Zr-Al-(Ni-Cu)合金的非晶形成能力及热学性能

采用喷射铜模铸造法研究了Ni和Cu含量对Zr-Al-(Ni-Cu)四元合金的非晶形成能力的影响.利用X射线衍射仪分析了铸态合金的相结构,利用差示扫描量热仪研究了非晶合金的热学性能.结果表明:Zr-Al-(Ni-Cu)四元合金的非晶形成能力远大于Zr-Al-Ni和Zr-Al-Cu三元合金的非晶形成能力.Zr65Al7.5Ni10Cu17.5合金显示最高的非晶形成能力,其非晶形成临界直径可以达到7 mm.相似元素Ni和Cu在一定比例下共存,使液态合金的熵值增加,自由能降低,从而有效提高了合金的非晶形成能力.     

探空火箭图像压缩算法研究

结合探空火箭图像系统需求, 提出了一种基于小波变换编码, 即基于MSPIHT的自适应差分算术编码(MSPIHT Adaptive Differential Arithmetic Coding for image, MADAC)的图像压缩算法. 该算法对经过量化编码之后的数据 进行熵编码. 实验结果表明, MADAC算法具备探空火箭图像系统所要求的分辨 率、帧速率及压缩率可调的功能, 且易于硬件实现.      

多星联合任务规划方法

针对多星对地观测系统联合任务规划问题,考虑卫星载荷具备连续侧摆能力和多种数据压缩模式的新特点,构建了多星联合任务规划模型,在此基础上设计多星联合任务规划和数传调度算法框架,实现了卫星连续侧摆成像规划算法和基于任务优先级的数传任务调度算法,最后采用实际算例进行试验,结果表明文章提出的多星联合任务规划方法能在提高完成任务数量的同时降低卫星资源消耗,满足实际应用需求。     

月面巡视探测器动力学建模

动力学模型是研究星球探测车运动的基础。以某月面巡视探测器原理样机为背景,建立了其动力学模型,并进行了数值仿真分析。在说明月壤机械特性的基础上,结合地面车辆力学的知识,分析了松散月壤上刚性车轮的受力,考虑了主动驱动和被动驱动的情形,利用数学拟合的方法得到了满足工程要求的简化模型。在一定假设条件下,以牛顿欧拉法建立了三自由度整车动力学模型,建模时同时考虑了驱动和转向的相互影响。最后,数值仿真结果定性地验证了月面巡视探测器动力学模型的正确性。     

频率选择表面传输特性的温度循环效应

根据国家军用标准GJB 150-86对不同涂层材料和加工工艺的频率选择表面(FSS,Frequency Selective Surfaces)进行了温度循环的环境模拟试验,通过比较温度循环前后FSS的谐振频率、传输损耗、频带宽度和入射角稳定性等传输特性的差异,考察FSS在温度循环条件下的性能稳定性.结果表明,温度循环对不同材料和工艺的FSS的传输性能有较大影响,主要表现在FSS的传输损耗和频带宽度两方面.不同FSS在经过温度循环后,谐振频率下的传输损耗增大0.5~3倍,入射角越大增大的幅度越大;频带宽度增加50%~70%,不同的FSS增加的幅度不同.而对谐振频率和入射角稳定性的影响根据不同的FSS而不同,但对二者的影响都不明显.与简单振子FSS相比,组合振子FSS的传输性能受温度循环的影响较大.      

Precipitation behavior and properties of extruded 7136 aluminum alloy under different aging treatments

In this work, the mechanical properties and electrical conductivity of the extruded 7136 aluminum alloy treated by single-stage aging treatment (T6), retrogression and re-aging treatment (RRA), and multiple retrogression and re-aging treatment have been investigated by means of hardness measurements, electrical conductivity tests and tensile tests. The results have shown that the properties of the 7136 alloy such as hardness, tensile strength and electrical conductivity were sensitive to retrogression time (within 90 min). With prolonging the retrogression time, the tensile strength was enhanced first and then decreased, yet the electrical conductivity was continuously increased. The 60 min-treated alloy performed the highest tensile strength (716 MPa), whereas the 90 min-treated alloy possessed the highest electrical conductivity (33.95%IACS). Compared with the T6-treated alloy, the tensile strength and electrical conductivity were improved by 3.3% and 18.9%, respectively. The electrical conductivity showed an obvious increase with repetitious times of the RRA treatment. After 3RRA60 treatment, a good combination of tensile strength (705 MPa) and electrical conductivity (33.20%IACS) can be obtained. Compared with the T6 condition, the tensile strength and electrical conductivity were improved by 1.7% and 16.3%, respectively. The mechanism of microstructure evolution under different aging treatments has been discussed in detail.     

悬臂静子间隙影响的计算分析

悬臂静子在小型涡轮喷气和涡轴发动机的轴流压气机上广泛应用,为了探讨不同条件下悬臂静子间隙的影响,在特定的环境下,分别针对常规负荷和高负荷、小轮毂比和中等轮毂比,组合成几种不同方案,计算分析了静子根部径向间隙分别为弦长的0%、0.25%、0.5%、1%、1.5%和2%情况。计算结果表明:与叶栅中情况类似,在压气机中,悬臂静子同样存在一个特性上表现最优的最佳间隙;在根部未发生角区失速的大流量状态和设计状态,间隙的引入会使得特性恶化,在根部发生角区失速后的小流量状态,间隙的引入则能使得特性变优;间隙形成的泄漏流对角区分离的影响与间隙大小和角区分离程度相关;压气机设计状态负荷水平减小后,间隙的影响规律基本不变;轮毂比增大后,最佳间隙值有减小的趋势。     

含硅芳炔树脂改性氰酸酯树脂的性能

将双酚E型氰酸酯(BEDCy)与含硅芳炔树脂(PSA)用溶液共混的方法制备了共混树脂(BEDCy/PSA);通过DSC和原位红外研究了共混树脂的固化反应,使用TGA和DMA表征了树脂的耐热性能;还考察了共混树脂的介电性能和力学性能.结果表明,PSA树脂能够降低BEDCy树脂的固化温度;随着PSA树脂的添加,氮气和空气氛...     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.