Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

考虑滑流影响的埋入式进气道气动特性分析与流动控制研究

研究滑流对埋入式进气道性能的影响机理对于发动机的稳定性具有重要意义。针对某型涡桨发动机 滑油散热器进排气道系统,基于 CFD技术建立系统的螺旋桨滑流与滑油散热器内流一体化数值模拟方法,进 行考虑滑流影响的滑油散热系统埋入式进气道气动设计仿真分析;针对埋入式进气道由于吸入边界层低能气 流导致通过散热器流量低的问题,设计4组涡流发生器进行主动流动控制。结果表明:滑流使得进气道中的气 流偏离,难以形成稳定漩涡,容易发生流动分离;而合理设计的涡流发生器可以有效改善埋入式进气道内流场 特性,并使通过散热器的流量提高12%。     

亚声速叶片与跨声速叶片的气动阻尼比较

为了研究叶轮机中叶片与流场流固耦合作用情况下的气动阻尼,分别以亚声速和跨声速转子叶片为例计算气动阻尼。根据对非定常气动力的分析,提出了一种与结构等效粘滞阻尼比对应的模态气动等效粘滞阻尼比的定义。采用弱耦合分域求解的算法,在线性范围内,计算并比较了跨声速叶片和亚声速叶片模态和振幅对模态气动阻尼比的影响,根据分布气动阻尼比研究压缩波对模态气动阻尼比的影响。研究结果表明这两类叶片的气动阻尼特性基本一致,所提参数对两类叶片的气动阻尼的影响基本相同。     

二维超燃冲压发动机磁控进气道的数值模拟

针对飞行马赫数大于设计马赫数的情况,采用二维磁流体动力学方程对磁控进气道进行了数值模拟研究。数值模拟结果表明磁流体装置的电磁作用可以使非设计马赫数下进气道激波满足SOL(shock on lip)条件,并使出口处的流动变得均匀。分析了磁流体作用位置、宽度和深度等关键控制参数对该类进气道性能的影响,计算结果表明,磁流体作用区域越靠近飞行器前缘,而且在纵向越深,则进气道出口处的流动越均匀,但流率会有所下降;若磁流体作用区域较宽,则需较小的磁场就能使非设计马赫数下进气道的激波结构满足SOL条件。     

弹用S弯进气道气动性能试验

对一种弹用S弯进气道进行了试验,结果表明:①偏航角一定,攻角由负到正变化时,总压恢复系数先上升后变化不大,|DC₆₀|则先下降后小幅升高;②攻角一定,总压恢复系数和|DC₆₀|随偏航角的增加均呈先升高后降低的趋势;③大的攻角和偏航角组合状态下,总压恢复系数较低,|DC₆₀|偏大,但随偏航角进一步增大,进气道性能有所改善;④进/发匹配点处,进气道出口压力功率频谱较平坦且对姿态角和来流马赫数的变化均不敏感;⑤发动机小流量状态时,进气道模型发生了喘振,频率约为150 Hz.      

故障树分析在某APU进气门故障诊断中的应用

首先介绍了故障树分析方法的概念和原理,然后以某辅助动力装置（APU）进气门组件为例．在对系统故障现象进行分析判断的基础上,按照任务和功能关系,建立包含各功能单元的故障树模型。随后求得系统的最小割集,并计算出底事件的重要度,并以此为依据,从大到小排序,确定故障诊断的最优程序。实验结果表明,所用方法具有较强的故障诊断能力,能进行准确的故障定位,并能给出相应的故障处理措施,为该辅助动力装置故障诊断的发展提供了较为实用的参考价值。     

宽马赫数范围高超声速进气道转动唇口变几何方案研究

结合简单一维流理论讨论了一种工作于Ma=4～7、采用可转动唇口的变几何二元高超声速进气道设计方案,并利用数值仿真手段对其Ma=4下的自起动性能及其他不同工作马赫数下的性能进行了研究.结果表明:所设计的变几何进气道必须辅以附面层排移措施才能在Ma=4下顺利实现自起动;该变几何方案Ma=4下的流量系数达0.7以上,这为飞行器加速提供了强有力保障;与定几何进气道相比,变几何进气道高低马赫数下的总体性能均得到显著提高;此外,转动唇口的铰接位置对自起动性能有重要影响.      

着陆襟翼打开状态下抓斗式反推装置 三维流动数值模拟

基于求解三维Reynolds-averaged Navier-Stokes方程,数值模拟了着陆襟翼打开状态下抓斗式反推装置工作时流场分布特性.网格采用非结构化四面体与六面体混合分区生成技术,湍流模型选用Spalart-Allmaras模型.结果表明,在计算滑跑速度范围内,反向排气流不会被进气道重新吸入;高温反向排气流会冲击到飞机吊挂及部分机翼,需引起注意;随着滑跑速度的降低,反向排气流侧向影响范围急剧增大,若机翼后掠角较大,则反向排气流容易被相邻发动机再次吸入,引起进气畸变;当滑跑速度降低到34m/s时,反向流开始吹向地面,可能会卷起地面颗粒物并且被进气道吸入;随着滑跑速度的降低,反推力减小.