基于旋转高频信号注入法的内置式永磁同步电机低速段转子位置检测及其误差补偿

旋转高频信号注入法注入信号较为稳定,且位置估计过程不依赖电机参数,因而十分适用于内置式永磁同步电机(IPMSM)的零、低速转子位置检测。针对传统高频信号注入法无法辨别磁极的问题,用电压方波注入法检测磁极,结合有限元软件仿真,来合理选取方波电压幅值和时长,有效缩短了磁极判断耗时。分析了滤波器和信号离散化对位置估计精度的影响,提出在低速段可用线段拟合带通滤波器中心频率处的相频特性曲线,推导所需补偿角度与电机转速的关系。在理论分析的基础上,采用基于DSP28335的样机平台进行试验,结果表明磁极判断过程稳定,耗时较短,补偿后的位置估计值相比补偿前有明显改善,调速过程中系统动态性能良好。     

Design and optimization of a novel electrically controlled high pressure fuel injection system for heavy fuel aircraft piston engine

The heavy fuel compression ignition engines are widely equipped as aircraft piston engines. The fuel injection system is one of the key technologies that determines the performance of engine. One of the main challenges is to precisely control the injected fuel quantity and flow rate in the presence of pressure fluctuation. This challenge is even more serious for heavy fuel. An original design for electrically controlled high pressure fuel injection system called Multi-Pumppressure-reservoirs fuel injection System(MPS) was demonstrated to reduce the pressure fluctuation and help keep injection stable. MPS was compared with an ordinary high pressure Common Rail fuel injection System(CRS). This work established one-dimensional AMESim and mathematical models for both CRS and MPS to study the effect of different structures and geometric parameters on the pressure fluctuations. The calculations show that the average fuel pressure fluctuation of MPS can be reduced by 57% for the crankshaft speed of 1900 r/min, and the pressure fluctuation before injection reduced by 100%. It is concluded that the pressure performance of MPS is less sensitive to pressure reservoir volume than that of CRS, and there is an opportunity for further volume reduction.     

基于LPV状态空间模型的小型航空煤油二冲程发动机喷油控制策略

为了简化基于平均值模型的喷油控制模型的计算,根据线性变参数(LPV)状态空间模型原理,在平均值模型的基础上建立了LPV状态空间喷油控制模型,利用Matlab/Simulink工具对稳态工况和瞬态工况的喷油脉宽控制模型进行仿真,最后在发动机试验台架上进行试验验证.仿真和试验结果表明:①基于LPV状态空间模型的喷油控制模型能够满足瞬态工况和稳态工况控制的要求,计算的喷油脉宽精度略低于平均值模型,由于LPV状态空间模型计算简单,能够直接应用于控制算法的设计,因此在工程中容易实现.②与插值算法相比,基于LPV状态空间模型的控制策略使发动机的动力输出有所下降,主要是由于模型简化造成进气空气流量减小引起的.      

考虑喷油润滑的附件机匣温度场分析

附件机匣作为航空发动机重要部件之一,其产热和散热的问题比较复杂.针对以往附件机匣相关研究只关注固体域的产热、散热分析,而对滑油散热作用不能充分考虑这一问题的现状,提出了基于流体仿真思想的稳态温度场分析方法.首先,通过分析附件机匣产热、散热问题的基本规律和特点,进一步采用k-ε湍流模型来模拟机匣内的情况,多相流模型模拟滑油,并且使用多参考坐标系模拟滑油在运动过程中的换热.最后,以某附件机匣作为具体应用案例,验证了方法的正确性和可行性,从而形成了一套行之有效的使用FLUENT软件对附件机匣进行稳态温度场仿真分析的模型和方法.研究的成果对于后续附件机匣的可靠性与寿命分析有重要支撑作用.      

