转子振动波德图的计算机辅助测试与分析系统

介绍了一种利用高性能数据采集卡及定时 /计数器卡对转子振动波德图进行测试与分析的系统。详细说明了系统的硬件结构及软件编制原理 ,并使用自行开发的Windows应用软件对一模拟转子系统进行了实验研究     

航天器宽带随机振动响应分析

简要概述了航天器宽带随机振动试验和分析的必要性以及国内外预示技术的发展与现状；然后以某卫星为例，利用有限元方法和统计能量分析（SEA）对整星的宽带随机振动学环境进行了预示，经过与试验结果的对比，验证了上述方法的可行性。     

用于大型运载器模态试验的油气支承系统

本文主要讨论运载器模态试验对支承系统的要求,油气支承系统的分析模型,此外文中给有系统功能试验结果和应用实例.最后,对大型运载器模态试验支承系统的发展提出了基本设想和建议.     

基于单CPU的通用微机冲击振动控制技术

基于单ＣＰＵ的通用微机冲击振控制技术的独到之处在于，冲击驱动信息的生成、修正以及冲击响应信号的采样、分析等操作均由微机软件进行控制。主要介绍实现该技术的软件设计原理，并给出相应控制实验结果。     

空间可展结构非线性动力学特性实验研究

由于可展结构在运动过程中的时变性，特别是干扰所引起的非线性动力学特性，涉及许多深层次尚在探讨的动力学问题。为了考察间隙非线性对系统动力学性能的影响，本文对空间可展结构进行了动力学实验研究。实验结果表明理想结构与实验结构存在较大差异，铰接间隙等非理想机械因素导致系统复杂的非线性动力学行为，使系统的动力学性能下降。     

Parametric instability of twisted cross-ply laminated panels

The present paper deals with the study of the vibration, buckling and parametric instability characteristics of general laminated cross-ply pre-twisted cantilever flat and curved panels. The effects of angles of pre-twist, aspect ratio, static load factor, and the lamination parameters of the cross-ply twisted curved panels on the principal instability regions are studied using Bolotin?s approach. An eight-noded isoparametric quadratic shell element with five degrees of freedom per node is used to develop the finite element procedure. The first order shear deformation theory is used to model the twisted cross-ply curved panels considering the effects of transverse shear deformation and rotary inertia. The linear part of the strain is used to derive the elastic stiffness matrix and the non-linear part of the strain is used to derive the geometric stiffness matrix. The global matrices are obtained by assembling the corresponding element matrices using skyline technique. Subspace iteration method is used throughout to solve the eigenvalue problem. Reduced integration technique is adopted in order to avoid possible shear locking. Based on the parametric studies, it is found that the instability behavior of twisted cross-ply cantilever panels is greatly influenced by the geometry, material, angle of twist and lamination parameters. So, this can be used to advantage in tailoring during design of crossply twisted cantilever panels.     

强非线性自由振动问题的一种解法

本文用改进了的L－P法研究了一类保守系统强非线性自由振动问题；在此基础上，用插值摄动法[1]进一步研究了更一般的非保守系统的自由振动问题。算例表明，本文方法是可靠的。     

导弹垂直发射装置对燃气流压强周期性振荡的响应

本文对舰载导弹垂直发射装置中的燃气流周期性振荡特性进行了分析与实验测量，对装置产生的响应特性也进行了实验研究和有限元分析。实验测量结果与理论计算在规律上有定性的一致     

Design and experiments of an active isolator for satellite micro-vibration

In this paper, a soft active isolator（SAI） derived from a voice coil motor is studied to determine its abilities as a micro-vibration isolation device for sensitive satellite payloads. Firstly,the two most important parts of the SAI, the mechanical unit and the low-noise driver, are designed and manufactured. Then, a rigid-flexible coupling dynamic model of the SAI is built, and a dynamic analysis is conducted. Furthermore, a controller with a sky-hook damper is designed. Finally,results from the performance tests of the mechanical/electronic parts and the isolation experiments are presented. The SAI attenuations are found to be more than 20 d B above 5 Hz, and the control effect is stable.     

Vibration coupling effects and machining behavior of ultrasonic vibration plate device for creep-feed grinding of Inconel 718 nickel-based superalloy

Ultrasonic vibration-assisted grinding(UVAG) is an effective and promising method for machining of hard-to-cut materials. This article proposed an ultrasonic vibration plate device enabling the longitudinal full-wave and transverse half-wave(L2T1) vibration mode for UVAG.The characteristics of two-dimensional coupled vibration in different directions were analyzed on the basis of apparent elastic method and finite element method. Furthermore, a correction factor was applied to correct the freque...