环路热管地面实验平台的热设计

文章旨在建立环路热管的地面实验平台,模拟环路热管在太空轨道运行的热环境。首先建立了地面实验舱的物理模型,对其如何实现在地面模拟太空中该环路热管的热环境进行了热分析计算,其次确定了满足环路热管轨道运行最冷工况和最热工况下的实验舱的壁面温度,最后对实现该轨道环境所需要的壁面绝热材料、制冷剂、制冷设备进行了选择,初步完成了实验平台的热设计。计算结果表明,在同时考虑舱内对流和辐射换热的条件下,要实现空间热边界条件,实验舱内舱的壁温要保证在-62.1~-10.9℃之间变化。     

一种基于工程化气动加热算法的天线热防护设计

高超音速气动热仿真技术是提高天线热防护能力的重要支撑之一,为了进一步缩短研制周期和节约成本,本文提出了一种以冷壁热流和壁面恢复焓为输入条件,以MATLAB和CFD联合迭代快速求解高速气流中天线温度场的工程化算法。在利用气动热试验证明仿真结果与实验数据的高一致性后,以该仿真方法对一个高速气动加热时长为500 s的天线实施了防隔热优化设计,根据仿真评估出的导致核心器件温升的主、次要因素,针对性地提出改进措施,最终目标印制板由过往的320℃下降到了142℃,热控效果显著。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

基于混杂非对称复合材料的自适应对日定向器

提出并设计了一种基于混杂非对称复合材料层合板的新型自适应对日定向器。该对日定向器采用混杂非对称复合材料层合板作为驱动元件,利用在轨光照条件的变化引起复合材料层合板温度变化,进而使其产生热变形并驱动太阳翼发生偏转。提出的自适应对日定向器结合传统的单自由度对日定向机构,能够实现太阳能帆板的双自由度对日定向。介绍了自适应对日定向器的基本原理,并结合地球静止轨道的光照条件进行了具体设计。利用能量变分原理建立了混杂非对称复合材料的热变形模型,分析其热变形特点,并利用有限元方法对定向器在地球静止轨道上的温度场特性、热变形及对日定向转动角度进行分析。有限元分析结果表明,通过合理设计,自适应对日定向器的转角能够随太阳光入射角变化呈线性变化,定向精度可达±1°。     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真,以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化,建立终端的轨道热分析模型,准确模拟在轨机动,根据典型机动模式、外热流和涂层退化等因素设计了计算工况,得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异,最大可达23.0℃,采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度,甚至不能部分替代二维转动热分析或热试验;光学天线和反射镜的温度控制是制约终端工作的瓶颈,为终端设计合适的避光机动策略,可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

沥青基碳纤维热导率的间接法测量

文摘采用"四探针法"测定6种沥青基碳纤维单丝的轴向电阻率,通过3个经验公式计算得到其热导率,再将计算值与厂商公布值进行对比分析。结果表明:对于热导率600或300 W/(m·K)的碳纤维采用公式λ=1261/ρ计算得到的热导率值与厂商公布值最为吻合,而对于热导率在300~600 W/(m·K)的碳纤维采用公式λ=440 000/(100ρ+258)-295计算得到的热导率值与厂商公布值最为吻合。以此测试值为基础,建立了沥青基碳纤维单丝电阻率与其热导率的函数关系λ=152 740/(100ρ+22)-26,具有更强的普适性。     

潜入式喷管喉衬界面间隙优化设计

为了解决固体火箭发动机潜入式喷管喉衬在热载荷与内压联合作用下界面间隙优化问题,数值模拟方法求解了喷管热结构响应.采用流体仿真软件,计算了潜入式喷管流动过程的稳态流场,获取了高温燃气流动参数与固体壁面对流换热系数.并采用三维有限元结构计算平台,编写了非均布壁面压力载荷与非均布对流换热系数子程序,求解了喉衬前后搭接界面间隙...     

水冲压发动机的热力循环性能预示

针对采用二次进水机制的水冲压发动机,基于特殊的工作方式初步建立了相应的热力循环模型,进而在不同的发动机工况下分析了循环热效率性能。选定水反应金属燃料基础配方为Mg/AP/HTPB的混合物,在不同组分配方条件下,相应发动机热力循环效率随各影响参数的变化规律一致,均随燃烧室压强和水反应金属燃料中金属含量的增加而呈增加趋势,相反,水燃比的增加会引起热效率的降低。特别地,给定一合理水燃比3.0,保持燃烧室压强和航行器航深分别为2.5 MPa和10 m,50%和60%镁含量的水反应金属燃料对应发动机的循环热效率分别为37.78%和44.38%,初步验证了基于联合循环的水冲压发动机良好的循环性能。     

低功率激光-TIG电弧复合焊接不锈钢熔深研究

建立了一套低功率YAG脉冲激光-TIG电弧复合热源焊接系统,并用本系统对不锈钢1Cr18Ni9Ti进行焊接.研究了3种热源作用下不锈钢的焊缝熔深.通过引入焊缝有效热输入概念,对复合热源影响熔深的机理进行了分析.     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.