Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

介质材料对频率选择表面传输特性的影响

通过理论计算和实验验证分析了介质材料对频率选择表面传输特性的影响规律,讨论了蒙皮的厚度、介电常数,芯层厚度、介电常数四个因素对FSS的通带位置、宽度、损耗的影响。结果表明,蒙皮和芯层厚度增厚会使通带位置向低频移动,厚度减小通带位置向高频移动;蒙皮和芯层介电增大会使通带位置向低频移动,介电减小通带位置向高频移动。并测试了同样结构的FSS平板传输特性,理论分析和实验结果一致性较好。     

粗糙表面偏振二向反射分布函数的影响参数及其反演

针对目标偏振二向反射特性研究中模型参数难以准确确定的问题,分析了粗糙表面偏振二向反射分布函数的影响参数,并通过理论推导和仿真计算,研究了各参数对粗糙表面散射特性的作用机理。总结分析了现有参数反演方法,针对现有方法存在的理论缺陷,在P-G(Preist-Germer)模型的基础上,提出了利用"相对偏振分量-角度"的相关关系进行参数反演的方法,设计了参数反演算法,进行了标准反射板和绿漆表面的偏振二向反射特性测试实验,并根据实验数据进行了参数反演和模型验证。实验结果表明,改进的参数反演方法可准确反演所有模型参数。利用反演参数进行模型验证,结果显示模型预测数据与实验数据具有较好的吻合度,验证了模型的准确性。     

NH－93型有机氟涂料的研究

采用国产含氟乳液为基料，研究了辅料的种类和用量，涂料的组成及工艺参数对涂膜性能的影响，提出了能获得良好涂膜的ＮＨ－９３型氟涂料的配方和成膜条件。     

200km/h动力分散型电动旅客列车组车体表面压力分布试验研究

阐述了对我国首列200km/h动力分散型电动旅客列车组(先锋号列车)车体表面压力分布测试情况,对测量结果进行了较为详细的分析,最后用流场计算软件CFX对先锋号列车周围流场进行了数值模拟计算,并将计算结果与测量结果进行了对比,两者有较好的一致性。该研究结果可为空调装置及电器设备冷却风道进排风口位置的选取提供科学依据。     

Radar Imaging of Mercury

Earth-based radar has been one of the few, and one of the most important, sources of new information about Mercury during the three decades since the Mariner 10 encounters. The emphasis during the past 15 years has been on full-disk, dual-polarization imaging of the planet, an effort that has been facilitated by the development of novel radar techniques and by improvements in radar systems. Probably the most important result of the imaging work has been the discovery and mapping of radar-bright features at the poles. The radar scattering properties of these features, and their confinement to permanently shaded crater floors, is consistent with volume backscatter from a low-loss volatile such as clean water ice. Questions remain, however, regarding the source and long-term stability of the putative ice, which underscores the need for independent confirmation by other observational methods. Radar images of the non-polar regions have also revealed a plethora of bright features, most of which are associated with fresh craters and their ejecta. Several very large impact features, with rays and other bright ejecta spreading over distances of 1,000 km or more, have been traced to source craters with diameters of 80–125 km. Among these large rayed features are some whose relative faintness suggests that they are being observed in an intermediate stage of degradation. Less extended ray/ejecta features have been found for some of the freshest medium-size craters such as Kuiper and Degas. Much more common are smaller (<40 km diameter) fresh craters showing bright rim-rings but little or no ray structure. These smaller radar-bright craters are particularly common over the H-7 quadrangle. Diffuse areas of enhanced depolarized brightness have been found in the smooth plains, including the circum-Caloris planitiae and Tolstoj Basin. This is an interesting finding, as it is the reverse of the albedo contrast seen between the radar-dark maria and the radar-bright cratered highlands on the Moon.     

中国空间大功率微波部件微放电抑制表面处理技术最新进展

材料表面的二次电子发射会触发和维持空间高功率射频器件的共振雪崩放电现象,这种现象又被称为微放电效应。微放电效应是限制空间大功率微波部件应用的关键问题之一。从微放电作用的机理出发,首先介绍了两种微放电类型（单表面与双表面）的基本物理机理;然后总结了当前主流的微放电抑制方法并给出各自应用于空间大功率微波部件时的限制。针对空间大功率微波部件微放电抑制的特殊问题,综述了国内近5年来在表面处理法抑制微放电领域的研究成果并预测了微放电抑制技术的发展趋势。     

Validation of non-linear split window algorithm for land surface temperature estimation using Sentinel-3 satellite imagery: Case study; Tehran Province,Iran

In recent years, land surface temperature (LST) has become critical in environmental studies and earth science. Remote sensing technology enables spatiotemporal monitoring of this parameter on large scales. This parameter can be estimated by satellite images with at least one thermal band. Sentinel-3 SLSTR data provide LST products with a spatial resolution of 1 km. In this research, direct and indirect validation procedures were employed to evaluate the Sentinel-3 SLSTR LST products over the study area in different seasons from 2018 to 2019. The validation method was based on the absolute (direct) evaluation of this product with field data and comparison (indirect) evaluation with the MODIS LST product and the estimated LST using the non-linear split-window (NSW) algorithm. Also, two emissivity estimation methods, (1) NDVI thresholding method (NDVI-THM) and (2) classification-based emissivity method (CBEM), were used to estimate the LST using the NSW method according to the two thermal bands of Sentinel-3 images. Then, the accuracy of these methods in estimating LST was evaluated using field data and temporal changes of vegetation, which the NDVI-THM method generated better results. For indirect evaluation between the Sentinel-3 LST product, MODIS LST product, and LST estimated using NSW, four filters based on spatial and temporal separates between pairs of pixels and pixel quality were used to ensure the accuracy and consistency of the compared pairs of a pixel. In general, the accuracy results of the LST products of MODIS and Sentinel-3, and LST estimated using NSW showed a similar trend for LST changes during the seasons. With respect to the two absolute and comparative validations for the Sentinel-3 LST products, summer with the highest values of bias (?1.24 K), standard deviation (StDv = 2.66 K), and RMSE (2.43 K), and winter with the lowest ones (bias of 0.14 K, StDv of 1.13 K, and RMSE of 1.12 K) provided the worst and best results for the seasons in the period of 2018–2019, respectively. According to both absolute and comparative evaluation results, the Sentinel-3 SLSTR LST products provided reliable results for all seasons on a large temporal and spatial scale over our studied area.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.