Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

涡轮流量计前导流件有限元计算分析

对涡轮流量计关键部件之一前导流件运用NX THERMAL/FLOW进行有限元计算分析,得出流量分离导致的大涡旋尾迹区易出现在前导流件尾部区域、前导流件叶片形状对此处流体速度变化具有较大影响的结论,为涡轮流量计和前导流件的设计提供了理论依据。     

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

突加不平衡下GTF发动机转子系统瞬态响应分析

针对GTF发动机低压转子系统突加不平衡瞬态响应问题,基于有限元法建立了考虑啮合单元、行星架单元、膜盘联轴器单元的多体接触、多转子耦合动力学模型,介绍了考虑非线性因素下突加不平衡瞬态响应计算方法,求解了低压转子系统的突加不平衡瞬态响应,并分析了关键部件刚度对突加不平衡的影响规律。结果表明：当风扇转子发生突加不平衡时,各部件均表现为振动幅值突增,后迅速趋于稳定,低压涡轮转子发生明显拍振,突加不平衡载荷主要由行星架结构和第1.5支点刚性支承承担;行星架刚度主要影响风扇转子突加不平衡响应、第1.5支点和行星架处的外传力;膜盘联轴器刚度主要影响增压级突加不平衡响应、转子在突加不平衡之后稳定运转情况。     

一种小天体旋转参数估计方法

小天体旋转参数是科学数据,也是小天体测绘,着陆导航的基础数据.研究一种在小天体探测接近段过程中使用的基于图像上特征点跟踪和扩展卡尔曼滤波器的小天体旋转参数估计方法.该方法首先建立小天体旋转关系模型,表示小天体在相机坐标系中的姿态变化;然后定义小天体旋转的状态方程,推到了扩展卡尔曼滤波器的计算过程.通过对观测图像序列上的特征点跟踪,利用扩展卡尔曼滤波器方法得到小天体旋转轴指向和自转角速度估计.实验中,在仿真相机与小天体相机100 km距离上,分析了相机坐标系小天体坐标系之间的四元数初值,图像上特征点跟踪精度,相机的观测指向等因素对小天体旋转参数估计精度的影响.实验结果表明,提出的基于图像特征点跟踪和扩展卡尔曼滤波器的小天体旋转参数估计方法能够得到具有较高精度的估计结果.     

非对称来流下隔离段动态压力特性

为了探讨非对称来流下矩形隔离段内动态压力特性,用直联实验方式以及动态压力测量技术进行了试验,并用统计分析方法分析了数据。实验结果表明,入口来流的非对称性对上下壁面压力脉动大小以及传播平均速度有较大影响,而对频率无多大影响。激波串区域内壁面压力脉动向下游传播比向上游传播衰减得快。在隔离段出口超声速条件下,观测到的压力脉动频率主要在70 Hz以下,而在出口亚声速条件时,压力脉动的频率不仅有70Hz以下的部分,而且还有100~200 Hz之间的部分。     

超声速进气道喉部附面层抽吸

为研究超声速进气道喉部之后流场激波附面层干扰,采用FLUENT软件模拟了单楔角进气道在设计工况下流动情况。通过分析,提出进气道喉部抽吸。计算了三种抽吸缝大小下进气道喉部之后流场,计算结果表明,喉部抽吸能使激波稳定于喉部,通过抽吸能改善喉部之后流场状况,提高进气道性能,少量抽气不改变流场结构,加大抽气量,使喉部之后激波串转变成正激波,正激波之后流场不分离,进气道出口性能参数提高显著。     

几种超声速非常规压缩系统的研究

根据斜激波和膨胀波理论,数值计算得到给定非常规压缩型面所形成的弯曲激波型面和壁面静压分布,同Fluent计算结果进行比较。应用Fluent软件,计算了等压力梯度设计非常规曲面压缩二元进气道、常规等熵压缩二元进气道和三楔压缩二元进气道设计点性能。研究结果表明:数值计算得到的弯曲激波型面与Fluent计算结果吻合较好。等压力梯度设计的非常规压缩型面壁面静压均匀上升,有利于防止壁面附面层分离;其压缩面长度比等熵压缩面缩短21.6%,减轻了进气道的重量。     

MTPS蜂窝夹芯结构传热性能及热应力分析

对于金属防热结构的蜂窝夹芯结构的稳态情况,基于材料的全灰体假设,同时考虑热传导和热辐射两种传热形式对温度场的耦合作用,利用热流量守恒建立了蜂窝芯层温度场的非线性积分方程。离散化后利用数值方法得到方程组的数值解。对于美国兰利研究中心的实验结果,与本文方法的对比计算结果基本吻合。进一步,利用计算结果讨论了给定面板温度边界情况下,下面板、柱体层的灰度、蜂窝结构长径比对夹芯温度场的影响。并根据温度场和近似的应力分析模型,用半解析结果讨论了稳态情况下蜂窝芯层上的热应力。     

基于体积力模型的1维涡轮特性评估方法

涡轮低维气动特性评估方法的预测精度对涡轮气动设计有重要意义.基于适用于轴流涡轮特性评估的1维体积力方法,分析和局部调整了Adam和Leonard的1维体积力模型中的叶片力源项和离心力源项,并在特性计算中引入涡轮损失模型.通过1个低压涡轮和1个含冷气高压涡轮对该方法进行验证,计算结果表明:该方法对2个算例在涡轮设计工况点的流量效率预测偏差均在1％以内,且能够反映涡轮气动特性随膨胀比的变化趋势,具有良好的精度,可用于快速可靠地评估涡轮低维气动特性.