强激波-附面层干扰下的气流动态畸变研究

本文在一定附面层条件下,着重研究典型的强激波与紊流附面层干扰区下游扩压器出口的气流动态畸变,文中讨论了激波强度、扩压器壁面形状(直壁和曲壁)对动态畸变的影响.讨论了紊流度分布中四个峰值与相同截面上的总压沿高度分布的相互关系.最后对紊流度沿高度分布中的若干典型站的总压信号作功率谱密度和概率密度函数分析     

二维非常规压缩型面超/高超声速进气道的设计概念

为了提高满足一定尺寸要求的进气道的性能,提出了一种非常规压缩型面进气道,并用数值模拟手段对该进气道和常规的二维斜楔式进气道的性能进行了比较。数值模拟结果表明,设计工况下该进气道能够获得跟常规二维斜楔式进气道大致相当的气动性能。非设计工况下,该进气道性能优于常规进气道。一体化设计时,该进气道对保持前机体来流附面层的稳定性十分有利。     

The multifuid solar wind termination shock and its influence on the threedimensional plasma structure upstream and downstream

The solar wind termination shock is described as a multi-fluid phenomenon taking into account the magnetohydrodynamic self-interaction of a multispecies plasma consisting of solar wind ions, pick-up ions and shock-generated anomalous cosmic ray particles. The spatial diffusion of these high energy particles relative to the resulting, pressure-modified solar wind flow structure is described by a coupled system of differential equations describing mass-, momentum-, and energy-flow continuities for all plasma components. The energy loss due to escape of energetic particles (MeV) from the precursor into the inner heliosphere is taken into account. We determine the integrated properties of the anomalous cosmic ray gas and the low-energy solar wind. Also the variation of the compression ratio of the shock structure is quantitatively determined and is related to the pick-up ion energization efficiency and to the mean energy of the downstream anomalous cosmic ray particles. The variation of the resulting shock structure and of the solar wind sheath plasma extent beyond the shock is discussed with respect to its consequences for the LISM neutral gas filtration and the threedimensional shape of the heliosphere.     

考虑高载和阻尼介质时刚塑性圆板的塑性动力分析

本文研究了阻尼介质对刚塑性圆板在高载(冲击荷载)作用下塑性动力响应的影响,得到了解析解并对此解进行了讨论。当阻尼介质参数趋于零时,本文结果与无阻尼解一致。文中还画出了荷载与阻尼介质对圆板运动时间和板中心点残余挠度的影响曲线。     

行星际空间MHD模拟激波跃变关系分析

分析了模拟得到的可以传播到1AU以远的日地空间磁流体力学激波与Rankine-Hugnoniot跃变关系的符合程度．通过对模拟激波的结构及其在传播过程中的演化进行的分析，提出了模拟激波的定位方法；基于所提出的定位方法，利用向长青提出的确定MHD激波局地参数的方法计算了模拟得到的激波与Rankine-Hugnoniot跃变关系的偏差．结果表明在激波传播到100Rs以后，激波对中前向快激波与Rankine-Hugnoniot关系的符合达到很高的程度，相对误差在10^-2数量级以内；并且在激波传播到150 Rs以后，相对误差在10^-3数量级以内．这个结果说明文中所使用的有限差分数值格式能较好地模拟激波．     

Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

Alfvén gravity waves in viscous solar plasma: Effect of the background flow

We study the Propagation and damping properties of Alfvén gravity waves in the presence of the vertical magnetic field in the viscous solar plasma under influence of the background flow by deriving a fourth order dispersion relation in terms of the Doppler shifted frequency. We derive the dispersion relation under WKB and Boussinesq approximation. We study the damping of Alfvén gravity waves for the wave frequencies less than and greater than the Brunt-Väisälä frequency. We find that the Brunt-Väisälä frequency divides the frequency ranges where the weakly or strongly damped oscillations occur. The background flow exhibits a strong effect on weakly damped oscillations and a weak effect on the strongly damped oscillations. We also notice that the damping of both the strong and weakly damped oscillations depend on the Brunt-Väisälä frequency and wave number. The effect of the background flow is also being governed by the Brunt-Väisälä frequency and wave number. We also study the properties of gravity wave mode after filtering the Alfvén wave mode by minimizing the magnetic field and noticed that the background flow shows a very strong effect on the gravity wave mode.     

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.