固体微推力器设计与数值分析

设计了两种基于微光机电技术的固体微推力器结构,其中一种结构具有不连续的非正常拉瓦尔喷管。采用数值计算方法对不同的设计进行了内弹道、燃气流动过程和热损失的数值分析。结果表明:不连续的非正常拉瓦尔喷管同样能够将推进剂燃气加速到超声速,其比冲性能与正常拉瓦尔喷管相当;微光机电技术常用的硅材料会造成推力器比冲性能较大量级的下降,而绝热性能良好的玻璃或陶瓷材料可以有效提高微推力器的比冲性能。     

涡流阀几何参数对固体发动机推力调节特性的影响

为了获得涡流阀参数对发动机推力调节性能的影响规律,针对涡流阀的加注方式以及几何结构,利用建立的基于涡流阀方案的固体火箭发动机推力可调实验系统开展了实验研究。通过实验结果的分析,得到了加注环孔径、涡流室高度和直径以及中心进气面积的不同对涡流阀调节性能的影响规律。结果表明:适当降低涡流室的高度、较大的中心进气面积、较大的涡流室直径有利于提高涡流阀的调节性能。因此,可以通过对涡流阀结构的优化设计来提高发动机的推力调节性能。     

基于图形变形法的固体火箭发动机优化设计

基于图形变形法探索固体火箭发动机优化设计空间，通过可视化展示设计空间形态，能够提高固体火箭发动机优化设计效率和质量。采用试验设计方法对设计变量和约束条件重要性进行排序，简化优化模型；采用图形变形法对简化优化模型在不同试验设计点进行可视化分析；可视化选取可行设计空间中目标函数较小的点作为初始点。应用三种常规优化算法对4个不同初始点进行优化计算，计算结果表明，图形变形法优选的初始点使优化效率有不同程度的提高，优化结果具有更好的全局最优解特性；与遗传算法比较，效率提高400倍以上。     

发动机装药应变测试方法实验研究

介绍了用弓形传感器测试固体发动机模拟器的装药在硫化降温过程中的应变情况，并将结果与理论计算进行了对比，分析表明：实验结果与计算结果和定性分析结果附合良好，虽然在实验过程中温度控制不够严格，两种结果有一定的误差，但当温度达到基本平衡时，两种结果吻合很好。     

空载固体发动机计算与试验模态相关性分析

为了预测空载状态固体火箭发动机动态特性,对其进行了模态试验,并应用MSC.Marc进行了模态计算,然后对比两者的结果,进行了相关性分析和评估。计算得到了发动机250Hz以内的一阶弯曲模态和五阶呼吸模态。试验测得了发动机的三阶呼吸模态和一阶弯曲模态。比较试验测试模态和与之对应的计算模态:固有频率相对误差均在5%以内;振型相关图上的点大都分布在斜率为1(或 1)的直线周围;MAC(模态置信判据)值在0 9左右。说明计算与试验模态有较好的相关性,有限元计算模型比较准确的反映了实际情况。     

高空高速无人飞行器热控制系统设计

针对飞行时间短、速度和高度变化快、表面温度波动大的无人飞行器UAV(Unmanned Aerial Vehicles)热控制系统设计难题,提出了一种可解决实际工程问题的热分析计算方法.即把热天工况、冷天工况和标准天工况作为设计/试验工况;采用参考温度法、高超音速工程预测法或计算流体动力学CFD(Computational Fluid Dynamics)数值模拟法,确定了飞行器表面温度分布,并把其作为后续热分析数学模型的外边界条件;分析结构热容量对瞬态热载荷的影响,建立与之相应的边值问题方程,并采用有限差分法求解;根据高空高速飞行特点及瞬态热载荷值,确定仪器设备舱调温系统方案.     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

WSO-UV project

During last three decades, astronomers have enjoyed continuous access to the 100–300 nm ultraviolet (UV) spectral range where the resonance transitions of the most abundant atoms and ions (at temperatures between 3000 and 300 000 K) reside. This UV range is not accessible from ground-based facilities. The successful International Ultraviolet Explorer (IUE) observatory, the Russian ASTRON mission and successor instruments such as the Galaxy Evolution Explorer (GALEX) mission or the COS and STIS spectrographs on-board the Hubble Space Telescope (HST) prove the major impact of observations in the UV wavelength range in modern astronomy. Future access to space-based observatories is expected to be very limited. For the next decade, the post-HST era, the World Space Observatory – Ultraviolet (WSO–UV) will be the only 2-m class UV telescope with capabilities similar to the HST. WSO–UV will be equipped with instruments for imaging and spectroscopy and it will be a facility dedicated, full-time, to UV astronomy. In this article, we briefly outline the current status of the WSO–UV mission and the science management plan.     

Particle swarm optimization applied to hypersonic reentry trajectories

This paper presents the novel use of the particle swarm optimization(PSO)to generate the end-to-end trajectory for hypersonic reentry vehicles in a quite simple formulation.The velocitydependent bank angle profile is developed to reduce the search space of unknown parameters based on the constrained PSO algorithm.The path constraints are enforced by setting the fitness function to be infinite on condition that the particles violate the maximum allowable values.The PSO algorithm also provides a much easier means to satisfy the terminal conditions by adding penalty terms to the fitness function.Furthermore,the approximate reentry landing footprint is fast constructed by incorporating an interpolation model into the standardized bank angle profiles.Numerical simulations demonstrate that the PSO method is a feasible and flexible tool to generate the end-to-end trajectory and landing footprint for hypersonic reentry vehicles.     

潜入式喷管喉衬界面间隙优化设计

为了解决固体火箭发动机潜入式喷管喉衬在热载荷与内压联合作用下界面间隙优化问题,数值模拟方法求解了喷管热结构响应.采用流体仿真软件,计算了潜入式喷管流动过程的稳态流场,获取了高温燃气流动参数与固体壁面对流换热系数.并采用三维有限元结构计算平台,编写了非均布壁面压力载荷与非均布对流换热系数子程序,求解了喉衬前后搭接界面间隙...