正十七烷与正十八烷对航空煤油理化性能及液滴平均直径的影响

讨论了正十七烷与正十八烷(C₁₇,C₁₈)对燃料运动黏度、密度、表面张力理化性能的影响,探究了直链烷烃对SMD(Sauter mean diameter)的影响.将Key's混合规律、Tat混合规律和多项式拟合应用于密度公式的拟合,并将Key's混合规律与对数拟合应用于运动黏度公式的拟合,得出的理化性能拟合公式精度较高;通过测量纯煤油及C₁₇,C₁₈混合油雾化的SMD,实验发现随着直链烷烃的质量分数的增加,混合油的运动黏度增加,SMD也随之增加,雾化效果与纯航空煤油的相比较差,而C₁₈混合油的SMD要比C₁₇混合油要大,并且利用密度、运动黏度的拟合公式对SMD进行预测的偏差小于0.3%.      

基于CST方法的高空低雷诺数吸附式叶型耦合优化设计

研究了一种基于类别形状函数变换（CST）方法的吸附式叶型优化设计方法,该方法可以在高空低雷诺数条件下对叶型和抽吸方案耦合优化.结果表明:优化之后在20km高空低雷诺数条件下总压损失降低了65%,静压升提高了0.02,气动性能得到较大提升.而且由于优化过程中罚函数的引入使得优化后吸附式叶型在地面条件下性能也有所提高.对于高空低雷诺数条件下吸附式叶型在抽吸位置之前适当的增加叶型负荷,再通过抽吸来控制附面层,效果最优.并且最佳抽吸位置位于层流分离泡作用区域内.在层流分离泡作用区域内抽吸可以完全消除层流分离泡对叶型性能的影响,并且可以较好控制附面层位移厚度和动量厚度的增加,有效地减小附面层内的动量损失.      

三元乙丙橡胶薄膜黏接界面温度相关性力学性能

采用双悬臂夹层梁(DCSB)试件对三元乙丙橡胶(EPDM)薄膜黏接界面Ⅰ型断裂的温度相关性进行了研究;采用线弹性断裂力学(LEFM)方法获取了黏接界面断裂能,将其与单轴拉伸所得内聚强度作为双线性内聚力模型(CZM)参数,对不同温度条件下双悬臂夹层梁试件的Ⅰ型断裂行为进行了数值仿真.结果表明:仿真与实验曲线偏差较大,偏差出现的原因主要是未经修正的线弹性断裂力学方法所求断裂能存在较大的误差,需对其进行修正.调整模型参数使仿真曲线与实验曲线重合,获取了黏接界面的准确力学性能参数,采用此参数得到的仿真结果与实验结果具有较高的吻合度,证明了模型的可适用性.     

激波矢量控制喷管落压比影响矢量性能及分离区控制数值模拟

激波矢量控制喷管矢量角随落压比(NPR)的增大而下降的现象已被许多研究所证实.对NPR影响矢量角机理及基于多缝腔体和多缝辅助注气方法的分离区控制研究,目标是寻求大NPR条件下矢量性能提高的方法.研究表明:NPR影响矢量角的机理主要由于次流下游近壁面分离区由小NPR时的开放型变为大NPR时的封闭型,从而导致由于壁面压差力产生的矢量力减小所致.多缝辅助注气方法可以有效控制分离区在大NPR时保持开放,注气压力为环境压力时可以在不从系统额外引气的条件下提高矢量性能.      

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

发动机动力模拟风洞试验中的空气桥技术

介绍了发动机动力模拟风洞试验中的空气桥设计技术和影响修正方法.通过自由度分析,选择了合理空气桥布局,采用有限元方法对空气桥关键受力梁进行了优化,建立了空气桥天平一体化数值模拟技术,使得空气桥和天平刚度更加匹配.通过这些设计及优化使得空气桥的作用力最小,并具有较强的克服压力影响、温度影响的能力.通过试验建立了空气桥附加刚度影响、内部压力影响、温度影响和内部流量影响的修正方法,进一步减小了空气桥对天平的影响.在8m×6m低速风洞进行了某大展弦比飞机全模涡扇动力模拟器(TPS)短舱动力模拟试验.试验结果重复性好,阻力系数精度达到0.0003,和相关文献吻合.这表明空气桥技术是成功的,满足了TPS短舱动力模拟试验要求.      

机载燃油惰化技术及标准研究

针对目前广泛应用于飞机燃油箱起火和爆炸防护的机载燃油惰化系统,详述了国外机载燃油惰化技术的发展历程,并介绍了国内发展现状,提出影响机载燃油惰化系统设计的关键因素。在此基础上,简述了国内外标准情况,提出了制定我国机载燃油惰化系统标准的建议。     

浅谈基于IPDT的民用飞机重量控制技术

在民机研制过程中,有效地实施重量控制对于项目的成功非常关键。飞机超重不仅会导致设计和运营成本的增加,也将无法实现既定的商载和航程等设计指标。从各部门与重量控制工作的联系出发,结合某型民用飞机的设计实践,介绍了产品联合研发团队(IPDT)模式下重量控制的工作内容、工作流程和常用的减重方法,为民机的重量控制工作提供借鉴和参考。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.