A seventh-order model for dynamic response of an electro-hydraulic servo valve

In this paper, taking two degrees of freedom on the armature–flapper assembly into account, a seventh-order model is deduced and proposed for the dynamic response of a two-stage electro-hydraulic servo valve from nonlinear equations. These deductions are based on fundamental laws of electromagnetism, fluid, and general mechanics. The coefficients of the proposed seventhorder model are derived in terms of servo valve physical parameters and fluid properties explicitly.For validating the results of the proposed model, an AMESim simulation model based on physical laws and the existing low-order models validated by other researchers through experiments are used to compare with the seventh-order model. The results show that the seventh-order model can reflect the physical behavior of the servo valve more explicitly than the existing low-order models and it could provide guidance more easily for a linear control design approach and sensitivity analysis than the AMESim simulation model.     

大功率高性能航天伺服系统发展综述

回顾了电动、电静液伺服系统国内外发展历程与研究现状,针对未来航天飞行器对伺服系统在结构强度、空间体积、环境适应性、性能指标等方面提出的新要求,在综合评价电动、电静液伺服系统性能的基础上,指出了机载功率电传一体化电作动系统关键技术与设计难点,并提出相应的解决思路,对未来一体化电作动系统发展进行了展望。     

某精密三轴转台O型框架的一种改进设计

该文利用有限元原理建立了精密三轴转台O型框架有限元模型。通过对转台静态和动态载荷的分析,得出了三轴转台O型框架的有限元模型的边界条件,对转台O形框架的不同长宽比的情况下作出分析比较,在此基础上提出了一种新形式的变截面O型框架结构,这种结构的质量减轻,转动惯量减小,通过对其刚度及应力可靠性评估,证明这种新结构形式的框架也是可靠的。     

带伺服滑环和空气静压轴承的转台主轴干扰力矩的实验研究

带滑环伺服系统且采用空气静压气浮轴承的高精度陀螺漂移伺服转台，其控制精度受到气浮轴承粘滞力矩、涡流力矩、轴系质量配置不当造成的静不平衡力矩和滑环伺服系统对主轴干扰力矩的影响。本文通过理论分析和实验研究认为，当主轴轴系垂直于地面放置时，其主要干扰力矩来自滑环伺服系统。论文在对实验数据进行各项检验和处理的基础上给出了主轴常值和随机干扰力矩的数学表达式，为进一步提高同类伺服转台的伺服精度提供了一条有效的途径。     

Matching design of hydraulic load simulator with aerocraft actuator

 This paper intends to provide theoretical basis for matching design of hydraulic load simulator (HLS) with aerocraft actuator in hardware-in-loop test, which is expected to help actuator designers overcome the obstacles in putting forward appropriate requirements of HLS. Traditional research overemphasizes the optimization of parameters and methods for HLS controllers. It lacks deliberation because experimental results and project experiences indicate different ultimate performance of a specific HLS. When the actuator paired with this HLS is replaced, the dynamic response and tracing precision of this HLS also change, and sometimes the whole system goes so far as to lose control. Based on the influence analysis of the preceding phenomena, a theory about matching design of aerocraft actuator with HLS is presented, together with two paired new concepts of "Standard Actuator" and "Standard HLS". Further research leads to seven important conclusions of matching design, which suggest that appropriate stiffness and output torque of HLS should be carefully designed and chosen for an actuator. Simulation results strongly support that the proposed principle of matching design can be anticipated to be one of the design criteria for HLS, and successfully used to explain experimental phenomena and project experiences.     

线加速度台中稳速台转动对随动台定位稳定性的影响

针对线加速度台用于加速度计测试时,随动台定位受稳速台旋转干扰的现象进行了分析,提出被测设备质量要在负载允许范围内,使设备质心尽可能靠近随动台回转中心,并对其配平,以使稳速台转动带来的干扰力矩大大降低,保证测试中随动台的定位准确度及稳定性。     

精密伺服转台控制系统的设计与实现

本文设计并研制了高精度伺服转台的控制系统。从控制系统的伺服原理方案出发,详细的介绍了三轴精密伺服转台控制系统的硬件和软件的工程实现。该系统采用基于高速DSP为核心的控制器的双闭环伺服控制方案。实验测试结果均达到了设计指标和精度要求,表明系统设计方案的实用性和有效性。     

转台中心轴线标定误差分析与修正

提出一种标定球和几何变换相结合的方法修正三维激光数字化系统中转台中心轴线的标定误差.该方法首先用8个不同旋转位置的标定球球心计算转台中心轴线,然后利用几何变换将不同位置的球心绕转台中心轴线旋转到零度位置,并计算与初始位置球心的偏差,依据不同位置球心旋转复位的偏差采用几何逆变换推导出转轴偏心的修正公式.在自行设计的三维激光线扫描测量平台上数据旋转拼合精度提高到0.07?mm,实现了多视旋转测量的数据点云在线自动拼合.与以前的方法相比,设计的转轴标定误差修正方法简单、高效,在其它安装转台的测量系统中同样适用.     

三轴转台误差源对陀螺加速度表测试的影响

分析了三轴转台设备误差源;讨论了转台误差对陀螺加速度表测试精度的影响。根据陀螺加速度表的输入输出模型,建立了转台误差对陀螺加速度表系数辨识影响的数学表达式。     

基于DSP的导弹舵机控制系统的研究

应用TMS32 0F2 4 0DSP设计了全数字无刷直流电机的新型导弹舵机伺服驱动系统 ,详细介绍了系统的组成原理、硬件设计及控制策略。试验结果表明 ,此系统具有良好的动态和静态特性。