全文获取类型
收费全文 | 141篇 |
免费 | 24篇 |
国内免费 | 62篇 |
专业分类
航空 | 179篇 |
航天技术 | 10篇 |
综合类 | 33篇 |
航天 | 5篇 |
出版年
2023年 | 4篇 |
2022年 | 14篇 |
2021年 | 14篇 |
2020年 | 3篇 |
2019年 | 12篇 |
2018年 | 7篇 |
2017年 | 9篇 |
2016年 | 16篇 |
2015年 | 8篇 |
2014年 | 14篇 |
2013年 | 4篇 |
2012年 | 7篇 |
2011年 | 8篇 |
2010年 | 5篇 |
2009年 | 5篇 |
2008年 | 5篇 |
2007年 | 8篇 |
2006年 | 9篇 |
2005年 | 8篇 |
2004年 | 5篇 |
2003年 | 1篇 |
2002年 | 3篇 |
2001年 | 9篇 |
2000年 | 6篇 |
1999年 | 7篇 |
1998年 | 7篇 |
1997年 | 6篇 |
1996年 | 3篇 |
1994年 | 4篇 |
1993年 | 7篇 |
1992年 | 3篇 |
1991年 | 3篇 |
1990年 | 1篇 |
1989年 | 2篇 |
排序方式: 共有227条查询结果,搜索用时 0 毫秒
1.
A synchronous control of relative attitude and position is required in separated ultra-quiet spacecraft, such as drag-free, disturbance-free, and distributed spacecraft. Thus, a twistor-based synchronous sliding mode control is investigated in this paper to solve the control problem of relative attitude and position among separated spacecraft modules. The twistor-based control design and the stability proof are implemented using the Modified Rodrigues Parameter (MRP). To evaluate the effectiveness of the proposed control method, this paper presents a case study of separated spacecraft flying control considering the mass uncertainty and external disturbances. In addition, a simulation study of the Proportional-Derivative (PD) control is also presented for comparison. The results indicate that the twistor-based sliding mode controller can ensure global asymptotic stability. The states converge fast with ultra-precision and ultra-stability in both the attitude and position. Moreover, the proposed twistor-based sliding mode control system is robust to the mass uncertainty and external disturbances. 相似文献
2.
进行了Ti6A14V合金锆刚玉页轮和碳化硅页轮的磨削性能试验研究,分析了磨削用量对磨削力、磨削温度和磨削表面完整性的影响。磨削力通过KISTLER9265B测力仪测定,磨削表面温度由NIUSB-621X信号采集系统测得,磨削表面形貌和金相组织由HiroxKH-7700型体视显微仪和Quanta200型扫描电镜(SEM)观察,表面粗糙度由Mahr Perthometer M1粗糙度仪测得,表层显微硬度通过HVS—1000硬度计测定。研究结果表明:页轮磨削钛合金工件表面没有发生烧伤现象,磨削热影响区厚度小于50μm,锆刚玉页轮比碳化硅页轮更适合干式磨削钛合金。 相似文献
3.
根据磁悬浮零部件专用测量机气浮运动组件内外球面的高精度技术要求,设计一种角摆静压力自动补偿万向球头节研磨机构,在普通车床上采用内外球面自动研磨的方法代替传统手工对研.实践证明提高了气浮运动组件的研磨质量和效率,有一定参考价值. 相似文献
4.
钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜(SEM)、能谱(EDS)、X射线衍射(XRD)、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明:低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。 相似文献
5.
介绍了采用碟形砂轮磨削面齿轮的原理及过程,研究了齿廓包络和齿宽包络两种包络方式产生包络残差的机理.分别建立了两种加工方式下包络残差的计算模型和方法,并研究了所产生包络残差的特点.通过数值算例分析了包络过程中刀具周向进给角度、齿宽方向进给量以及碟形砂轮外径对齿面包络残差的影响规律.计算结果表明:齿宽包络比齿廓包络具有更高的效率.进行了以齿廓包络方式的面齿轮磨齿加工实验,当刀具周向进给角度分别取为2°,1°,0.5°及0.2°时,齿面表面粗糙度逐渐明显提高,齿面磨削加工印痕的数目和方向与包络仿真计算结果一致.初步证明根据包络残差计算结果选取合适的进给量参数,可以保证面齿轮磨齿加工的表面粗糙度水平并能提高加工效率. 相似文献
多头环面蜗轮滚刀通常采用螺旋槽,以降低刀齿负前角的绝对值、并均衡每个刀齿左右两侧的前角,从而提高滚刀的切削性能。由于环面蜗轮滚刀螺旋线上各处的螺旋升角不同,所以各个刀齿左右两侧的前角均衡问题更为复杂,鲜有螺旋槽前刀面的精确成形方法的研究。基于环面蜗杆专用数控机床,提出采用双锥砂轮磨削螺旋槽环面蜗轮滚刀前刀面的方法,根据齿轮啮合理论,建立由双锥产形面展成平面二次包络环面蜗轮滚刀螺旋槽前刀面的数学模型,给出每个刀齿两侧在分度环面螺旋线上的前角计算公式。算例计算结果表明:如果采用直槽滚刀,对应的前角在-19.530 3°~19.530 4°;通过合理的参数选择,可使得螺旋槽滚刀对应的前角在-8.1°~7.3°,有效减小了刀齿负前角的绝对值。对环面蜗轮滚刀螺旋槽进行仿真加工,并且在仿真软件中对前角进行测量,测量结果与计算结果相吻合,证明本文方法的正确性。 相似文献
7.
8.
9.
《中国航空学报》2021,34(2):576-585
Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles. 相似文献
10.
针对非圆等距型面轮廓磨削加工存在表面质量差的问题,建立基于恒磨除率X-C轴联动磨削理论模型。选用陶瓷CBN砂轮进行三弧段非圆等距型面轮廓的高速磨削正交试验,探究砂轮线速度、工件速度和磨削深度对磨削比能、切向磨削力、磨削温度、表面粗糙度的影响规律。分析表明,砂轮线速度对切向磨削力、表面形貌的影响最大,磨削深度对磨削比能、磨削温度、表面粗糙度的影响最大。进行表面形貌观测未探测到明显的磨削烧伤区域,证明恒磨除率X-C轴联动磨削方式可用于非圆等距型面轮廓磨削加工。 相似文献