C 波段全场效应晶体管化宽带微波接收机

介绍一个全场效应晶体管化 C 波段卫星转发器用微波接收机的方案,并给出微波通道部分的实验结果,其中采用元器件均以国内1986年生产,现空间仍在用的高可靠性器件为设计依据和实验样管。实验结果与法国汤姆逊公司1986年为我国研制生产的 C 波段接收机(以下简称法国接收机)相比,电气指标均能达到该公司产品水平,同时具有结构简单、体积小、低功耗等优点。该方案同样适于 Ku波段应用。     

一种数字化DS/BPSK扩频接收机

介绍一种新型数字化DS/BPSK(Direct Spread/Binary Phase Shife Keying)扩频接收机的设计.该接收机采用专用数字相关器为核心的硬件设计,并结合数字处理算法完成扩频信号的解调.技术上采用串并组合的伪码捕获、科斯特环载波跟踪、延迟锁定环伪码跟踪等方式,可通过软件算法灵活实现.该接收机具有综合性能强,及软件接口灵活的特点,可有效地应用于基于码分多址的多目标测控系统中.     

用于识别双星故障的RAIM算法

由于传统的基于识别门限的卫星故障识别算法存在漏检和误警致使识别率较低,为此提出一种可用于识别双星故障的接收机自主完好性监测算法.该算法通过构造新的奇偶矢量与故障特征平面,利用奇偶矢量与故障特征平面之间的几何关系来识别卫星故障,使得算法不再受限于识别门限的影响,从而有效地避免了由于识别门限引起的识别效率较低的问题.计算机仿真结果表明:改进后的算法与传统的基于识别门限的算法相比,双星故障正确识别的性能有显著的提高,正确识别率可达到90%.同时,与基于门限识别的重构最优奇偶矢量法相比,计算量可减少约61.2%以上.     

Civil unmanned aircraft system operation in national airspace: A survey from Air Navigation Service Provider perspective

Unmanned Aircraft Systems (UASs) have advanced technologically and surged exponentially over recent years. Currently, due to safety concerns, most civil operations of UAS are conducted in low-level uncontrolled area or in segregated controlled airspace. As the industry progresses, both operational and technological capabilities have matured to the point where UASs are expected to gain greater freedom of access to both controlled and uncontrolled airspace. Extensive technical and regulatory surveys have been conducted to enable the expanded operations. However, most surveys are derived from the perspective of UAS own operating mechanism and barely consider interactions of their non-segregated activities with the Air Traffic Management (ATM) system. Hence, to fill the gap, this paper presents a survey conducted from the perspective of Air Navigation Service Provider (ANSP), which serves to accommodate these new entrants to the overall national airspace while continuing flight safety and efficiency. The primary objectives of this paper are to: (A) describe what typical ANSP-supplied UAS Traffic Management (UTM) architecture is required to facilitate all types of civil UAS operations; (B) identify three major ANSP considerations on how UAS can be accommodated safely in civil airspace; (C) outline future directions and challenges related with UAS operations for the ANSP.     

射流管伺服阀前置级压力特性

为分析射流管伺服阀射流管喷嘴高压射流区的特性,建立了射流管伺服阀前置级数学模型,得到了射流管偏移值、射流管喷嘴半径和接收孔半径对接收器压力分布、喷嘴出口流速及接收器的左右孔恢复压力的影响规律.流场分析发现射流管喷嘴的高速射流出口处容易产生旋涡,且存在环状负压效应.结果表明:高压射流状态下,射流管喷嘴半径增大,恢复压力增加;接收孔半径增大,恢复压力降低.接收孔半径与射流管喷嘴半径之比的最佳取值区间为[1.3,1.5].当射流管偏移值增大时,在偏移值增大一侧,射流管与接收孔之间的有效流体接收面积增大,射流管与接收孔之间的流体旋涡扩大,内部流场环状负压效应增加,接收孔恢复压力降低.      

