Spatial transformation of general sampling-aliasing frequency region for rotating-blade parameter identification with emphasis on single-probe blade tip-timing measurement

Blade-health monitoring is intensely required for turbomachinery because of the high failure risk of rotating blades. Blade-Tip Timing (BTT) is considered as the most promising technique for operational blade-vibration monitoring, which obtains the parameters that characterize the blade condition from recorded signals. However, its application is hindered by severe undersampling and stringent probe layouts. An inappropriate probe layout can make most of the existing methods invalid or inaccurate. Additionally, a general conflict arises between the allowed and required layouts because of arrangement restrictions. For the sake of economy and safety, parameter identification based on fewer probes has been preferred by users. In this work, a spatial-transformation-based method for parameter identification is proposed based on a single-probe BTT measurement. To present the general Sampling-Aliasing Frequency (SAFE) map definition, the traditional time–frequency analysis methods are extended to a time-sampling frequency. Then, a SAFE map is projected onto a parameter space using spatial transformation to extract the slope and intercept parameters, which can be physically interpreted as an engine order and a natural frequency using coordinate transformation. Finally, the effectiveness and robustness of the proposed method are verified by simulations and experiments under uniformly and nonuniformly variable speed conditions.     

发动机故障诊断的变记忆约束滤波算法

为提高故障诊断可靠性,给出了3种利用多次测量信息减少测量误差影响的方法,即变记忆约束滤波算法、分段算术平均预平滑算法以及指数顶平滑算法。其中,变记忆约束滤波算法能够有效地避免由于故障方程多重共线性所引起的病态解。证明了多故障诊断问题中滤波算法与分段算术平均算法的等价性,证明了在衰减滤波的条件下（第一变记忆因子小于1）,随测量点数的增加,变记忆滤波算法的第一变记忆因子与指数平滑的平滑系数之和趋近于1。利用计算机仿真方法对于所得结论进行了检验。     

铝颗粒云燃烧研究进展

为探究铝颗粒云燃烧特性,把握其研究进展,并为后续研究工作提供参考,本文首先简述了铝颗粒点火、燃烧过程,总结了铝颗粒燃烧机理;其次,综述了铝颗粒云燃烧的实验、理论和模拟研究进展,从不同维度分析了影响颗粒云火焰速度的关键参数,并提出颗粒云燃烧的研究方向,包括提升颗粒云燃烧实验颗粒分散均匀性与表征精度、降低火焰传播速度等实验结果散差、改善颗粒云燃烧理论预测模型精度及构建实用的颗粒云燃烧模拟CFD模型。     

一种双时间尺度函数Wiener过程性能退化模型

为通过性能退化数据评估产品的可靠性,基于广义Wiener过程提出了一种双时间尺度函数模型以描述产品退化过程。采用极大似然估计(MLE)法求解模型参数,推导了其寿命分布(FTD),进而进行可靠度分析和寿命评估。对模型进行了Monte Carlo模拟验证和实例应用,并将目前常用的混合效应Wiener过程模型作为参考方法进行了对比分析。结果表明:根据90%可靠度曲线的定义,该方法较参考方法的结果更为合理、准确。进一步的寿命评估结果表明,该方法与参考方法的平均寿命相差232.9h,90%可靠寿命结果相差109.4h,且参考方法计算结果偏于危险。      

Inertial parameter estimation and control of non-cooperative target with unilateral contact constraint

In this paper, the relative sliding motion between the target and the manipulator’s end-effector is considered and characterized as a unilateral contact constraint. A new possible solution is presented to estimate the inertial parameters of a non-cooperative target while the relative sliding motion exists. First, the detailed analysis of the dynamical model is presented, and a parameter-explicit linear time-varying model is obtained. Then, an extended state observer is constructed based on the new model, which can effectively estimate the unknown inertial parameters of the target when relative sliding motion exists. As the modified reactionless controller requires the knowledge of inertial parameters, a hybrid post-capture control scheme is also established based on the switch law between different controllers. The correctness and efficiency of the proposed algorithm are validated by numerical simulation, which proves a potential framework for the non-cooperative target post-capture operation.     

