机内测试虚警分析和控制

现代飞行器广泛采用机内测试(Built-intest,BIT)技术,以便对其内部故障进行自动检测、诊断和隔离,但是常规BIT面临诊断能力不足和诊断模糊性等问题,导致BIT虚警率高,难以有效发挥其应有的作用.本文论述了BIT虚警的基本理论、虚警的危害及现状,并从BIT虚警产生的原因分析入手,提出了解决虚警问题的一些方法和措施.     

基于网络化测试技术的通信装备维修保障

未来信息化战争条件下,通信装备朝着网络化、标准化、通用化、系列化、模块化的方向发展,首先在分析现有通信装备维修保障中存在的问题和不足的基础上,提出了应用网络化测试技术的意义,并给出了系统的总体结构和两种软件设计方法;然后对现有通信装备的网络化改造提出了通过连接PC机间接接入,通过接口转换模块接入,现场智能设备嵌入TCP/IP协议三种方式,并对他们进行了分析.     

单片机在航箭发控系统通用检测仪中的应用

目前航空火箭武器仍是歼击机上主要对地攻击武器之一.但现有的航箭发控系统检测仪既不具有通用性,又不能测试航箭发射脉冲参数.为此,利用单片机技术设计了航箭发控系统通用检测仪.介绍了检测仪的设计方法,给出了较为详细的硬件组成和软件流程.该仪器现已装备部队,经使用证明,该检测仪操作简单、显示直观、清晰、记录准确、通用性强、满足设计.     

自动测试系统适配器自动设计技术

 针对当前自动测试系统（ATS）适配器设计中存在的“自动化程度较低、缺乏通用性”的不足,开发了ATS通用适配器自动设计技术。建立了一整套通用适配器自动设计流程,在依次完成通用端口设计、UUT测点资源匹配、适配器开关网络设计、相关工程设计后即可实现自动设计一个通用适配器的目的。以某机载通讯设备自动测试系统为例,采用该技术可缩短ATS适配器开发周期至原来的1/3,降低开发成本,提高设计的标准化、通用化程度,适配器需要量由5个减为1个。     

基于MSC/PATRAN的飞机结构强度静力试验数据实时跟踪与处理系统开发

 在Windows环境下,以MSC/PATRAN为平台,利用平台提供的二次开发语言PCL(Patran Command Language),并结合C++语言,通过客户化、增设特定的命令和窗体等技术开发了飞机结构强度静力试验数据实时跟踪与处理系统TestDTAS（Test Data Tracking, Analyzing and Processing System）。在结构试验进行中,TestDTAS可以实时地监测结构试验件中应力和位移的变化情况,并与理论分析结果进行对比,而在试验结束后,TestDTAS可以进行试验数据回放和分析,从而将试验与理论分析有机的结合在一起,对结构静力试验和结构设计有很高的实用价值。     

New Cutting Force Modeling Approach for Flat End Mill

A new mechanistic cutting force model for flat end milling using the instantaneous cutting force coefficients is proposed. An in-depth analysis shows that the total cutting forces can be separated into two terms: a nominal component independent of the runout and a perturbation component induced by the runout. The instantaneous value of the nominal component is used to calibrate the cutting force coefficients. With the help of the perturbation component and the cutting force coefficients obtained above, the cutter runout is identified. Based on simulation and experimental results, the validity of the identification approach is demonstrated. The advantage of the proposed method lies in that the calibration performed with data of one cutting test under a specific regime can be applied for a great range of cutting conditions.     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

环模设备研制用玻璃钢的放气性能研究

文章介绍了在环模设备研制中采用玻璃钢材料制作真空容器的发展需求,为满足设计要求,对玻璃钢复合材料的放气性能进行研究。文中阐述了材料的放气机理和不同测试方法,以及对材料样品的放气性能的测试过程,并获得了重要数据。这项研究工作为真空系统设计提供了参考依据,也为非金属材料环模设备研制提供了思路。     

航天ATS快速测试体系结构研究

快速发射是未来空间信息作战和导弹武器发展面临的新课题,快速测试是快速发射的重要环节。航天ATS快速测试需要遵循一定的体系结构而发展。以国际通用测试系统体系结构为背景,结合我国航天测试的需求,提出了航天ATS快速测试体系结构,分析了航天ATS快速测试的测试流程并行化、关键参数连续监测化和测试数据处理快速化等目标,以及所涉及到的图形化程序开发、仪器可互换等关键技术。结论有利于促进航天ATS快速测试技术的进步,并为其发展提供参考。