数值仿真技术在热真空试验中的应用

由于热真空试验中温度测点有限,且关键部位布置困难,不能反映试验过程部件整体和关键部位的温度结果,导致试验有效性和产品安全性难以判断。通过数值仿真技术对试验过程进行模拟,得到所有部件详细温度场,验证试验有效性与产品安全性;发现影响产品温度分布的因素,研究提高产品可靠性措施。通过对某天线热真空试验过程模拟,得到天线详细温度场,并发现产品散热板安装＂不紧密＂缺陷,是影响天线温度均匀性的＂关键点＂。     

液体火箭发动机涡轮泵用机械密封温度场及热载变形研究

基于ANSYS数值计算软件,建立了液体火箭发动机涡轮泵用机械密封的二维稳态传热模型,依靠经验公式确定了模型的对流换热系数。计算了密封环的温度场和热载变形,分析了密封端面比压、回流流量以及不同材质对密封温度场的影响规律。结果表明:密封端面最高温度发生在靠近密封环内径处,且密封端面比压越大密封环温度梯度越大;密封环热载变形呈收敛间隙,最大变形发生在动环端面的外径处,其值约为2.2μm;密封环端面最高温度随回流流量增加而减小,当回流流量从0.1~0.6 kg/s变化时,密封环端面最高温度可降低18%(从100℃降至82℃);当回流流量增大到0.3 kg/s时,继续提高对密封环端面温升的控制不再显著;采用高导热系数的摩擦副材料能够显著降低端面温升和温度梯度,提高密封工作可靠性。     

微型化半球陀螺制备工艺发展现状及趋势分析

因低噪声、高性能、无磨损的优势,半球陀螺已成为航空、航天领域内的最佳导航陀螺。半球陀螺的微型化是微机电陀螺领域的研究热点,全球各研究单位设计了多种形态的谐振器结构,开发了各具特色的加工工艺,其选用的材质也各不相同,并研制出了形态各异的微半球陀螺结构。对半球陀螺微型化的历程和方式进行了综述,着重对微型化半球陀螺壳体谐振器的结构形态、工艺制备方法和选材进行了对比和分析,并对各微型化途径的特点进行了讨论和展望。     

基于Ansys Icepak 的负载器热设计与热分析

基于热设计的基础理论与负载器的工作原理,应用Ansys Icepak仿真软件对供配电负载器工作过程中内部散热情况进行仿真,找出负载器内部温度最高部位,指导实际测试,避免实际测试的盲目性。另外,通过优化负载器散热孔设计,降低负载器温升值。     

碳纤维热导率与其微观结构参数的关系

碳纤维具有多晶多相特性,为了研究微晶结构特性对热导率的影响,本文通过XRD对碳纤维的微观特征结构参数的表征,对导热性能与微观特征结构的关联性进行了研究。研究结果表明,碳纤维热导率随着石墨微晶的基面宽度（L_a）、堆砌厚度（L_c）和平均堆垛层数（N）的增大而增大,随着孔隙率（V_p）的增大而降低。基于Raman图谱的分峰拟合信息,对碳纤维的石墨化度进行分析。结果显示,碳纤维的石墨化度越大,热导率越高。     

干涉配合构件的应力腐蚀开裂特性

采用恒载荷拉伸实验技术,研究了镀锌３０ＧｒＭｎＳｉＡ锡螺栓干涉配合连接ＬＹ１２－ＣＺ铝合金构件在３．５％ＮａＣａｌ＋０．５％Ｈ２Ｏ２溶液中的应力腐蚀开裂特性。结果表明,随干涉量的增加,应力腐蚀敏感性有所下降,基材与紧固件的电偶效应对应力腐蚀繁感性有重大影响。     

Effects of yaw-roll coupling ratio on lateral-directional aerodynamic characteristics

Experimental investigation of large amplitude yaw-roll coupled oscillations was conducted in a low-speed wind tunnel using an aircraft configuration model. A special test rig was designed and constructed to provide different coupled motions from low to high angles of attack.A parameter ‘‘coupling ratio" was introduced to indicate the extent of yaw-roll coupling. At each pitch angle, seven coupling ratios were designed to study the yaw-roll coupling effects on the lateraldirectional aerodynamic characteristics systematically. At high angles of attack, the damping characteristics of yawing and rolling moments drastically varied with coupling ratios. In the coupled motions with the rotation taking place about the wind axis, the lateral-directional aerodynamic moments exhibited unsteady characteristics and were different from the ‘‘quasi-steady" results of the rotary balance tests. The calculated results of the traditional aerodynamic derivative method were also compared with the experimental data. At low and very high angles of attack, the aerodynamic derivative method was applicative. However, within a wide range of angles of attack, the calculated results of aerodynamic derivative method were inconsistent with the experimental data, due to the drastic changes of damping characteristics of lateral-directional aerodynamic moments with yaw-roll coupling ratios.     

PIP工艺制备SiC晶须增强SiCf/SiC复合材料的性能

以不同界面层厚度的SiC纤维为增强相,采用先驱体浸渍裂解工艺(PIP)制备SiC_f(PyC)/SiC复合材料,并在复合材料基体中引入SiC晶须,对其性能进行研究。结果表明:热解碳(PyC)界面层厚度约为230 nm时,SiC纤维拔出明显,SiC_f/SiC复合材料拉伸强度、弯曲强度和断裂韧度分别达到192.3 MPa、446.9 MPa和11.4 MPa?m^1/2;在SiC_f/SiC复合材料基体中引入SiC晶须后,晶须的拔出、桥连及裂纹偏转等增韧机制增加了裂纹在基体中传递时的能量消耗,使复合材料的断裂韧度和弯曲强度分别提高了22.9%和9.1%。     

Remote upgrading of a space-borne instrument

The main purposes of experiment “Obstanovka” (“Environment” in Russian) consisting of several instruments are to measure a set of electromagnetic and plasma phenomena characterizing the space weather conditions, and to evaluate how such a big and highly energy consuming body as the International Space Station disturbs the surrounding plasma, and how the station itself is charged due to the operation of so many instruments, solar batteries, life supporting devices, etc. Two identical Langmuir electrostatic probes are included in the experiment “Obstanovka”. In this paper the Langmuir probes for “Obstanovka” experiment are described, including the choice of geometry (spherical or cylindrical), a more reliable method for the sweep voltage generation, an adaptive algorithm for the probe’s operation. Special attention is paid to the possibility for remote upgrading of the instrument from the ground using the standard communication channels.     

Coupled Stress-Electricity Model for Electromagnetic Emission Induced by Concrete Fracture

Electromagnetic emission induced during concrete fracturing is of great significance to health monitoring of concrete structures.A coupled stress-electricity model is established by analyzing the interaction between stress and electricity during concrete fracturing.And based on this model,the electromagnetic radiation parameters are calculated.The theoretical calculation is well coincident with experimental results.This work provides theoretical support for concrete testing system.