非定常动态旋涡显示

基于旋涡的密度梯度，研制一种用彩色纹影系统来实时显示非定常旋涡随攻角变化的动态过程，并与常规的激光片光技术相比有许多优点和潜力。     

A memetic algorithm for path planning of curvature-constrained UAVs performing surveillance of multiple ground targets

The problem of generating optimal paths for curvature-constrained unmanned aerial vehicles （UAVs） performing surveillance of multiple ground targets is addressed in this paper. UAVs are modeled as Dubins vehicles so that the constraints of UAVs＇ minimal turning radius can be taken into account. In view of the effective surveillance range of the sensors equipped on UAVs, the problem is formulated as a Dubins traveling salesman problem with neighborhood （DTSPN）. Considering its prohibitively high computational complexity, the Dubins paths in the sense of terminal heading relaxation are introduced to simplify the calculation of the Dubins distance, and a boundary-based encoding scheme is proposed to determine the visiting point of every target neighborhood. Then, an evolutionary algorithm is used to derive the optimal Dubins tour. To further enhance the quality of the solutions, a local search strategy based on approximate gradient is employed to improve the visiting points of target neighborhoods. Finally, by a minor modification to the individual encoding, the algorithm is easily extended to deal with other two more sophisticated DTSPN variants （multi-UAV scenario and multiple groups of targets scenario）. The performance of the algorithm is demonstrated through comparative experiments with other two state-of-the-art DTSPN algorithms identified in literature. Numerical simulations exhibit that the algorithm proposed in this paper can find high-quality solutions to the DTSPN with lower computational cost and produce significantly improved performance over the other algorithms.     

机载SAR反投影图像自聚焦处理方法

反投影算法(BPA)是一种经典的时间域合成孔径雷达(SAR)成像处理方法。BPA对回波数据插值累加得到图像,运动误差导致的目标散焦沿不同的倾斜角度存在,无法直接应用现有的自聚焦算法。为此,提出了一种新颖的BPA图像运动补偿方案。基于反投影数据运动相位误差和距离徙动分析,研究了修正投影栅格成像,从而去除重建图像中目标散焦方向的空变特性。在中低分辨率配置下,重建SAR图像能够直接应用相位梯度自聚焦(PGA)等进行运动补偿。点目标仿真实验和实测数据结果验证了该算法的有效性。     

旋转盘腔轴向通流的压降和温升数值研究

为获得旋转雷诺数对盘腔轴向通流温升和压降的影响,对轴向通流雷诺数(Re_x)恒定为1.0′10^₅、旋转雷诺数(Re_w)在0~5.31′10^₆之间、绝热边界下的流动进行了数值模拟,从流场特征、盘面绝热温升以及轴向通流压降和温升等三个方面进行了分析。研究表明,旋转雷诺数对于盘腔内部和轴向通流的流动均具有显著影响;尽管是绝热盘面,但是由于高速旋转的黏性耗散作用引发盘腔内气流的温升,由温度差引起的浮升力对于盘腔内流动和盘面温度分布的影响也是不可忽略的;随旋转雷诺数增大,轴向通流出口温度相对进口温度的温升急剧增大,在旋转雷诺数小于2.5′10^₆时,轴向通流相对温升系数在0.01以内,当旋转雷诺数大于4.5′10^₆时,轴向通流相对温升系数达到0.04以上。     

Fatigue life prediction model of 2.5D woven composites at various temperatures

As one of the new structural layout in the family of woven composites, 2.5D Woven Composites(2.5D-WC) have recently attracted an increasing interest owing to its excellent properties, i.e. high specific strength and fatigue resistance, in the aerospace and automobile industry. Indepth understanding of the fatigue behavior of this material at un-ambient temperatures is critical for the engineering applications, especially in aero-engine field. Here, fatigue behavior of 2.5D-WC at different temperatures was numerically investigated based on the unit cell approach. Firstly, the unit cell model of 2.5D-WC was established using ANSYS software. Subsequently, the temperature-dependent fatigue life prediction model was built up. Finally, the fatigue lives alongside the damage evolution processes of 2.5D-WC at ambient temperature(20 ℃) and unambient temperature(180 ℃) were analyzed. The results show that numerical results are in good agreement with the relevant experimental results at 20 and 180 ℃. Fatigue behavior of 2.5D-WC is also sensitive to temperature, which is partially attributed to the mechanical properties of resin and the change of inclination angle of warp yarns. We hope that the proposed fatigue life prediction model and the findings could further promote the engineering application of 2.5D-WC, especially in aero-engine field.     

