运动油滴/固体壁面斜碰撞的状态辨识及特征分析

 航空发动机轴承腔油气两相流动与换热研究是轴承腔润滑与换热设计的重要基础工作,而运动油滴与轴承腔壁面的碰撞状态辨识及特征分析是轴承腔油气两相流动与换热研究的组成部分。基于VOF方法建立了运动油滴与固体壁面斜碰撞数值仿真模型,实现了运动油滴与固体壁面斜碰撞状态的数值模拟,分析了碰撞油滴直径、入射角和碰撞速度对沉积油膜铺展长度、油膜堆积厚度和溅射油滴数目等碰撞状态特征参数的影响规律,提出了运动油滴与固体壁面斜碰撞条件下的状态判断准则,并得到了文献的物理试验工作的支持。研究结果表明:随着油滴入射角减小,沉积油膜铺展长度和油膜堆积厚度增大,溅射油滴数目减少;随着碰撞速度和油滴直径的增大,沉积油膜铺展长度和溅射油滴数目均增大,但油膜堆积厚度对应前者呈减小趋势、对应后者仍呈增大趋势。     

自旋火箭姿态运动的稳定性分析和数学仿真

本文主要对自旋火箭姿态运动的稳定性进行了分析,并给出了数学仿真结果。飞行试验结果表明,稳定性分析和数学仿真是正确、可靠的。     

Effects of yaw-roll coupling ratio on the lateral-directional departure prediction and restraint

The experimental data obtained from yaw-roll coupled wind tunnel tests are used for lateral-directional departure prediction, by linearizing the_b model to extract nominal dynamic derivatives at each coupling ratio.The prediction results are compared with those of the existing engineering methods which are based on the conventional aerodynamic derivatives.The comparison shows that the yaw-roll coupling ratio has a great influence on the departure susceptibility.The departure resistance will loss in partial region of the coupling ratio when the angle of attack is higher than a critical value.According to the stable and unstable regions of coupling ratio, a two-segment stability augmentation system with two different feedback gain matrices is obtained by pole-placement method.The two-segment stability augmentation system is used in the simulations of straight and level flight, steady turn, spin recovery and Herbst maneuver.The simulation results are also compared with the applications of a fixed-gain stability augmentation system designed by the conventional aerodynamic derivatives.When the yaw-roll coupling effects are fully considered, the two-segment stability augmentation system is more effective for departure restraint and can provide a better flying quality with less control energy.     

机载风切变系统告警准则研究

根据风切变对飞机飞行影响的机理,以及FAA对CATⅠ类着陆最坏条件下的边界要求,推导了风切变的危险程度判据。通过计算,分析了垂直风切变与水平风切变对飞行性能的影响的异同,并通过对危险判据与性能恶化参数的相关性研究,提出了适用于机载风切变探测告警系统的告警准则。     

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

Event-triggered attitude control of spacecraft

The problem of spacecraft attitude stabilization control system with limited communication and external disturbances is investigated based on an event-triggered control scheme. In the proposed scheme, information of attitude and control torque only need to be transmitted at some discrete triggered times when a defined measurement error exceeds a state-dependent threshold. The proposed control scheme not only guarantees that spacecraft attitude control errors converge toward a small invariant set containing the origin, but also ensures that there is no accumulation of triggering instants. The performance of the proposed control scheme is demonstrated through numerical simulation.     

A user-friendly yield criterion for metals exhibiting tension-compression asymmetry

The aim of this paper is to model the yielding asymmetry of pressure-insensitive metals, including but not limited to Ni₃Al alloys. The main focuses are put on the flexibility and manipulative convenience. The parameters of theory are kept to a minimum and can be determined by as few tests as possible. These requirements are fulfilled by constructing a yield function using the second and third-invariants of a linearly transformed stress tensor. The proposed yield criterion has a simple mathematical form and has only seven parameters when used in three-dimensional stresses. Compared with existing theories, the new yield criterion has much fewer parameters, which makes it very convenient for practical applications. The coefficients of the criterion are identified by an error minimization procedure. Applications to a Ni₃Al based intermetallic alloy as well as a Cu-Al-Be shape memory alloy and comparison to other criteria show that the proposed criterion has nearly the same predictive ability and flexibility with other criteria. The proposed yield criterion can estimate the coefficients by using less data, which is a big advantage compared with other similar theories, especially when there is a limited number of experimental data.     

航空发动机轴承腔热状态分析模型及温度场计算

分析了轴承腔的主要热源。建立了轴承及石墨密封摩擦热的计算模型、密封热泄漏量的计算模型、对流换热系数的计算模型及温度场的计算模型。用热网络法建立了轴承腔的热平衡方程组,并采用拟牛顿法求解了该方程组。获得了10种不同工况下的温度场计算结果,该结果与本文的测试结果基本吻合。      

1992年10月27日耀斑的多波段观测和分析

利用１９９２年１０月２７日耀斑极为完整的高质量观测资料,通过对可见光、软Ｘ射线和硬Ｘ射线图像和光谱的综合分析,诊断耀斑过程中的热与非热性质,结果表明,在这个事件中,热与非热过程并存且在时空演化上呈现不同的特征     

自适应光学技术补偿镜面温度及自重变形研究

论述了在星载高分辨率相机上采用自适应光学技术的必要性;介绍了应用自适应光学技术补偿镜面温度及自重变形的实验原理,进行了计算机模拟计算,并与实验结果进行比较。实验用一块平面反射镜作为缩比模型,应用６１单元自适应光学系统对其进行了闭环校正实验,分析了泽尼克多项式所对应的像差的校正效果。