速率捷联制导系统工具误差分析方法

本文首先介绍速率捷联制导系统工具误差分析的主要内容,接着使用一种新的方法建立了数学模型,并通过一个范例进行了数学仿直.仿真结果证明,本文提出的算法是可信的.     

俄制引进装备中数字板件国产化研制替代的探讨

针对维修中俄制引进地空导弹武器系统国产化数字板件替代装备联调过程中出现的延时累计误差“瓶颈”问题，分析研究了具体解决办法和措施，并通过了武器系统实弹打靶检验。     

基于双量程推力传感器的精确测力技术

针对双量程推力传感器在使用中测试精度低的问题,结合传感器固有特性,开展了传感器动态特性分析及误差补偿方法的研究。通过有限元分析和力锤冲击试验,结合结构分析获得了双量程力传感器等效二自由度和三自由度动力学模型。利用近似求积数值法对冲击力试验输出信号进行补偿,获得了接近标准信号的测试结果,对该补偿方法进行了有效性验证。结果显示:本方法对发动机试验的推力信号进行了补偿,推动了单室双推力发动机推力的精确测量,为双推力发动机的推力测试提供了有效途径。     

垂直度误差对复合材料单钉连接性能的影响

为揭示连接孔垂直度误差对航空复合材料连接性能的影响规律,对准各向同性碳纤维环氧树脂复合材料板进行了单钉单剪试验研究。以极限承载强度、弦刚度、2%偏移承载强度为指标研究连接孔的倾斜角度、倾斜方向以及螺栓扭矩对接头承载性能的影响规律。试验结果表明:当连接孔倾斜角度从0°增加到4°时,接头弦刚度增大10%~40%,极限承载强度下降9%~12%;连接孔倾斜方向对极限承载强度影响甚微,却可使接头弦刚度产生20%~30%的变化;增加螺栓扭矩可以有效提高极限承载强度,但对接头刚度无明显影响;连接孔倾斜角度越大,则螺栓扭矩的增大对2%偏移承载强度的强化效果越不明显。     

权值动态分配的加权平均法在姿态解算中的应用

鉴于各种姿态算法解算后的精度不高,提出将加权平均法应用于捷联惯导系统的姿态解算中.针对实际应用中无法准确获得姿态角度的真实值这一情况,提出对解算误差进行实时估计的方法,再基于最优权值分配的原则进行权值动态分配.对几种姿态解算算法进行了有效的融合,并应用到姿态解算模块的实际测量中.测量结果分析表明此种方法很大程度上减少了单一算法的解算误差及测量的误差,提高了测量的精度.     

Azimuth selection for sea level measurements using geodetic GPS receivers

Based on analysis of Global Positioning System (GPS) multipath signals recorded by a geodetic GPS receiver, GPS Reflectometry (GPS-R) has demonstrated unique advantages in relation to sea level monitoring. Founded on multipath reflectometry theory, sea level changes can be measured by GPS-R through spectral analysis of recorded signal-to-noise ratio data. However, prior to estimating multipath parameters, it is necessary to define azimuth and elevation angle mask to ensure the reflecting zones are on water. Here, a method is presented to address azimuth selection, a topic currently under active development in the field of GPS-R. Data from three test sites: the Kachemak Bay GPS site PBAY in Alaska (USA), Friday Harbor GPS site SC02 in the San Juan Islands (USA), and Brest Harbor GPS site BRST in Brest (France) are analyzed. These sites are located in different multipath environments, from a rural coastal area to a busy harbor, and they experience different tidal ranges. Estimates by the GPS tide gauges at azimuths selected by the presented method are compared with measurements from physical tide gauges and acceptable correspondence found for all three sites.     

圆筒形拉伸冲压零件下料公式的修正方法

在冲压拉伸制造薄板形零件的模具设计制造中,通常都是先利用公式计算出落料尺寸,根据这个尺寸制造出落料凸模和落料凹模,试生产后再根据制件的误差对落料凸模和落料凹模进行修改,如果成本高,效率低,就通过探讨误差生成的原因以及做出应对的修正方法,从缩小误差,提高试生产效率方面考虑,设法缩短试制时间。     

A novel environmental control system based on membrane dehumidification

This paper conducts a simulation study of a novel aircraft environmental control system based on membrane dehumidification(MD-ECS),and compares the system with the up-to-date four-wheel high pressure de-water system(4WHPDW-ECS).Mathematical models for the two systems are established,and a system simulation using a numerical technique is performed to analyze and compare the cooling performance of the two systems.Simulation results show that the cooling capacity of MD-ECS is much higher than that of 4WHPDW-ECS under the same working conditions,indicating that the novel system is theoretically feasible and promising.The effects of the sweep ratio of the membrane dehumidifier on the dehumidification and cooling performance of the system is also investigated.     

钛合金蜂窝三层结构的扩散焊接研究

介绍了俄罗斯钛合金蜂窝三层结构扩散焊接的研究成果.详细介绍了铝合金、焊接规范选择、接头应力变形状态的分析、模拟计算等,有助于国内钛合金的焊接研究.     

凸轮轴的检测与数据处理

对凸轮轴的检测内容，凸轮检测位置的确定，检测起始转角的求解，升程的检测方法以及检测数据的处理等方面进行了较系统的分析．