基于FDDPB方法的卫星姿态控制系统故障诊断

针对卫星姿态控制系统故障诊断问题,将执行机构及输出传感器的阶跃型和缓变型输出偏差统归于一种"参数偏差"型故障,介绍了改进的参数偏差型故障的实时检测与诊断 (FDDPB,Fault Detection and Diagnostics of Parameter Bias)算法,说明了此算法在卫星姿态控制系统执行机构和传感器故障诊断中的应用.引入卫星姿态动力学模型和飞轮模型,建立了算法仿真模型,选取执行机构阶跃型和缓变型故障作为故障注入条件,将该算法用于实验验证.仿真结果表明:该算法能够检测出系统发生的故障,且能够准确估计出故障幅值.      

基于长短时记忆神经网络(LSTM)的钟差预报算法

原子钟钟差预报在原子时计算和原子钟频率驾驭中发挥着重要的作用。长短时记忆神经网络（LSTM）预报算法能够处理多参数长期依赖关系的时间序列预报,以氢钟和铯钟实测数据为样本,通过构建LSTM钟差预报模型,降低了长期原子钟内部噪声以及原子钟漂移对钟差预报的影响,并以72h,240h和720h为预报时长,分别与线性多项式模型、灰色模型和Kalman模型原子钟钟差预报模型进行预报误差对比。研究表明,在240h以上的预报时长中,LSTM建模长期依赖关系的优势得以体现,相较于其他3类模型可以获得更高的预报精度。     

异构多星编队的脉冲构型保持控制方法

近地轨道的双星编队通常设计具有自稳定性的编队构型参数初值,通过保持编队构型参数形成长期稳定的相对周期运动。针对编队中卫星数量增多产生的相对运动耦合问题,提出了基于Hill坐标和三角函数公式的多星相对运动分析方法。基于SAR载荷测量基线定义,结合多星编队构型参数的相对运动特性,提出了编队构型参数的设计方法,能够实现多星编队的最大有效基线组合。通过分析J2项摄动和大气阻力摄动的长期影响,研究了异构多星编队的相对运动衍化规律,提出了主从形式的脉冲偏置控制,能够有效保持针对异构多星编队设计的编队构型。通过面质比异构的四星编队控制仿真,验证了脉冲偏置控制形式下异构多星编队构型保持控制方法的有效性。     

利用能量/动量飞轮的偏置动量姿态控制系统

研究偏置动量姿态控制系统中的集成能量与姿态控制问题。利用一对正 反转飞轮提供偏置角动量并同时储 /放能以满足星载设备的能源需求。滚动 /偏航运动由俯仰轴磁矩控制。设计了力矩形式的飞轮的控制律 ,使之提供期望的俯仰控制力矩 ,并以给定的功率储 /放能。保持两只飞轮正 反转可以完全避免飞轮控制律中的系统奇异。提出了利用动能反馈的飞轮储能功率规划方案 ,以使系统维持能量平衡 ,避免由于能量过剩引起的飞轮饱和。飞轮的最小转动惯量受最大偏置角动量和最小能量的限制 ,结合几何方法对这种限制条件进行了分析。数值仿真结果证明了控制方案的有效性。     

PIC检测器解析表达式的偏差修正

由于传统PIC(Parallel Interference Canceller,并行干扰消除)检测器性能分析公式存在偏差,导致与仿真结果有一定的差异,不能准确反映系统性能。在对传统PIC检测器性能表达式和推导过程存在的偏差进行分析的基础上,通过公式推导,得到更为精确的PIC检测器任一级的误码率性能解析表达式。通过数值计算,偏差修正后的解析表达式对误码率估计的准确度比修正前提高了1个数量级,与仿真结果更为接近,并且干扰消除的级数越多效果越好。研究结果表明,修正后的PIC解析表达式是有效的。     

BDS-3 PPP模糊度固定实现及精度评估

精密单点定位(PPP)模糊度固定(AR)能够显著提升精密定位的收敛速度和精度。通过在BDS-2和BDS-3之间添加系统间偏差的方法实现BDS-3的模糊度固定,并基于全球MGEX测站静态、仿动态数据和车载实验数据全面评估了BDS-3模糊度固定的效果。结果表明,相对于浮点解,BDS-3 PPP模糊度固定能够显著提升PPP的精度,在东北天3个方向上静态解算精度提升依次为37.4%、26.2%和20.1%;仿动态解算精度提升依次为38.3%、27.2%和11.1%;车载动态实验BDS-3模糊度固定精度在三维方向上综合提升为40.4%。此外,模糊度固定后,以浮点解稳定后的两倍定位精度为基准,在东北天方向上,静态定位时间提升程度依次为63.5%、64.0%和40.3%;仿动态定位时间提升程度依次为58.7%、56.8%和25.4%;车载实验在三维方向的收敛时间为30.0 min。以上结果证明了所提方法的有效性及BDS-3模糊度固定的性能提升。     

一种弹性胶粘剂在石英加速度计中的应用

针对石英加速度计偏值问题,提出了摆片组粘接胶粘剂的选用原则,并应用有限元软件进行了仿真研究.分析结果表明,固化后弹性模量小的胶粘剂粘接面产生的应力较小,有利于提高石英加速度计偏值的稳定性.进一步对选用的弹性胶粘剂进行了强度检测,测试结果表明石英加速度计的偏值稳定性得到了明显改善.     

