BMCMC法分析2009年墨西哥H1N1流感病毒与中国流感病毒的进化关系

从GenBank上下载所有1978-2009年在中国分离的H1N1亚型流感病毒的HA和NA基因及所有同期在中国分离的A型流感病毒(宿主包括人、猪和禽)的PB1、PB2、PA、NS、NP和M基因的序列,将这些基因序列与2009年在中国发生的墨西哥H1N1流感病毒的对应基因序列进行BMCMC法分析,绘制BMCMC进化树,结果揭示中国发生的墨西哥H1N1流感病毒的HA和NA基因相对独立于中国季节性H1N1流感病毒;M基因相对独立于中国国内的季节性流感病毒和禽源流感病毒;PB1基因包含在季节性流感病毒的分群内;PB2基因和NS基因与国内重排的流感病毒相关,但相对独立于国内的季节性流感病毒和禽源流感病毒;PA基因包含在国内禽流感病毒的分群内;NP基因则与国内传统的猪流感病毒相关,但相对独立于国内的季节性流感病毒和禽源流感病毒.     

SHS法制备硼化物陶瓷粉体的表征分析

采用自蔓延高温还原合成方法制备TiB2,TiB2-Al2O3和ZrB2-Al2O3陶瓷粉末.利用XRD,XPS,SEM以及TEM等分析测试手段对合成粉末进行表征和分析.结果表明,TiB2,ZrB2和Al2O3分别以主晶相的形式存在于所合成的各自粉体之中.相比之下,TiB2单相陶瓷粉末颗粒分布较宽.由于自蔓延高温合成(SHS)温度很高,部分颗粒形成团聚,宏观上使颗粒的平均粒径变大(＞5μm);而TiB2-Al2O3和ZrB2-Al2O3复合陶瓷粉末,因合成过程中Al2O3的形成,使得颗粒粒度分布明显变窄,分布均匀,颗粒尺寸也相应减小.分析认为这主要与复合粉末合成过程中,不同颗粒间形成良好结合的界面有关.     

高性能的标准单元库设计

从仿真和流片两个方面对标准单元库的验证方法进行了研究.在仿真方面,提出了采用静态时序分析工具和SPICE仿真工具对单元的估算值和仿真结果进行比较分析的方法来验证,同时还给出了具体的操作步骤实例.在流片验证中,提出了一种非常有效的电路结构.这种电路结构不但能够准确验证时序,还能极大地减少PAD数量;最重要的特点是:该电路能够完全避免PAD和非被测单元的引入带来的额外延迟,从而得到准确的被测单元延迟.     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

过失速机动飞机的鲁棒非线性控制律设计

 采用非线性动态逆和结构奇异值综合方法设计了过失速飞行条件下飞控系统控制律,解决了飞控设计中面临的非线性和鲁棒性问题。应用非线性动态逆的目的就是对过失速机动飞行条件下高度非线性的飞机动力学进行线化;从而围绕线性的快逆回路应用结构奇异值综合方法设计相应的鲁棒控制器,以提供对驾驶员指令的鲁棒跟踪。所设计的飞控系统将达到期望的飞行品质,确保系统对过失速机动飞行过程中因非定常气动力效应引起的系统参数摄动鲁棒性良好。高逼真度、非线性的仿真验证了这一点。     

一种具有自适应能力的结构综合方法

 从工程应用的可靠性出发,本文提出一种具有自适应能力的结构综合方法(简称ASSM算法)及保证其实施的一系列技术途径,通过各种典型算例的考核计算,表明ASSM算法具有很高的计算效率及良好的适应能力,即使对于较复杂的算例,也仅需5～6次结构分析即可达到或接近优化设计,显示了自适应方法的优势。     

Combustion Synthesis of h-BN-SiC Ceramic Composites

The feasibility was demonstrated to fabricate h-BN-SiC ceramics through combustion synthesis of the mixture of boron carbide and silicon powders under 100 MPa nitrogen pressure. The mass fraction of BN and SiC in the combustion products were found to be 72 % and 28 % respectively. The thermodynamics of the synthesis reaction and the adiabatic combustion temperature were calculated on the theoretical ground. The bending strengths of the ceramics were measured to be 65.2 MPa at room temperature and 55 MPa at 1350 ℃. The phase composition and microstructure of the combustion products were identified by X-ray diffraction (XRD) and scanning electron microscopy (SEM).     

Effects of the Fabrication Processes of NC-Si:H Films on Their Mechanical Properties

Studies of nanoindentation were performed on nc-Si:H films to evaluate the effects of the fabrication processes on their mechani-cal properties. It is observed that with the decrease of the SiH4 contents, the grain size of the films increases gradually, and as does the crystalline volume fraction. The smaller the grains become, the more homogeneous the films, and the more even the hardness as well as the modulus will be. The hardness and the modulus will increase with the substrate’s temperature rising. The hardness and the modulus of the nc-Si:H films on the Si substrate prove to be higher than those on the glass substrate given the same technology parameters. How-ever, the films on the glass substrate appear to be more homogeneous.     

基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

三元共掺杂对YSZ热障涂层热物理性能的影响

采用NiO、Er_2O_3、Yb_2O_3、Y-2O_3、ZrO_2粉末为原料,用高温固相合成法制备复合陶瓷材料,研究该复合陶瓷材料的比热、热扩散系数、热导率等热物理性能,并与传统8YSZ热障涂层材料进行对比。利用XRD测定所制备的陶瓷样块的晶体结构和物相组成,分析该陶瓷试样的物相组成及高温相稳定性。结果表明:NiO、Er_2O_3、Yb_2O_3共掺YSZ后,室温至1500℃范围内的热扩散系数为0.36～0.56 mm^2/s,与8YSZ相比,降低了约20%;室温至1500℃的热导率为1.45～1.55 W/(m·K),比8YSZ降低了18%;2EYNYSZ陶瓷材料具有单一的相结构,经1500℃热处理100 h之内不发生相变。