复合推进剂侵蚀燃烧特性的κ-ε参数表征

本文从推进剂侵蚀燃烧机理分析出发,综合片型装药发动机中止燃烧试验与相应的燃烧室内流场N-S方程组STMPLE方法数值分析的特点,导出一种由燃面上k~2/ε和p参数表述推行剂侵蚀特性的新方法,并成功地应用于4B丁羟复合药侵蚀特性的研究中.     

Accuracy enhancement of the spherical actuator with a two-level geometric calibration method

This paper presents a two-level geometric calibration method for the permanent magnet （PM） spherical actuator to improve its motion control accuracy. The proposed actuator is com- posed of a stator with circumferential coils and a rotor with multiple PM poles. Due to the assembly and fabrication errors, the real geometric parameters of the actuator will deviate from their design values. Hence, the identification of such errors is critical for the motion control tasks. A two-level geometric calibration approach is proposed to identify such errors. In the first level, the calibration model is formulated based on the differential form of the kinematic equation, which is to identify the geometric errors in the spherical joint. In the second level, the calibration model is formulated based on the differential form of torque formula, which is to calibrate the geometric parameters of the magnetization axes of PM poles and coils axes. To demonstrate the robustness and availability of the calibration algorithm, simulations are conducted. The results have shown that the proposed two-level calibration method can effectively compensate the geometric parameter errors and improve the positioning accuracy of the spherical actuator.     

民机防冰系统自然结冰试飞技术研究

结合某型民机自然结冰条件下防冰系统的试飞,对试飞所需的测试改装工作进行了总结,并对试飞前需进行的各种安全性评估进行了总结说明,明确了试飞中需考虑的各种构型情况,提出一套循序渐进的自然结冰试飞方法。同时提出了试飞中结冰气象参数的可接受性判据,最后针对自然结冰试飞中结冰气象参数的处理提出了分段等效处理的方法。     

A systematic approach to nonlinear rotorcraft model identification

The development of a powerful parameter estimation routine and its integration into the simulation environment HOST is described. With this tool approaches are being made towards new strategies of mathematical modeling, aimed at providing highly accurate and nevertheless run-time efficient simulation models. The identification routine is capable of optimizing parameterized models in both dynamic time domain simulation and static (e.g. trim state variation) conditions. Examples of both cases are presented to emphasize the improvement in the system response prediction and to demonstrate the abilities of the identification techniques in combination with the nonlinear simulation platform. This article reviews the activities and achievements accomplished by the DLR Institute of Flight Research and the ONERA Systems Control and Flight Dynamics Department during the last few years in the research on rotorcraft flight dynamics modeling and model identification. Future activities that require extensive high fidelity modeling are in the scope of the current and coming modeling activities that include the use of the presented methods and software technologies.     

挠性空间结构的H∞辨识

重点研究挠性空间结构的Ｈ∞辨识，研究表明：依据系统的输入输出空间，对系统的未知动力学参数估计和对高维数截断的适当操作，将导致适合于控制的低维数学模型。模型维数确定时，系统模型与实际系统的距离在Ｈ∞范数的意义下几乎为最小，模型维数足够大时，系统模型与实际系统的距离可任意小，这是文下间提出了挠性空间结构Ｈ∞辨识的基本思想，为此，以带挠性梁的卫星系统为背景，首先分析了系统的动力学特性，引入了挠性系统Ｈ∞     

预置接触区长度系数的Spirac切齿调整计算方法

基于参考点处瞬时接触椭圆大体决定接触区长度的方法,提出一种切齿调整计算方法.根据奥利康刀倾半展成法(Spirac)切齿原理,建立摆线齿准双曲面齿轮的数学模型,得到了大轮齿面参考点处瞬时接触椭圆参数;在满足参考点位置、压力角和螺旋角的基础上,将刀倾角也作为迭代变量,并将接触区长度系数等于预置值作为新增的迭代条件,迭代求解切齿调整参数.最后以一对摆线齿准双曲面齿轮副为例,对比该方法与Spirac切齿调整计算结果,验证了该方法的准确性,并对不同预置接触区长度系数得到的齿面进行齿面接触分析.结果表明,该方法解决了反复调整刀倾角的问题,并通过精确控制大轮齿面接触区长度系数等于设计值,实现了对大轮齿面接触区长度的预控.     

涡扇发动机性能退化缓解控制与推力设定

为了补偿性能退化发动机的推力损失,减轻飞行员工作负担,提高推进系统的自动化程度,开展了涡扇发动机性能退化缓解控制(EPDMC)研究。针对某型涡扇发动机部件级模型设计了具备稳态控制、加/减速过渡态控制和极限保护等功能的基准控制器;在此基础上设计了外环推力控制回路,给出1种在多参数约束下的推力设定方法,并设计了合理的切换逻辑确保内外环控制器能协调工作。MATLAB/Simulink下的仿真结果表明:该智能改进控制系统架构可以在保证发动机安全工作的前提下,通过合理地设定期望推力,最大程度地补偿推力损失,维持油门杆角度和推力的对应关系近似不变。     

Spatial transformation of general sampling-aliasing frequency region for rotating-blade parameter identification with emphasis on single-probe blade tip-timing measurement

Blade-health monitoring is intensely required for turbomachinery because of the high failure risk of rotating blades. Blade-Tip Timing (BTT) is considered as the most promising technique for operational blade-vibration monitoring, which obtains the parameters that characterize the blade condition from recorded signals. However, its application is hindered by severe undersampling and stringent probe layouts. An inappropriate probe layout can make most of the existing methods invalid or inaccurate. Additionally, a general conflict arises between the allowed and required layouts because of arrangement restrictions. For the sake of economy and safety, parameter identification based on fewer probes has been preferred by users. In this work, a spatial-transformation-based method for parameter identification is proposed based on a single-probe BTT measurement. To present the general Sampling-Aliasing Frequency (SAFE) map definition, the traditional time–frequency analysis methods are extended to a time-sampling frequency. Then, a SAFE map is projected onto a parameter space using spatial transformation to extract the slope and intercept parameters, which can be physically interpreted as an engine order and a natural frequency using coordinate transformation. Finally, the effectiveness and robustness of the proposed method are verified by simulations and experiments under uniformly and nonuniformly variable speed conditions.     

一种高精度夹具的设计原理

通过对定位精度高达２μｍ,又非常便捷装卸的瑞士ＥＲＯＷＡ夹具结构原理的介绍,以引起国内同行的关注,旨在推广应用于我国航空精密零件及工模具生产中,以期解决长期困惑我国的高位置精度问题。     

铝颗粒云燃烧研究进展

为探究铝颗粒云燃烧特性,把握其研究进展,并为后续研究工作提供参考,本文首先简述了铝颗粒点火、燃烧过程,总结了铝颗粒燃烧机理;其次,综述了铝颗粒云燃烧的实验、理论和模拟研究进展,从不同维度分析了影响颗粒云火焰速度的关键参数,并提出颗粒云燃烧的研究方向,包括提升颗粒云燃烧实验颗粒分散均匀性与表征精度、降低火焰传播速度等实验结果散差、改善颗粒云燃烧理论预测模型精度及构建实用的颗粒云燃烧模拟CFD模型。