高速撞击梯度电势靶板产生等离子体诱发的放电

针对在轨运行航天器在空间等离子体环境和空间带电粒子活动下诱发航天器表面梯度电势存在的客观现实,航天器在空间碎片的撞击下会诱发表面带电或深层电介质带电的航天器放电。为了在实验室模拟航天器表面存在电势差的真实情况,采用对航天器外表面分割的方法,在分割的表面间预留不同间距且在2靶板间加装电阻的方法创造具有梯度电势的高电势2A12铝板作为靶板。利用自行构建的梯度电势靶板的充放电测试系统、超高速相机采集系统和二级轻气炮加载系统,开展高速撞击梯度电势2A12铝靶的实验室实验。实验中,弹丸以入射角度为60°（弹道与靶板平面的夹角）、撞击速度约为3 km/s的条件撞击间距分别为2、3、4和5 mm的2A12铝高电势靶板,利用电流探针和电压探针采集放电电流和放电电压。实验结果表明:放电产生的等离子体形成了高电势与低电势靶板间的放电通道,且在梯度电势靶板间距分别为2、3 mm时诱发了一次放电,放电电流随高低电势靶板间间距的增加而减小;在梯度电势靶板间距分别为4、5 mm时诱发了二次放电,放电电流随高低电势靶板间间距的增加变化不明显。      

北京上空高分辨率气球探空观测的温度垂直波数谱

使用分辨率为10 m的温度剖面检查2.90～8.01 km和14.65～19.76 km高度范围内归一化温度扰动谱的谱特性,并且将它们与模式谱比较.结果表明,在波数9.8×10-4～2.5×10-2m-1范围内,对流层的垂直波数谱有约-1.9的平均谱斜率;低平流层的垂直波数谱有约-2.2的平均谱斜率.这两个平均谱斜率大大偏离了目前饱和谱模式和普适大气谱模式表示的-3.0和-2.4谱斜率,并且认为是目前气球测量中曾经观测到的最平谱斜率.在波数9.8×10-4～2.5×10-2m-1范围内,对流层和低平流层的平均谱振幅比饱和谱模式的谱振幅分别大24倍和5倍,这也与饱和谱模式以及目前文献中的观测结果有很大不同.这些较大平均谱振幅与最平的平均谱斜率一道共同表明,观测的温度谱并不遵循目前的饱和谱模式和普适大气谱模式.      

温度冲击试验对固体发动机喷管堵盖结构影响的仿真分析

温度冲击试验可模拟极端温度环境对固体发动机结构的影响。本文利用三维有限元方法,通过热-机耦合,分析了一种固体发动机喷管堵盖在温度冲击中的温度、应力和应变的变化情况。结果表明:温度冲击中,喷管堵盖内存在温差,最大可达46℃;存在内应力,在铝合金支撑件/EP密封件环形界面处最大,低温-50℃时达18.1 MPa,是堵盖最先破坏的位置;EP密封件是堵盖的最薄弱环节,粘接结构最大内应力11.6MPa,分离结构9.1 MPa;得出了温度冲击下,影响喷管堵盖结构完整性的因素,表明选用低模量和合适线胀系数的密封材料,采用常温成型方法,脱开密封件/支撑件间环形交界面,可有效降低密封件/支撑件的内应力;含GFM/EP/铝合金喷管的真实发动机温度冲击试验结果与预估结果吻合。     

A novel temperature-compensation method based on correlation analysis for multi-FOG INS

Aimed at improving the bias stability of Fiber-Optic Gyroscope (FOG)-based inertial navigation systems in environments of various ambient temperatures, a novel temperature-compensation method based on a correlation analysis of the same batch of FOGs is proposed. The empirical mode decomposition method was employed to filter the high-frequency noises of the FOGs. Then, the correlation information of the multiple FOGs was used to analyze the feasibility of the method. Eventually, the same residual error of the FOGs was compensated via the simple piecewise linear models. The experimental results indicate that excellent compensation effects for both high- and low-accuracy FOGs are achieved using the proposed method. Specifically, the accuracies of high-accuracy FOGs are improved by approximately 33.9%, 20%, and 31.2%, while those of low-accuracy FOGs are improved by approximately 39.1%, 20.8%, and 26.1%. The method exhibits the merits of simplicity, validity, and stability, and thus is expected to be widely used in engineering applications.     

基于EFPI-FBG结构的光纤复合传感器研究

研究了一种基于非本征型Fabry-Perot干涉仪(EFPI)和光纤Bragg光栅(FBG)串联结构构成的EFPI-FBG光纤复合传感器,用于实现对压力和温度信号的同步测量。传感器选用熔融石英作为压力敏感材料,利用飞秒激光焊接技术实现传感器探头结构的封装。对传感器的工作原理进行了分析,制作并封装传感器工程样机,搭建测试系统,对传感器的性能进行了灵敏度及交叉敏感性分析。结果表明,该传感器在0.8 MPa范围内的灵敏度约为-0.729μm/MPa,在50℃~200℃范围的温度灵敏度为0.009 nm/℃,传感器压力测量最大允许误差为±4.12%FS。该EFPI-FBG复合传感器有望应用于压力—温度双参数测量需求的技术领域。