热系统的现状进行了分析；指出了锅炉热效率及能耗监控方面的不足，并针对锅炉热效率提高和二次网循环泵变频调节进行了节能分析计算；同时根据我校实际情况对循环泵设备配置及控制进行了分析，提出了要加强技术指标量化考核和能耗监测，提高效率、节能降耗，实现供热系统的科学化、集约化运行。