TC4钛合金静止轴肩和传统搅拌摩擦焊的温度场对比

基于有限元软件ABAQUS对6mm厚的TC4钛合金传统及静止轴肩搅拌摩擦焊温度场进行了有限元模拟.结果表明,对比传统搅拌摩擦焊接,静止轴肩搅拌摩擦焊接具有较小的高温区,前进方向上具有较大的温度梯度,厚度方向上呈现柱状椭球形分布,上、下表面温度峰值差异较小,具有重叠性较好的热循环曲线.     

温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

幂律型流体撞击射流破碎特性直接数值模拟

凝胶推进剂的双股射流撞击雾化广泛应用于液体火箭发动机的燃烧室中,其破碎特征及雾化效果直接影响燃烧效率。为探究雾化特性的发展规律,采用直接数值模拟DNS方法,对射流速度为100m/s的剪切稀化非牛顿液体正交撞击产生的雾化特征、液体表面积、表面波、涡特性以及非牛顿特性开展研究。结果表明,射流下形成的雾化流场迅速扩张形成液膜,液膜两侧边缘破碎成大量的液丝与液滴,核心部分产生撞击波后在气体力的作用下逐步发展为带有凸起和褶皱的不稳定表面波,其撞击波波长最大可达2.46倍射流直径。液体表面积不断增长,但无量纲表面积总体呈现先下降再上升的趋势。气体中的涡量分布则分为有序附着区和无序爆炸区两类,并且涡量主要集中分布于气相区域。此外,射流撞击时产生强剪切使该液体内部的粘性系数下降,最低仅为初始粘性系数的0.3倍。     

发动机唇口电热防冰系统性能仿真

采用三维耦合传热方法对发动机唇口电热防冰系统进行了多状态下的性能仿真,获得了唇口表面平衡温度及动态温升响应时间,以此评估防冰系统性能,并通过与冰风洞试验结果对比,对仿真过程进行了修正。研究表明:唇口表面加热区平衡温度均高于273.15 K,温升响应时间小于60 s,满足防冰需要,较为严酷的防冰状态点主要为飞行速度较大、环境温度较低的状态点;修正唇口材料导热系数后,仿真与试验结果吻合良好。研究结果能有效指导工程研制,对提高防除冰仿真分析结果的准确性提供了很好的借鉴。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

卫星导航定位方程的病态条件

定位精度因子(PDOP)上限取值是导航星座设计及其性能评价的基本依据。本文系统地论述卫星导航定位方程及其精度评定算法以及线性方程病态条件,通过实测和仿真数值试验结果对比分析,详细论证PDOP与卫星导航定位方程病态条件的关系,进而确定PDOP上限取值,以满足实际工程应用需求。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

等离子体助燃下超燃支板燃烧室燃烧特性数值研究

为了将支板喷注器与等离子体射流这两种促进超声速燃烧室燃烧的方式结合起来,设计了一种带有等离子体射流喷孔的支板燃烧室,并在超声速来流的条件下,针对燃料喷注总压、燃料喷注位置、等离子体射流介质、等离子体射流总压对燃烧室燃烧性能的影响进行了三维数值模拟。研究发现:增大燃料的喷注总压,燃烧室的燃烧范围明显增大,燃烧效率呈现出先增大后减小的趋势,在燃料喷注总压为2.0MPa时,燃烧效率达到最大值90.4%;不同的燃料喷注位置对燃烧室的燃烧范围影响较小;等离子体射流介质为O2时,燃烧效率最高,燃烧范围最广;提高等离子体射流的喷注总压,能够提升凹腔剪切层高度,有效促进燃烧,但同时也带来了更高的总压损失。