Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

Temperature Fluctuations,H II Region Abundances,and Primordial Helium

There is evidence for temperature fluctuations in Planetary Nebulae and in some Galactic H II regions. If such fluctuations occur in the low metallicity, extragalactic H II regions used to probe the primordial helium abundance, the derived 4He mass fraction, YP, could be systematically different from the true primordial value. Although this effect could be large, there are no data which allow us to estimate the size of the temperature fluctuations for the extragalactic H II regions. Therefore, we have explored this effect via Monte Carlo simulations of the data in which the abundances derived from a fiducial data set are modified by T chosen from a distribution with 0 T Tmax where Tmax is varied from 500 K to 4000 K.     

非线性反馈线性化方法在飞控系统中的应用

应用非线性反馈精确线性化方法进行了飞机自动着陆系统设计。首先,用非线性微分方程组表示的飞机纵向控制系统,在经过输入输出反馈线性化以后,可等效为线性系数;然后,用线性的ＰＩＤ控制方法对变换后的线性系统进行了设计;最后,考虑风的干扰,对所设计的飞机自动着陆控制系统进行了数字仿真。仿真结果表明,用反馈线性化方法设计的飞控系统具有良好的性能。     

非线性主轴降维映射法在固体火箭发动机设计优化中的应用

为在二维或三维空间中表达固体火箭发动机高维设计空间,引入非线性主轴降维映射法对多维非线性设计优化问题进行降维处理。以某大型固体火箭发动机设计问题为例,将10变量4有效约束优化问题降维映射到二维空间进行研究,拟合的非线性主轴降维映射模型中,目标函数和约束函数的相对误差控制在1.5%以内。研究表明,非线性主轴降维映射法具有发现多变量非线性优化数学模型本征特性的特点,能对设计变量重要性排序;通过降维展示设计空间全景,为优化算法和优化初始点优选提供了直观、有力的工具;优化轨迹实时展示为优化算法性质研究及算法切换提供了依据;根据优化轨迹从优化结果在降维空间中的位置能够判断优化结果是否具有全局最优解特性。     

Effects of the Fabrication Processes of NC-Si:H Films on Their Mechanical Properties

Studies of nanoindentation were performed on nc-Si:H films to evaluate the effects of the fabrication processes on their mechani-cal properties. It is observed that with the decrease of the SiH4 contents, the grain size of the films increases gradually, and as does the crystalline volume fraction. The smaller the grains become, the more homogeneous the films, and the more even the hardness as well as the modulus will be. The hardness and the modulus will increase with the substrate’s temperature rising. The hardness and the modulus of the nc-Si:H films on the Si substrate prove to be higher than those on the glass substrate given the same technology parameters. How-ever, the films on the glass substrate appear to be more homogeneous.     

液体火箭发动机涡轮泵非线性转子系统稳定性影响因素研究

针对低温液体火箭发动机涡轮泵转子非线性系统开展了动力稳定性研究。采用有限元法建立了涡轮泵转子系统的动力学模型,研究了安装偏心对转子密封系统稳定性的影响,给出了失稳转速随安装偏心的变化规律。研究了存在安装偏心时当量密封间隙、轴承支承总刚度及轴向位置对液体火箭发动机涡轮泵转子系统稳定性的影响,分析了失稳转速随当量密封间隙、轴承支承总刚度及轴向位置的变化规律。最后开展了冷吹试验和热试验研究,验证了本文的理论研究结果。本文的研究为液体火箭发动机涡轮泵转子系统结构设计、故障诊断与安装维护提供理论依据。      

非线性方程求解中的幂指函数法

给出幂指函数在非线性方程求解中的一种迭代算法,既给出初始值的判断条件,又给出方程根附近的近似误差公式。算例表明:与其它五种方法相比,本文提出的幂指函数法精度较高,其收敛速度是Newton法和二次曲线法的10倍左右;而计算时间是Newton法和二次曲线法的十分之一左右。     

H_∞滤波算法及其在GPS/SINS组合导航系统中的应用

 在对 H∞ 估计问题进行数学描述的基础上,建立了一种 H∞ 次优滤波算法的迭代方程。定性讨论了H∞滤波算法与传统 Kalman滤波器的关系,通过在 GPS/SINS组合系统中的实际应用进一步从精度、鲁棒性等性能指标方面对 H∞ 滤波和 Kalman滤波算法进行了比较。仿真结果表明,在理想条件下,Kalman滤波方法具有较高的精度;但是,当系统模型和外部干扰统计特性发生变化时,H∞ 滤波算法明显具有良好的鲁棒性能,同时,估计精度也较高,有效地克服了 Kalman滤波器存在的局限性。     

涡扇发动机加速过程的模糊控制

采用一种连续型比例积分公式的模糊控制器控制涡扇发动机加速过程，为了使控制满足加速过程最大转速，高压涡轮进口最大温度，压气机最低允许喘振裕度等约束条件并改善加速性能，利用遗传算法对模糊控制器中的3个量化因子进行了优化，优化后的模糊控制器完全可以加速过程要求，具有较好的动态性能，适当划分飞行包线后还可扩展到整个飞行包线。     

HTPB复合固体推进剂含损伤和老化本构研究

通过热氧老化实验、声发射损伤检测实验和蠕变柔量测试实验确定HTPB复合固体推进剂非线性本构关系，并与Schapery非线性本构方程进行比较，结果表明，含损伤老化模型较好地解释了HTPB复合固体推进剂的非线性特征，可以应用分析HTPB复合固体推进剂的力学特性。