姿态角幅值约束下的太阳帆Lissajous轨道保持控制

太阳帆航天器以两姿态角作为轨道控制输入时, 其轨道动力学方程具有非仿射非线性特性. 通过人工平动点处线性化获得的线性系统可完成太阳帆航天器轨道保持控制器的分析与设计. 由于线性近似模型为有误差模型, 存在近似有效范围约束, 表现为轨道高度约束和姿态角幅值约束. 本文研究了姿态角幅值约束对线性近似模型有效性的影响, 通过计算给出满足近似误差要求的姿态角幅值约束. 当控制输入存在幅值约束时, 控制器轨道修正能力受到束缚. 通过研究姿态角幅值约束下的最大允许入轨误差, 设计了最大允许入轨误差下线性二次型调节器(LQR)用于轨道保持控制, 并将控制器应用于太阳帆日地三体系统非线性模型中, 实现了日地人工L₁点Lissajous轨道最大允许入轨误差的控制收敛和良好精度下的轨道保持控制.      

New trade tree for manned mars missions

Recent studies on human missions to Mars suggest revisiting the parameters that have the most important impact on the complexity, the initial mass in low Earth orbit, the risks and the development costs for the first journey to the red planet. In the last NASA reference mission, a trade tree is proposed.     

Numerical investigation of the impact of asymmetric fuel injection on shock train characteristics

Numerical simulations are carried out to investigate the impact of asymmetric fuel injection on shock train characteristics using the commercial-code FLUENT. The asymmetry of fuel injection is examined by changing the fuel flow rates of the upper and lower wall fuel injectors. The numerical approach solves the two-dimensional Reynolds-averaged Navier–Stokes (RANS) equations, supplemented with a k-ω model of turbulence. As a result, different ways of fuel injections will always lead to shock train transitions, with the variations of shock train structure, strength and leading edge position. For symmetric fuel injection, the flowfield of the isolator is quite asymmetric with the boundary layer of the upper wall side developing much stronger than that of the lower wall, which is due to the heterogeneity of the incoming flow. Regarding to asymmetric fuel injection with more of lower wall side, though the pressures in the combustor are nearly the same, the first shock of the shock train converts between ‘Distinct symmetric X type shock’ and ‘Obscure and weaker asymmetric shock’ and the shock train leading edge moves upstream with the increase of the asymmetry level. With regard to asymmetric fuel injection with more of upper wall side, ‘incomplete asymmetric X type shock’ occurs and the shock train structures keep nearly the same with low level of fuel injection asymmetry. Unexpected results like unstart will happen when increasing the level of fuel injection asymmetry. And the isolator will come back to normal state by decreasing the differential of upper and lower wall sides fuel injections.     

基于CATIA/CAA的四轴自动钻铆定位系统干涉检测编程方法研究及应用

干涉检测是自动钻铆加工前的重要准备工作,全文分别通过几种不同的干涉检测方法实现了运动仿真中的干涉检测,通过对各自方法取得的实际效果进行对比分析,得出通过基于CAAC++的方式调用CATIA自有的干涉检测功能不仅运算速度快、干涉检查信息全,并且程序运行稳定,效果最好,同时应用于开发的四轴数控托架仿真系统,辅助自动钻铆机生产加工,具有较广泛的应用前景。     

综合模块化航电软件仿真测试环境研究

 伴随着综合模块化航空电子(IMA)软件在新一代飞机上的应用,其高复杂性、高度综合的特点以及分层的健康监控和故障管理模式给软件测试提出了挑战。传统的仿真测试环境在应对IMA软件测试中难以满足RTCA DO-178B中规定的对验证过程结果的验证的要求。本文在分析IMA软件特点的基础上,根据DO-178B的要求,综合国外的发展情况和国内的研究进展情况,研究综合模块化航电软件仿真测试环境需求,提出了基于软件故障注入的综合模块化航电软件灰盒仿真测试环境方案,并给出优势分析。该仿真测试环境方案以IMA软件为测试对象,应用软件故障注入技术和代码插装技术满足测试规范文件的要求。其具有通用灵活、适配性强、强实时性等特点,为中国新一代航电软件的系统验证和测试奠定了基础。