地基伪卫星系统多址测距误差的校正算法

相对于卫星导航,地基伪卫星与接收机距离较近,测距中不涉及电离层传播等误差,易实现高精度测距和定位。但由于地基伪卫星位置固定,在信号连续发射模式下伪卫星信号间的多址干扰(MAI)会引起相对恒定的测距误差,针对地基伪卫星系统这一特点,提出一种基于反馈串行干扰抵消(SIC)的测距算法。首先对全部伪卫星信号进行捕获跟踪和功率估计,然后通过串行干扰抵消算法降低强功率伪卫星信号对期望测距信号的干扰,通过反馈模式进一步提高干扰抵消算法的性能。仿真结果表明,该方法可有效改善地基伪卫星系统强远近效应区域内的测距性能,不考虑其他误差下在强远近效应区域内基于码环可将伪卫星测距性能从10 m以上降低到约0.3 m。     

Attitude determination of planetary exploration rovers using solar panels characteristics and accelerometer

In this study, we propose a new attitude determination system, which we call Irradiance-based Attitude Determination (IRAD). IRAD employs the characteristics and geometry of solar panels. First, the sun vector is estimated using data from solar panels including current, voltage, temperature, and the normal vectors of each solar panel. Because these values are obtained using internal sensors, it is easy for rovers to provide redundancy for IRAD. The normal vectors are used to apply to various shapes of rovers. Second, using the gravity vector obtained from an accelerometer, the attitude of a rover is estimated using a three-axis attitude determination method. The effectiveness of IRAD is verified through numerical simulations and experiments that show IRAD can estimate all the attitude angles (roll, pitch, and yaw) within a few degrees of accuracy, which is adequate for planetary explorations.     

采用阵列天线的GPS接收机的多径抑制方法

提出一种新的用于阵列天线GPS接收机的多径抑制方法。考虑到通常GPS视线信号的来波方向与多径的来波方向不同,在每个导航数据符号位内测距（C/A）码重复,通过对阵列接收的信号矢量与它本身的延迟信号矢量互相关,提高接收机前端信噪比,再利用最大特征值法和前后向空间平滑技术准确地估计期望卫星视线信号（LOSS）的来波方向。最后综合多个GSC子阵列有效地降低了相关多径对码跟踪精度的影响。仿真结果显示,该方法能使接收机在与LOSS码同步前准确估计LOSS的角度信息,有效抑制相关多径,且鉴相结果准确。     

星间链路发射机时延零值的数字标定算法

The traditional absolute calibration based on oscilloscopic observation is not suitable for crosslink transmitter. A new calibration algorithm is developed by using a digital signal processing technique. The output signal of crosslink transmitter and the pulse per second signal are sampled in synchronization. At first, the delay reference is determined according to straight line fitting for the signal level stepping segment. The sampling data of crosslink transmitting signal is decimated and then phase acquisition processing is made to determine the initial synchronization point. A fine search for the start of the pseudo random code has been processed between front and rear of the initial synchronization point. Finally, the transmitter delay can be obtained according to the sampling frequency and the calibration delay of the test cable and attenuator. Compared with the oscilloscopic observation method, the analysis and test results show that the proposed technique has overcome the faults caused by whole chip ambiguity and the calibration accuracy can be improved by an order of magnitude.     

The impact of orbital errors on the estimation of satellite clock errors and PPP

Precise satellite orbit and clocks are essential for providing high accuracy real-time PPP (Precise Point Positioning) service. However, by treating the predicted orbits as fixed, the orbital errors may be partially assimilated by the estimated satellite clock and hence impact the positioning solutions. This paper presents the impact analysis of errors in radial and tangential orbital components on the estimation of satellite clocks and PPP through theoretical study and experimental evaluation. The relationship between the compensation of the orbital errors by the satellite clocks and the satellite-station geometry is discussed in details. Based on the satellite clocks estimated with regional station networks of different sizes (∼100, ∼300, ∼500 and ∼700 km in radius), results indicated that the orbital errors compensated by the satellite clock estimates reduce as the size of the network increases. An interesting regional PPP mode based on the broadcast ephemeris and the corresponding estimated satellite clocks is proposed and evaluated through the numerical study. The impact of orbital errors in the broadcast ephemeris has shown to be negligible for PPP users in a regional network of a radius of ∼300 km, with positioning RMS of about 1.4, 1.4 and 3.7 cm for east, north and up component in the post-mission kinematic mode, comparable with 1.3, 1.3 and 3.6 cm using the precise orbits and the corresponding estimated clocks. Compared with the DGPS and RTK positioning, only the estimated satellite clocks are needed to be disseminated to PPP users for this approach. It can significantly alleviate the communication burdens and therefore can be beneficial to the real time applications.