Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

Sc在L10-TiAl金属间化合物中占位的理论研究

基于密度泛函理论,运用第一原理赝势平面波方法,采用CASTEP量子力学能量软件包研究了Sc占据Ti位与Sc占据A l位的超胞晶格常数、原子形成热、超胞总态密度与电子密度差分图,两种情况对比下,在L10-TiA l合金中,Sc优先占据Ti位,这一结论为进一步研究三元系TiA l-Sc合金提供了理论研究的基础。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

High Excitation ISM and Gas

An overview is given of ISO results on regions of high excitation ISM and gas, i.e. HII regions, the Galactic Centre and Supernova Remnants. IR emission due to fine-structure lines, molecular hydrogen, silicates, polycyclic aromatic hydrocarbons and dust are summarised, their diagnostic capabilities illustrated and their implications highlighted. Based on observations with ISO, an ESA project with instruments funded by ESA Member States (especially the PI countries: France, Germany, The Netherlands, and the United Kingdom), and with the participation of ISAS and NASA.     

300M钢纯洁度磁粉检验磁痕现象的分析

采用交、直流磁粉检验并结合金相试验、电子探针试验及微量元素含量分析的方法，对３００Ｍ钢磁痕现象的本质进行了分析。结果表明，采用磁粉检验方法对航空优质钢进行纯洁度检验是可信的。     

国家财政主要支出项目与各项税收收入的最优化--回归分析在最优化中的应用研究实例

利用回归分析方法得到国家财政部分主要支出项目，部分税收收入与国内生产总值构成的回归方程，由此构成线性规划问题的约束方程组。再用M单纯形法求最优解。     

L8飞机从风洞到飞行的抖振相关性研究

介绍了Ｌ８飞机抖振边界修正结果，并与同类飞机Ｌ２９飞行抖振边界进行了比较；给出了Ｌ８飞机抖振边和轻度抖振边界预测值。同时将预测抖振边界和试飞得到的抖振边界作了比较。     

M40J和T300碳纤维的微结构

利用SEM、TEM、XPS、XRD、Raman和元素分析仪分析了M40J和T300的表面化学、物理及微观结构特征.研究发现:M40J含碳量高于T300纤维,而含氮量低于T300纤维,且表面活性基团比T300纤维低;M40J和T300碳纤维表面具有大量沟槽,前者相对长而浅,后者相对短而深;T300纤维端面皮芯结构明显,而M40J端面结构较均匀;M40J的微晶结构及取向性优于T300碳纤维.     

基于公务机经济性的升阻特性优化

以提高公务机空气动力效率为目的,讨论了可应用于工程实际的升阻优化技术的优缺点,并展望了其应用前景。     

316L 不锈钢的单轴棘轮效应

对316L不锈钢进行了单轴应变控制和应力控制下的系统循环试验。对316L不锈钢在应变循环下的循环应变幅值、应变幅值历史、平均应变对循环特性的影响进行了揭示;对该材料在应力循环下的应力幅值、平均应力及其历史对循环蠕变（棘轮效应）的影响进行了分析。发现无论单轴应变循环特性还是非对称单轴应力下的棘轮效应不但依赖于当前加载状态,而且依赖于其加载历史。得到了316L单轴循环行为的一些有意义的结果。