基于铣抛喷组合工艺的TB6钛合金精铣参数优化

TB6钛合金是航空制造领域承重结构件的重要材料,属于典型难加工材料。开展了TB6钛合金铣抛喷组合工艺试验,研究了不同铣削参数对表面完整性的影响及精铣与喷丸工序间的耦合关系。结果表明,试件表面粗糙度主要受铣削每齿进给量fz影响。fz0.2mm/z时,组合工艺加工后,试件表面粗糙度值Ra较低;fz0.2mm/z时,随精铣fz提高,铣削硬化率下降,喷丸后的表面粗糙度提高;铣喷组合工艺条件下,铣削线速度vs在20~40m/min范围内,硬化率随vs的升高而降低,喷丸区域表面粗糙度升高;vs在40~50m/min范围内,铣削硬化率升高,喷丸区域表面粗糙度降低。切宽ae对试件硬化和表面粗糙度的影响不显著。铣喷组合工艺条件下的精铣参数优化结果为:vs=50m/min,fz=0.2mm/z,ae=1.0mm。铣抛喷组合工艺条件下,可在低于0.4mm/z范围内适当提高铣削每齿进给量fz。     

多维系统测量的误差分析计算

多维系统测量参数众多,系统误差分析比较复杂。本文归纳给出多维系统测量误差分析计算方法措施,并给出算例。     

地面力学在火星壤力学参数估计研究中的 进展与展望

掌握火星土壤的力学参数是保障火星车顺利完成巡视探测的关键。通过对已成功开展的火星巡视探测任务进行汇总，探讨了复杂火星地貌对火星车移动性能的影响，分析了基于地面力学理论的火星土壤力学参数估计方法，包括：基于车轮的火星壤在轨力学参数估计方法和基于轮壤力学模型的力学参数辨识方法。最后，对未来关于地面力学在星壤力学参数评估进行了探讨。     

基于PI控制的直流电机调速控制系统的研制

为解决直流电机速度控制问题,采用增量式PI控制方法,设计了无刷直流电机速度控制器。对模拟调节器进行了离散化处理,每隔10ms用编码器测速一次,并进行适当的软件滤波,用计算出速度差作为控制量,用离散的差分方程代替连续的微分方程,用软件实现了PI控制算法。搭建了基于STM32的实验平台,给出了P和I参数整定方法,并通过大量实验得到了合适的P和I的系数,验证了该增量式PI控制方法的正确性。研究结果表明:该PI控制算法能够实现对速度的恒定控制,响应速度快、抗干扰能力强。为PID控制提供了实验的方法和步骤。     

Modeling spatial density in low earth orbits using wavelets and random search

The events that occurred after 2007 such as Chinese anti-satellite test, explosion of Briz-M upper stage, break up of cosmos-2421 and collision of cosmos-2251 with Iridium-33 satellites have completely changed the spatial density patterns in low earth orbits. This has increased the risk of collision between active satellites and debris created by them. Aftermath, the risk assessment of possible collisions called as conjunction analysis of working satellites from day to day has become more crucial. Spatial density models are useful in understanding the long-term likelihood of a collision in a particular region of space and helpful in pre-launch orbit planning. In this paper we present an algorithmic procedure for automatically estimating exact model parameters corresponding to the peak location and number of peaks using wavelets that will speed up the parameter estimation process for the models with peaks.     

FrFT-CSWSF:Estimating cross-range velocities of ground moving targets using multistatic synthetic aperture radar

Estimating cross-range velocity is a challenging task for space-borne synthetic aperture radar（SAR）, which is important for ground moving target indication（GMTI）. Because the velocity of a target is very small compared with that of the satellite, it is difficult to correctly estimate it using a conventional monostatic platform algorithm. To overcome this problem, a novel method employing multistatic SAR is presented in this letter. The proposed hybrid method, which is based on an extended space-time model（ESTIM） of the azimuth signal, has two steps： first, a set of finite impulse response（FIR） filter banks based on a fractional Fourier transform（FrFT） is used to separate multiple targets within a range gate; second, a cross-correlation spectrum weighted subspace fitting（CSWSF） algorithm is applied to each of the separated signals in order to estimate their respective parameters. As verified through computer simulation with the constellations of Cartwheel, Pendulum and Helix, this proposed time-frequency-subspace method effectively improves the estimation precision of the cross-range velocities of multiple targets.     

用标准滚刀滚切短圆柱齿轮的探讨

同一条件下，短齿圆柱齿轮的强度较高，本文介绍一种简单而实用的加工方法，在普通滚齿机上滚切短齿圆柱齿轮。     

使用C6000 McBSP实现SPI接口的方法研究

介绍了将C6000的McBSP接口配置为SPI接口主控设备的方法和步骤,并通过对一种SPI接口串行FLASH芯片访问,验证了设计的正确性.解决了McBSP的初始化配置以及数据接收的问题.该设计有助于简化嵌入式计算机的局部设计.     

排气液化发动机高速液化装置研究

为简化涡轮排气液化发动机蒸汽液化装置的结构、缩小体积，提出了基于超声速汽液两相流升压原理的水蒸气液化方案，建立了考虑多因素的数学方程式，讨论了水蒸气喷嘴段结构参数、混合室参数、扩压段参数和混合室阻力等对升压能力的影响。计算结果表明：收敛-扩张式升压液化装置的升压系数大于3。     

温度冲击试验箱的参数测量

简介了温度冲击试验原理，提供了一种测量温度冲击试验设备参数的方法，并分析了一个实例。