Experimental research in rotating wedge-shaped cooling channel with multiple non-equant holes lateral inlet

The heat transfer in a novel smooth wedge-shaped cooling channel with lateral ejection of turbine blade trailing edge is experimentally investigated in both non-rotating and rotating cases. Beside the conventional inlet at the bottom of the channel, an extra coolant injection from 8 lateral non-equant holes is introduced to improve the overall heat transfer. The total mass flow rate ratio (lateral mass flow rate/total mass flow rate) varies from 0 to 1.0. The major inlet Reynolds number and rotation number respectively vary from 10000 to 20000 and from 0 to 1.16. Experimental results show that the lateral inlet decreases local bulk temperature and increases local heat transfer at the middle and the top of the static channel. In rotating cases, the lateral inlet notably improves the heat transfer at the high-radius half channel and compensates the negative effects induced by the rotation. Both intensity and uniformity of heat transfer inside the channel are enhanced while flow resistance decreases with proper mass flow rate ratio of coolant from two inlets. The most satisfactory total mass flow rate ratio is around 2/3. This new structural style of cooling channel has huge potential and provides new direction of heat transfer of turbine blade trailing edge.     

传动比和转速对永磁齿轮传动特性的影响研究

介绍了一种径向调制永磁齿轮，运用有限元技术，通过变更仿真条件中的传动比和转速，并对仿真结果中的输出转矩和传动效率进行分析，从而获得传动比和转速对输出转矩和传动效率的影响规律。结果表明，随着传动比的增大，输出转矩呈二次曲线规律变化，而传动效率则呈减小趋势；相同传动比下，随着主动转子转速的增大，输出转矩和传动效率均呈减小趋势；提出了以传动效率〖WTBX〗η〖WTBZ〗为目标值的等效率曲线概念，得到了η=90%时的等效率曲线i~n₁（i和n₁分别代表传动比和主动转子转速），当n₁和i的交点位于等效率曲线下方时，即可满足η>90%。     

空间太阳能电站姿态运动-结构振动耦合建模与分析

针对多旋转关节空间太阳能电站构型，利用基于能量等效原理的连续体等效方法将其等效为柔性梁模型，并考虑重力梯度影响，建立了姿态运动与结构振动的耦合动力学模型；结合Runge-Kutta 法和Newmark法的优点，提出了适用于求解姿态运动与结构振动耦合动力学方程的改进算法，相比于经典Runge-Kutta 法大幅提高了效率；利用改进算法得到了不同参数下的动力学响应。在此基础上，推导了结构振动量级随结构尺寸的六次方量级增加的规律，仿真结果表明尺寸过大引发不稳定现象；分析了姿态运动和重力梯度对结构振动频率和振幅的影响；发现了姿态运动周期受结构柔性影响而增大的现象，这种现象在低轨以及大初始姿态角下影响更为明显。     

基于薄膜热电堆的新型高温瞬态热流密度传感器的研制

目前针对国内薄膜瞬态热流传感器一致性较差、制备工艺不成熟等问题，提出了一种基于光刻工艺和离子束溅射镀膜工艺的制备方法，200对T型金属薄膜热电偶沉积在10mm×10mm的水冷块上，测量1μm的氧化铝热阻层温差，从而得到瞬态热流密度值。对新型高温瞬态热流密度传感器进行比对法标定，一致性误差为0.211%，即工艺的一致性约为99.79%。实验表明，研制的新型高温瞬态热流密度传感器的一致性好,制备工艺具备良好重复性和可移植性，能够满足高温瞬态热流检测需要，为热流传感器的推广应用及标准化、批量化生产提供了良好的技术支撑。     

推力作用下变质量柔性自旋飞行器稳定性分析

针对变质量柔性自旋飞行器推力作用下稳定性问题，以Timoshenko梁为模型，考虑陀螺效应和剪切效应，基于有限元法建立系统振动方程，分析质量变化、推力作用和自旋转速对系统振动的影响，采用自适应Newmark法求解系统的振动响应。结果表明：质量和推力能够改变固有频率、进动频率和临界转速；受质量变化影响，自旋转速与临界转速相等时，飞行器发生短暂共振，共振响应峰值最大时刻与此重合时刻相比稍有延迟。     

A closed-form nonlinear model for spatial Timoshenko beam flexure hinge with circular cross-section

Beam flexure hinges can achieve accurate motion and force control through the elastic deformation. This paper presents a nonlinear model for uniform and circular cross-section spatial beam flexure hinges which are commonly employed in compliant parallel mechanisms. The proposed beam model takes shear deformations into consideration and hence is applicable to both slender and thick beam flexure hinges. Starting from the first principles, the nonlinear strain measure is derived using beam kinematics and expressed in terms of translational displacements and rotational angles. Second-order approximation is employed in order to make the nonlinear strain within acceptable accuracy. The natural boundary conditions and nonlinear governing equations are derived in terms of rotational Euler angles and subsequently solved for combined end loads. The resulting end load-displacement model, which is compact and closed-form, is proved to be accurate for both slender and thick beam flexure using nonlinear finite element analysis. This beam model can provide designers with more design insight of the spatial beam flexure and thus will benefit the structural design and optimization of compliant manipulators.     

钢筋混凝土梁抗弯刚度公式修正及研究

使用过程中梁的刚度会发生退化,从而影响其使用性能.根据钢筋混凝土的基本性能,分析了各种损伤对刚度退化的影响因素,认为裂缝对刚度的影响最为直接也最为明显.进而从数学角度、物理意义角度对现行规范刚度公式进行分析,并提取出裂缝对刚度退化的影响参数--受拉钢筋应变不均匀系数φ.选择裂缝平均间距和裂缝开展高度作为裂缝统计参数,通过ANSYS有限元软件模拟和分析,建立了关于裂缝统计参数的抗弯刚度修正公式.     

高压球形气瓶焊缝结构设计与焊接工艺

研究了气瓶赤道焊缝区的结构优化设计和焊接工艺改进措施,焊缝区渐变补强设计提高了焊缝区的应变协调性,改进电子束与焊缝作用方式解决了内部飞溅问题,采用优化的电子束工艺参数进行焊接。结果表明:焊接接头质量达到了GJB1718A—2005《电子束焊接》标准Ⅰ级焊缝,焊缝及热影响区力学性能与母材相当,气瓶进行鉴定试验,性能指标满足设计要求。气瓶焊缝结构优化设计,降低了焊缝处应力水平,减少应力集中,通过改进焊接工艺提高了电子束焊缝质量。     

直升机旋翼桨叶打尾梁的成因及预防

建立简化的旋翼模型,对旋翼桨叶锥体动力学作近似分析,确定了直升机桨叶尖部与尾梁间距离的主要影响因素。通过一起旋翼桨叶打尾梁事故,分析了直升机使用过程中旋翼桨叶与尾梁危险接近的原因,并对如何预防上述危险现象的出现进行了探讨。