基于过渡工作过程的航空发动机气路分析方法

为对发动机机动性能的退化程度进行估计,开展了基于过渡工作过程的气路分析研究。针对气路传感器数目较少的情况,采用序列工作点方法对大量的健康参数进行分析,在增加可用信息量的同时,降低了由多工作点方法的平均效应引入的参数估计系统误差。为解决发动机大偏差性能退化健康参数估计中的计算收敛性问题,提出了间接递归牛顿-拉夫逊法强化非支配分类差分进化算法。针对某型双轴分排涡扇发动机的气路分析结果表明：采用本文所提出的方法能够在气路传感器数目有限的条件下,利用发动机过渡态数据实现对大偏差范围内大量健康参数的高效、准确估计。     

共形光学系统设计研究

共形光学整流罩在保证了光学指标的前提下,与后端的其他结构外形轮廓平滑连接,从而提高了飞行器空气动力学的性能,在航空航天领域具有重要的应用价值。然而,采用特殊面型的整流罩给共形光学系统的像差校正以及加工、检测方面带来了极大的挑战。本文首先分析了共形整流罩像差特性,并在此基础上介绍了两种典型的光学设计。     

小不对称物体配平性能风洞实验研究

用阶跃响应法,在风洞中测量小不对称物体配平性能的实验原理、实验装置、数据处理及部分实验结果。 模型支承于空气静压轴承。在模型内部设有电磁机构,在一次吹风中,可以阶跃方式多次提供不对称量。由高精度、非接触的感应同步器数字测量模型俯仰角变化历程。用修正Newton-Raphson法处理数据,求出小不对称量引起的配平角δ_o、俯仰力矩C_mo和气动刚度C_ma、气动阻尼C_mq等参数。 对11°斜切锥,钝度比分别为0.06及0.16的模型进行了风洞实验。实验M数为33.5和4。实验结果表明,所采用的实验原理、设备及方法可提供较好的精度及分辨率。实验还求出了配平性能(δ_o,C_mo)以及C_ma,C_mq随M数的变化。     

俯仰三角翼的流态及结构

本文对俯仰三角翼的流动特性进行了实验研究，给出了俯三角翼的截面流态特点，对三角翼俯仰 运动的流动机理进行了分析。     

微流星体高速撞击航天器Whipple防护结构损伤特性研究(英文)

采用金刚石模拟高脆性、高熔点微流星体材料,对航天器典型Whipple防护结构进行高速撞击试验.试验表明,撞击产生的高温高压效应导致金刚石部分或全部转化为石墨,金刚石对防护结构的损伤主要体现在中低速阶段,当撞击速度大于4.3km/s时,对后板的灼烧损伤极为显著。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

Vision-based bio-inspired guidance law for small aerial vehicle

During predation, a flying insect can form a stealth flight path. This behavior is called motion camouflage. Based on the study results of this behavior, the perception and neurology of flying insects, a novel bio-inspired guidance law is proposed for the terminal guidance for small aerial vehicle with charge-coupled device imaging seekers. The kinematics relationship between a small aerial vehicle and target is analyzed, and a two-dimensional guidance law model is established by using artificial neural networks. To compare with the proportional guidance law, the numerical simulations are carried out in the vertical plane and in the horizontal plane respectively. The simulation results show that the ballistic of the small aerial vehicle is straighter and the normal acceleration is smaller by using the bio-inspired guidance law than by using the proportional guidance law. That is to say, the bio-inspired guidance law just uses the information of the target from the imaging seeker,but the performance of it can be better than that of the proportional guidance law.     

典型再入返回器气动特性对比与改进研究

返回器气动特性研究对宇宙飞船的研制起着先导和制约作用。文章对Apollo、CEV和类Soyuz这3种典型的轴对称钝头体再入返回器气动布局进行了气动特性的对比分析,发现与Apollo、CEV相比,类Soyuz外形的升阻比偏小,无法满足以第二宇宙速度载人空间再入返回的要求。在此基础上研究了几何参数（包括倒锥角和球冠半径）变化对类Soyuz外形返回器气动性能的影响规律,从中得到类Soyuz外形的改进方向,提出了一种以类Soyuz外形为基础的改进设计外形,并对该外形的升阻特性、稳定性和配平特性等相关气动特性进行了分析。研究表明通过对几何外形参数的调整优化来提高类Soyuz外形的升阻比,从而达到以第二宇宙速度再入返回的升阻比要求,这样的技术途径是可行的。     

220GHz返波振荡器高频特性及互作用研究

文章对220GHz折叠波导慢波电路的返波传输特性进行了研究。介绍了返波振荡器的工作原理,结合模拟仿真和理论分析,针对220GHz的返波振荡器,研究各个参数对冷特性的影响。对220GHz返波振荡器的高频结构进行了初步设计,给出了结构参数以及相应的模拟结果。结果表明在不考虑损耗的情况下,设计的结构可以在中心频率220GHz处获得约为0．5W的功率,可调谐范围是30GHz,调谐电压范围为5．5kV-12kV。     

一种大面积比喷管的分段式设计与数值分析

为了满足大推力上面级发动机大面积比喷管的设计需求,采用了排放冷却前段和单壁辐射冷却尾段的分段式设计方案。在排放冷却前段传热计算的基础上,通过对内流场进行数值模拟,重点研究了单壁尾段在引入上游排放冷却气氢情况下的冷却特性和喷管效率。结果表明:对于大面积比喷管,采用带二次流的单壁金属喷管延伸段是现实可行的,有望达到较好的冷却保护效果并提高喷管效率。