海天混杂闪烁背景下运动点目标检测新方法

针对海天混杂闪烁背景及单像素运动点目标的特征,设计了海天相连区域快速定位及基于模式分类的环域全向差分扩展中-均值滤波的预处理算法,二次进行全向差分均值滤波后,利用基于直方图的自适应阈值分割得到初步侯选目标点.形态学滤波保留有效的单像素侯选点,最后进行帧间侯选目标点之间的相关性分析和目标短时丢失的直接再搜索.仿真实验采用两个实拍场景中加入单像素仿真目标生成的220帧图像,结果为:信噪比≥0.5时单帧检测率为91%,3帧以上的连续检测中检测率达到95%;对照组22帧不含仿真点目标,3帧以上的连续检测虚警数为0.      

鲁棒滤波技术在脉冲星导航中的应用

  提出将鲁棒扩展卡尔曼滤波(REKF)用于增强X射线脉冲星导航系统克服星表误差影响的能力。指出星表误差可以看作模型不确定性的一部分,采用鲁棒滤波技术进行处理。对REKF和传统扩展卡尔曼滤波(EKF)的性能进行对比。仿真结果表明,存在星表误差的情况下,采用REKF算法进行航天器导航,能够获得优于EKF的定位精度。     

模型预测控制在永磁同步电机系统中的应用发展综述

随着数字技术的发展,模型预测控制(MPC)已经广泛应用于交流传动系统。首先介绍了经典MPC策略——有限控制集MPC和连续控制集MPC的原理。其次综述了多步预测控制、多矢量预测控制、具有参数鲁棒性的预测控制、广义模型预测、显式模型预测这些常见的改进MPC的研究现状,并提出相关研究思路。最后,根据MPC的应用需求和研究现状,展望了未来需要进一步深入和拓展的研究方向。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

基于双变量预测控制的表贴式永磁同步电机直接转矩控制系统

基于电压矢量幅值和相角为变量的表贴式永磁同步电机(SPMSM)定子磁链幅值和转矩表达式,给出了9个不同幅值和相角的备选电压矢量,采用预测控制计算得出施加不同电压矢量下一时刻的定子磁链幅值和转矩值,建立了基于磁链和转矩误差的目标函数,并选择使目标函数最小的电压矢量为作为下一时刻施加的最优电压矢量。仿真结果表明:在双变量预测控制下,SPMSM直接转矩控制系统运行良好,定子磁链轨迹为理想圆,磁链和转矩均符合控制要求,转速跟踪良好,定子电流波形正弦。进一步对比分析表明:与开关表和固定电压矢量选择策略相比,双变量预测控制能显著减小转矩和磁链脉动。与开关表相比,转矩脉动均方根误差降低了62.92%,磁链脉动均方根误差降低了45.05%,评价函数均值降低了60.30%;与固定电压矢量选择策略相比,转矩脉动均方根误差降低了22.40%,磁链脉动均方根误差降低了3.85%,评价函数均值降低了15.93%。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

叶片磨抛机器人力/位混合控制的设计与实现

为提高航空类发动机叶片的自动化磨抛精度,减小复杂曲面叶片加工轨迹控制误差,采用基于六维力传感器的机器人力/位混合控制策略,实现机器人磨抛轨迹的在线修正。搭建以Staubli机器人和ATI六维力传感器为核心部件的叶片磨抛验证平台,通过C++开发上位机,采集磨抛过程中六维力传感器信息并进行Kalman滤波。通过示教确定机器人运动轨迹,对机器人运动轨迹与力传感器信息进行采集分析,确定基于力/位混合控制可以实现机器人运动轨迹的在线修正,为复杂曲面的叶片磨抛轨迹控制提供一种解决方案。     

采用序列概率比方法检测航空发动机传感器软故障

提出基于卡尔曼滤波和序列概率比方法进行某型涡扇发动机控制系统传感器软故障检测新方法.研究了采用修正的序列概率比方法处理滤波残差,检测传感器软故障;并将该方法与残差加权二乘算法WSSR(Weighted Sum of Squared Residual)检测传感器软故障过程进行了对比.仿真结果表明,序列概率比方法较WSSR法所需决策时间短,适合于航空发动机传感器软故障检测.      

基于多相结构的直接中频采样接收机设计及实现

直接中频采样的设计通常采用类似模拟接收机的结构,而基于多相结构的数字正交变换无需正交本振,结构上更适用于实时处理系统。本文对基于多相结构的数字正交变换原理进行了分析,并根据多抽样率信号处理理论,提出了一种内插时延滤波器、半带抽取滤波器实现方法。试验结果表明,使用该方法设计的系统切实可行。     

声矢量传感器阵中基于Kalman滤波和OPASTd的DOA跟踪算法

研究了声矢量传感器阵动目标角度跟踪问题,并提出了声矢量传感器阵中 一种基于Kalman滤波和正交压缩近似投影子空间跟踪(Orthonormal projection approximation and subspace tracking of deflation, OPASTd)的波达方向(Direction of arrival,DOA)跟踪算法。该算法通过OPASTd算法来进行DOA的跟踪,从而克服了PASTd算法由于在某些情况下振荡但不收敛进而压缩数据、在迭代更新中由特征向量的不准确性产生误差累积等原因引起破坏信号子空间正交性的缺陷。Kalman滤波和OPASTd相结合算法可在估计角度的同时进行数据关联,与传统的PASTd算法相比,角度跟踪性能更好。该算法的优越性均可在文中得到验证。