Fast calibration of between-receiver GPS/Galileo/BDS differential phase bias with millimeter accuracy based on short baseline mode

The differential code and phase biases induced by the receiver hardware (including receiver, antenna, firmware, etc.) of the Global Navigation Satellite System (GNSS) have significant effects on precise timing and ionosphere sensing, thus deserve careful treatment. In this contribution, we propose an approach to fast fix the single-difference ambiguity to finally obtain the unbiased estimates of between-receiver differential phase bias (BR-DPB) and between-receiver differential code-phase bias (BR-DCPB) based on the short baseline mode. The key to this method is that the error sources can be significantly eliminated due to the length of the baseline is very short. At the same time, the empirical constraints and random characteristics of BR-DPB/BR-DCPB were considered, which is conducive to the resolution of single-difference ambiguity. Several sets of GNSS data (GPS L1/L2, Galileo E1/E5b, and BDS B1/B3), recorded by the short baselines in an interval of 30 s and covered a broad range of receiver/antenna types (JAVA, SEPT, LEIC, and TRIM), were used to verify the effectiveness of the proposed method. The numerical tests show that the proposed method is capable of fast fixing the single-difference ambiguity successfully within a few epochs and then providing the unbiased estimates of BR-DPB and BR-DCPB in an epoch-by-epoch manner. Experiments show that the estimated BR-DPB is in millimeter accuracy, which is of great significance for the millimeter-accuracy phase time transfer and ionospheric delay estimation. Furthermore, the calibrated BR-DPB/BR-DCPB can be treated as the known products for long-distance precise timing and ionosphere sensing based on the inter-station single-difference model.     

Evaluation of rapid phase clock/bias products for PPP ambiguity resolution and its application to the M7.1 2019 Ridgecrest,California earthquake

Precise point positioning with ambiguity resolution (PPP-AR) is a useful tool for high-precision geodetic and geophysical applications, while phase bias products are the prerequisite to implement PPP-AR. Wuhan University has been providing the final (the best operationally post-processing solution based) phase clock/bias products with a latency of two weeks since March of 2019, while a dedicated open-source software package PRIDE PPP-AR is released to leverage these products for high-precision positioning. In order to satisfy some both time and precision critical applications, such as rapid earthquake response, Wuhan University also released rapid (with comparable quality but with much shorter delivery latency) phase clock/bias products with a latency of less than 24 h and updated PRIDE PPP-AR in July 2019. We first introduce the phase clock/bias generation and validation schemes and the maintenance of routine products provision. Then, with 14 days (July 2 to July 15 in 2019) of GPS data collected from 146 globally distributed IGS (International GNSS Service) stations, we evaluated the positioning performance of the rapid products with respect to their final counterparts. It is found that positioning precision of PPP-AR using rapid products is comparable to that using final products, especially in kinematic positioning mode. When rapid products are used, the RMS of PPP-AR in static mode with respect to IGS weekly solutions can reach 1.7 mm, 1.8 mm and 5.5 mm in the east, north and up components, respectively. Furthermore, the RMS of epoch-wise positions with respect to daily solutions for the east, north and up components are 0.51 cm, 0.57 cm and 1.51 cm for PPP-AR with rapid products in kinematic mode. It demonstrates that the rapid phase clock/bias products can sufficiently meet the precision requirement of most geodetic and geophysical applications yet with much shorter time delay. Finally, we study the July 6th M7.1 2019 Ridgecrest, California earthquake using the rapid phase clock/bias products and demonstrate their comparable performance against the final products.     

Estimation of differential code biases with Jason-2/3 onboard GPS observations

With the continuous deployment of Low Earth Orbit (LEO) satellites, the estimation of differential code biases (DCBs) based on GNSS observations from LEO has gained increasing attention. Previous studies on LEO-based DCB estimation are usually using the spherical symmetry ionosphere assumption (SSIA), in which a uniform electron density is assumed in a thick shell. In this study, we propose an approach (named the SHLEO method) to simultaneously estimate the satellite and LEO onboard receiver DCBs by modeling the distribution of the global plasmaspheric total electron content (PTEC) above the satellite orbit with a spherical harmonic (SH) function. Compared to the commonly used SSIA method, the SHLEO model improves the GPS satellite DCB estimation accuracy by 13.46% and the stability by 22.34%, respectively. Compared to the GPS satellite DCBs estimated based on the Jason-3-only observations, the accuracy and monthly stability of the satellite DCBs can be improved by 14.42% and 26.8% when both Jason-2 and Jason-3 onboard observations are jointly processed. Compared with the Jason-2 solutions, the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations have an improved consistency of better than 18.26% and 9.71% with the products provided by the Center for Orbit Determination in Europe (CODE) and Chinese Academy of Sciences (CAS). Taking the DCB products provided by the German Aerospace Center (DLR) as references, there is no improvement in accuracy of the GPS satellite DCB estimates based on the fusion of Jason-2 and Jason-3 observations than the Jason-2 solutions alone. A periodic variation is found in the time series of both the Jason-3 and Jason-2 onboard receiver DCB estimates. Preliminary analysis of the PTEC distribution based on the estimated SH coefficients are also presented.