具不确定观测和相关噪声的最优递推滤波

应用正交投影定理,对于噪声相关系统,在观测不确定的情况下,求出了状态向量的卡尔曼滤波公式。在线性最小方差准则下,解决了状态噪声一步相关,相同时刻的测量噪声和状态噪声相关,以及测量噪声和状态噪声在相邻时刻均相关的情况下的滤波问题,并给出了递推滤波公式。仿真算例说明了它们的有效性。     

非列紧空间的一般非扩张映象的Ishikawa迭代序列

本文证明了Hilbert空间上的非列紧的一般非扩张映象的Ishikawa迭代序列的收敛性。     

一种快速的飞行器布局方案优选方法

本文引用系统模糊优选理论与基于数理统计正交表的设计法相结合来处理飞行器布局方案优选问题，并举例说明具体用法，文中方法对整个飞行器方案选择有一定参考价值。     

基于EAB资源的交织编译码器的设计与实现

提出了一种新的基于EAB资源交织编译码设计方案，利用FPGA技术实现了数字通信中交织器和解交织器，构建了具体的算法模型，并说明了设计中实际产生的问题及解决方法。     

直扩测控系统抗多址能力分析与验证

为了防止多址干扰造成接收机出现误捕和假锁,改善直接序列扩频测控系统抗多址干扰性能,在Gold码特性和扩频接收机性能分析的基础上,结合最大似然原理,对采用扩频体制测控系统的抗干扰能力进行了分析。为契合工程应用,采用仿真遍历结合理论分析的方式,对Gold码的互相关抑制能力理论值进行了工程修正。在分析捕获阶段的抗干扰捕获门限后,还分析了载噪比估计结果在正常锁定和假锁两种状态下的差异,给出了接收机对假锁状态的判决方法和门限。根据分析和仿真的结果,给出了系统设计约束条件和优化的接收机设计流程,作为测控系统和接收机设计的参考。     

凸轮逆序测量方法

目前各杂志所发表的关于凸轮测量的文章，所讨论的均是凸轮的顺序测量方法，有关凸轮的逆序测量(反求工程)方法，尚未见于文字。本文将对凸轮的逆序测量方法进行探讨。     

算术平均序列的收敛性

下述命题是熟知的:假设 {x_n)_(n=1)~∞是一数列且x_n=a 则1/n x_=a,并且我们知道它的逆命题是不真的。本文给出两个定理和两个推论,定理1断言S_n=1/nx_i 收敛于 a 和 b 的某种组合,这里 a 是(x_n)的子列极限,b 亦如此。在定理2中我们给出1/nx_i=0的一个充要条件,两个推论也是有趣的。     

期望状态序列导向的深空探测器规划修复方法

Aiming at the challenges caused by the persistence, concurrency and energy consumption of probe actions, a plan repair method of deep space probe based on the expected state sequence is proposed. In this method, the expected state sequence is formed of the expected effect of the unfinished action and the expected precondition of the unexecuted action in the pre designed plan, according to the execution status of the action. The expected state sequence is an ordered set of states with mixed logic and energy, providing subgoals for plan repair and also transforming the plan repair problem into the state transition path searching problem. During the search, the plan repair strategy with energy supply priority is proposed, which separates the logic repair from energy repair to reduce the difficulty of solving the problem. And this method enables the probe to recover from plan failure autonomously. Finally, the effectiveness and rationality of the proposed method are verified through simulation by taking the Mars Orbiter as an example.     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

激光辅助车削工艺参数对单晶硅表面质量的影响

为了提高单晶硅激光辅助车削加工表面质量,通过开展激光辅助和常规车削加工试验,结合表面粗糙度、表面形貌及拉曼光谱检测,研究激光辅助车削技术对加工质量的影响。基于正交试验方法,研究单晶硅激光辅助车削工艺参数对表面粗糙度的影响;通过方差分析和极差分析评估各因素对表面粗糙度的影响。研究结果表明：与常规车削相比,激光辅助车削可有效提高加工表面质量,降低材料表面的残余应力。主轴转速、进给速度、切削深度和脉冲占空比对表面粗糙度的贡献率分别为17.51%、44.48%、6.69%和14.70%。确定最佳加工参数组合如下：主轴速度为4 000 r/min,进给速度为2 mm/min,切削深度为5μm,脉冲占空比为30%,最终获得表面粗糙度Rq为2.4 nm的高质量表面。