Parameter studies and evaluation principles of delamination damage in laminated composites

Delamination represents one of the most severe failure modes in composite laminates, especially when they are subjected to uniaxial compression loads. The evaluation of the delamination damage has always been an essential issue of composite laminates for durability and damage tolerance in engineering practice. Focusing on the most typical and representative elliptical delamination issue, an analytical model simultaneously considering the conservative buckling process and non-conservative delamination propagation process is implemented. Various computational cases considering different delamination depths, directions, aspect ratios, and areas are established, and the predicted results based on the analytical model are carefully compared. Effects of these geometrical delamination parameters on the buckling, delamination propagation, and failure behaviors of composite laminates are thoroughly analyzed, and innovative evaluation principles of the delamination damage have been concluded. It is found that the delamination area is the key factor that truly affecting the failure behaviors of delaminated composites, and the local / global buckling and failure loads show clear linearity with the delamination area, whilst the delamination depth and direction only have slight effects.     

控制力矩陀螺磁悬浮转子的指数趋近积分滑模控制研究

针对微重力、动框架等多源扰动下磁悬浮控制力矩陀螺磁轴承转子系统的强非线性、参数摄动及未建模动态等问题,开展控制力矩陀螺的磁轴承转子鲁棒控制研究。建立了磁轴承转子轴向通道动力学模型与电磁力工作点线性化模型,分析了系统参数摄动及未建模动态,并在此基础上提出了一种非线性系统指数趋近积分滑模控制方法,设计了含有电流及位移的积分滑模平面,采用指数趋近律与饱和函数抑制抖振实现到达阶段滑模控制律。实验结果表明：采用该方法可有效抑制滑模的抖振现象,参数摄动时系统具有较佳动态性能,同时在转子转动、框架工作时保证系统良好鲁棒性。     

飞轮扰动经验模型参数的识别与改进

对飞轮扰动模型参数的精确识别是研究光学卫星高稳定度、高分辨率成像的基础. 目前, 飞轮的扰动模型识别主要有两种: 经验模型和分析模型. 经验模型需要识别的参数是谐波级数和幅值系数, 而当前存在的参数识别算法忽略了时域截断的影响, 导致幅值系数识别存在较大偏差, 这会引起扰动响应分析的不确定性. 针对上述情况, 提出了窗函数法和与其相关的频域恢复技术, 有效弥补了时域截断的影响. 通过实验仿真结果可见, 该方法大幅度提高了幅值系数的识别精度.      

导航解算中的有色噪声及其协方差矩阵自适应拟合

使用Kalman滤波进行动态导航定位解算需要涉及函数模型和随机模型, 而在实际应用中, 精确的函数模型和随机模型很难直接给出, 因此, 动态Kalman滤波的精度和可靠性将会受到函数模型误差和随机模型误差的影响. 在假设观测噪声和动力学模型噪声主要是具有一阶自相关特性的有色噪声的基础上, 提出了一种基于移动窗口的有色噪声函数模型和随机模型的自适应拟合法. 给出了计算有色噪声估值和噪声协方差矩阵的表达式, 并利用实测数据验证了模型及算法的可行性和实用性. 计算结果表明, 该算法能有效抵制有色噪声对导航滤波结果的影响.      

双星双频地面快速运动目标成像与参数估计

在多输入多输出合成孔径雷达(MIMO-SAR)的基础上,提出使用双卫星、双工作频率实现地面快速运动目标检测、成像和参数估计的方法。利用广义二阶Keystone变换对提取出的运动目标进行距离徙动校正,针对快速运动目标的多普勒模糊问题,使用修正的离散调频傅立叶变换结合最小波形熵搜索完成目标多普勒参数估计后,利用数值搜索的方法对不同工作频率下的速度集合进行交集求解得到目标真实速度值,并给出了一种运算量较小的快速搜索算法。最后,计算机仿真表明了方法的有效性。