空间目标双基地ISAR一维距离像速度补偿方法

空间目标的高速运动会造成双基地ISAR一维距离像的畸变,针对此问题,研究了相应的速度估计与补偿方法。基于中频直接采样匹配滤波非相参双基地ISAR成像系统,首先研究了高速运动对双基地ISAR成像的影响,其次利用雷达基带回波具有的稀疏性,构造出与高速运动目标回波特性相匹配的冗余基并对其进行稀疏分解,然后据此估计出回波的调频斜率,进而估计出目标的无模糊速度,最后构造补偿相位项完成对宽带回波的速度补偿。算法补偿精度高,且无测速模糊,空间目标理想散点的仿真实验验证了补偿方法的有效性。     

基于距离像特征的复合速度估计算法研究

首先分析了步进频率宽带信号混频处理原理和目标速度对距离像的影响。在此基础上,提出了基于距离像熵和距离像对比度的速度估计算法,详细分析了这两种算法的数学原理、步骤、效果、适用条件等。最后,基于这两种算法又提出了复合速度估计算法,大大提高了速度估计精度。     

不同型线结构船艏表面压力特性对比实验研究

为优选船艏结构型线方案,在风洞中针对三个在结构型线上仅有细微差别的船艏方案进行表面压力特性对比测试。实验获得了各型线方案模型表面压力空间分布特性和压力脉动特性,并通过表面压力特性的综合对比进行了结构型线评估,为船艏的结构型线设计提供直接的技术依据。     

Numerical prediction and wind tunnel experiment for a pitching unmanned combat air vehicle

The low-speed flowfield for a generic unmanned combat air vehicle (UCAV) is investigated both experimentally and numerically. A wind tunnel experiment was conducted with the Boeing 1301 UCAV at a variety of angles of attack up to 70 degrees, both statically and with various frequencies of pitch oscillation (0.5, 1.0, and 2.0 Hz). In addition, pitching was performed about three longitudinal locations on the configuration (the nose, 35% MAC, and the tail). Solutions to the unsteady, laminar, compressible Navier–Stokes equations were obtained on an unstructured mesh to match results from the static and dynamic experiments. The computational results are compared with experimental results for both static and pitching cases. Details about the flowfield, including vortex formation and interaction, are shown and discussed, including the non-linear aerodynamic characteristics of the vehicle.     

Radial profile measurements of the solar wind speed using radio sounding techniques

Velocity measurements of the solar wind in the region of its acceleration were carried out in 1984 with Venera Orbiters using the following specific radio sounding techniques: (i) phase and frequency correlations from two or three widely-spaced ground stations; (ii) phase and frequency correlations from two spacecraft and two widely-spaced ground stations; (iii) two station two-way coherent Doppler measurements; (iv) determination of the break frequency in power spectra of intensity fluctuations. Our results are substantially lower than those derived from direct Doppler shift measurements of transition region and lower coronal resonance lines and those from measurements applying the Doppler dimming technique.     

一种测定大值的风速计

简单叙述了研制1种大风速值简易精密测量仪器原理和方法，并对测量误差进行了估算。     

考虑重力的风机叶片水平加载测试方法

在风电叶片三维有限元参数模型中引入了重力产生的附加载荷,仿真计算了风电叶片水平加载方式的静载荷测试中附加载荷产生的水平方向的耦合位移,分析了耦合位移对测试过程中理论计算结果的影响;由于重力的叠加效应,测试中某些截面实际施加的等效载荷可能远超叶片设计的目标测试载荷,建议联合有限元分析,优化叶片安装角度和加载力方向的方法,降低叶片局部截面实际施加等效载荷的过载峰值。     

中纬突发E层特性的模拟分析

从基本的连续性方程出发，并结合运动方程，运用特征线方法求解，在合理的动力学假设条件下，模拟金属离子的汇聚，即Es层的形成．模拟的结果在一定程度上证实了风剪切理论的合理性．通过改变风场和电场模式的输入参量，使模拟的结果体现出不同当地时、不同季节的金属离子汇聚情况，讨论了模拟Es层峰值密度对风场和电场的周日和季节变化的响应，其结果与统计得到的Es层出现率的时间分布特征相似．     

Remote-controlled flexible pose measurement system and method for a moving target in wind tunnel

The measurement of position and attitude parameters for the isolated target from a high-speed aircraft is a great challenge in the field of wind tunnel simulation technology. This paper proposes a remote-controlled flexible pose measurement system in wind tunnel conditions for the separation of a target from an aircraft. The position and attitude parameters of a moving object are obtained by utilizing a single camera with a focal length and camera orientation that can be changed based on different measurement conditions. Using this proposed system and method, both the flexibility and efficiency of the pose measurement system can be enhanced in wind tunnel conditions to meet the measurement requirements of different objects and experiments, which is also useful for the development of an intelligent position and attitude measurement system. The position and the focal length of the camera also can be controlled remotely during measurements to enlarge both the vertical and horizontal measurement range of this system. Experiments are conducted in the laboratory to measure the position and attitude of moving objects with high flexibility and efficiency, and the measurement precision of the measurement system is also verified through experiments.     

非圆等距型面轮廓X-C轴联动高速磨削试验北大核心CSCD

针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。