基于SP-ABC算法的数控铣削参数优化

针对铣削加工中成本最低的优化问题,采用一种改进的人工蜂群(SP-ABC)算法对铣削参数进行优化.在基本ABC算法的基础上,嵌入粒子群(PSO)算法,以提高算法的局部寻优能力.此外,不同于传统的单工序优化,建立的优化目标模型,在考虑实际生产过程中的各种约束条件下,可同时对粗、精两个阶段多道工序同步进行优化.计算机仿真结果表明,相较其他的基本算法,该算法能够找到更优的铣削参数组合,从而实现铣削加工过程的成本最低化.     

基于支持向量机和粒子群算法的钛合金铣削加工参数优化

钛合金材料在加工过程中受铣削力影响易于产生变形而影响加工效果,为保证加工质量,提高生产效率及降低加工成本,研究切削加工参数的合理选择非常重要.对钛合金材料Ti6Al4V铣削加工进行有限元数值计算,结合试验设计方法构建了基于支持向量机的切削力预测模型,以材料去除率为优化目标,提出了一种基于支持向量机和粒子群算法的优化方法,对钛合金铣削加工参数进行了优化.结果表明,该方法准确、高效、可行,为钛合金加工工艺参数优化提供一种新的方法,具有良好的推广价值.     

低轨卫星月影事件预报优化

针对卫星月影问题,提出了一种低轨卫星优化的月影预报策略,可以有效提高目前低轨卫星在轨管理时对月影事件预报的效率.结合仿真对产生月影事件的太阳、地球、月球的三体关系进行了分析,首先给出了月影产生的解析分析方法,并通过对一个三维月影影响模型的分析,得到了月影影响区间的判定要素——月影临界角;然后进一步通过对月影临界角的分析,提出了基于太阳与白道面的位置关系和月影临界角对低轨卫星月影事件的优化预报方法;最后基于大量的随机低轨卫星场景对本方法的正确性进行了验证.研究结果表明,此方法能够较大地提高月影预报效率,可以将月影预报频率从每月1次降低到每年2次,从而简化了低轨卫星在轨运行管理的任务复杂度,为卫星的在轨可靠运行提供支持.     

基于Fibonacci搜索方法的航空发动机性能寻优

介绍了Fibonacci搜索方法应用于发动机性能优化中的原理,建立带两个出口面积、气流马赫数可变的引射器的涡喷发动机的总体性能计算模型,应用Fibonacci搜索方法在优化参数区间内对该发动机进行了最大推力、最低油耗、最低涡轮前温度模式的寻优.举例说明了Fibonacci搜索方法应用的具体过程.给出了不同高度、马赫数下的寻优结果.结果表明:最优目标性能满足的约束边界与飞行高度、马赫数密切相关.不同的飞行高度、马赫数对应了不同的最优控制策略.但不论飞行任务如何,根据该方法进行的优化控制所获得的目标性能是最佳的.该优化方法不仅适用于该类涡喷发动机,也为其他类型航空发动机的优化控制打下一定的基础.      

基于离散粒子群算法的航空发动机总装工艺优化方法

为了提高航空发动机总装工作的效率与质量,加强对总装工序和总装机件的管控,量化不同总装人员工作任务量,提高发动机总装的一致性和可追溯性,提出了1种发动机总装分区优化方法。以改进的2进制粒子群算法为基础,平衡了发动机总装各区域的工作内容,最小化各总装区域的工作差异,增强了每个区域装配机件的关联度,提高了总装工作的并行度,从而提高了装配质量。以某型发动机总装区域划分工作为实例,通过上述算法进行了总装区域划分,量化了所有装配区域每一工序的具体装配内容,减小了不同装配区域间的机件差异,杜绝了缺件、剩件等装配问题。     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

基于拓扑优化和形状优化的桨叶结构设计

直升机旋翼桨叶剖面结构设计是研究旋翼动力学设计的基础。提出一种联合拓扑优化和形状优化的 两级优化设计方法,可用于桨叶剖面结构的设计。第一级优化以变密度法(SIMP)作为拓扑优化的材料插值方 法,以桨叶体积最小化为设计目标,约束桨叶节点位移和应力,建立桨叶的拓扑优化求解模型;第二级优化以重 构的桨叶模型为基础开展形状优化,降低局部应力集中以及找到合理的边界节点位置。对优化后的模型进行 有限元分析,结果表明:通过拓扑优化和形状优化的两级优化,能够得到满足强度和稳定性要求的结构布局,为 桨叶结构设计提供指导方案。     

A review of topology optimization for additive manufacturing: Status and challenges

Topology optimization was developed as an advanced structural design methodology to generate innovative lightweight and high-performance configurations that are difficult to obtain with conventional ideas. Additive manufacturing is an advanced manufacturing technique building as-designed structures via layer-by-layer joining material, providing an alternative pattern for complex components. The integration of topology optimization and additive manufacturing can make the most of their advantages and potentials, and has wide application prospects in modern manufacturing. This article reviews the main content and applications of the research on the integration of topology optimization and additive manufacturing in recent years, including multi-scale or hierarchical structural optimization design and topology optimization considering additive manufacturing constraints. Meanwhile, some challenges of structural design approaches for additive manufacturing are discussed, such as the performance characterization and scale effects of additively manufactured lattice structures, the anisotropy and fatigue performance of additively manufactured material, and additively manufactured functionally graded material issues, etc. It is shown that in the research of topology optimization for additive manufacturing, the integration of material, structure, process and performance is important to pursue high-performance, multi-functional and lightweight production. This article provides a reference for further related research and aerospace applications.     

多变量全局寻优与智能优化在星座组网中的应用

顶层任务规划通常与星座组网紧密结合,小卫星分散灵活的特性尤其适用于星群规模化在轨运行。针对热点区域覆盖和全球覆盖的不同任务需求,提出了对构型多变量进行全局寻优和利用智能优化技术进行星座构型优化的方法,两种优化方法可分别获得小规模星群最优效能与超大型星群的较优效能。优化方法不受轨道类型和任务目标分布的约束,具有良好的鲁棒性。     

100 kWe级空间快堆核电源系统仿真平台开发与应用

空间核反应堆电源作为一种具有竞争力的空间电源方案,正逐渐受到关注及应用。本文针对一个100 kWe级锂冷快堆耦合布雷顿循环的空间堆核动力系统方案,修改了RELAP5程序中的物性程序、换热模型,程序中的中子动力学模块使用蒙特卡洛方法计算快堆物理参数与堆芯控制调节参数,由此集成并建立一个空间快堆核动力系统综合仿真平台,应用该平台对100 kWe级空间堆核动力系统进行了稳态模拟与事故分析。结果表明:在瞬态发生后系统各参数变化符合预期,验证了各部件及控制系统的功能性及有效性;同时,还初步进行了仿真平台用于100 kWe级空间反应堆核动力系统设备的设计优化的实践,为空间快堆设计与安全分析提供了技术储备。