准双曲面齿轮冷摆辗方案回弹误差补偿

提出一种冷摆辗方案,该方案简化了模具结构,采用局部线接触连续塑性成形.采用位移修正算法构建回弹误差补偿迭代系统,对冷摆辗模具进行修正来降低回弹误差.该系统的特点是首先用修正算法预估下一次冷摆辗假设无回弹时工件的几何形状,然后由冷摆辗模具设计原理推出所需要的新冷摆辗模具.基于弹塑性有限元法基本理论,借助有限元数值模拟技术进行实例验证,分析结果证明:该回弹误差补偿迭代系统只需3次迭代工件误差已经在允许的范围内,因此其可大大的缩短生产周期和成本.      

吸气式高超声速飞行器内外流同时测力试验

为研究吸气式高超声速飞行器新型测力试验技术的可行性,在马赫数Ma=6、高度H=27km模拟飞行环境下开展了风洞试验。以轴对称吸气式高超声速飞行器无舵翼简化构型为研究对象,通过合理的试验系统设计解决内外流解耦关键技术,采用两个环式六分量天平在同一车次上测量模型内外流气动力载荷。试验结果表明:内外流气动力天平测量数据和全模气动力数据准确反映了内外流解耦、内外流窜流、进气道起动/不起动以及溢流影响等物理现象;从物理上实现了内外流解耦;内流气动力对全机气动性能贡献大;内外流解耦、进气道起动时,气动力数据准确、重复性好;窜流产生的传力属于内力。试验证明,同时测力试验技术可行,为解决内外流气动数据源于不同试验所致的不确定性问题提供了有效手段。     

太阳能飞机翼肋结构拓扑优化设计

太阳能飞机翼肋结构轻薄且数量众多,其结构形式的合理性对于结构减重、机翼刚度设计等具有重要意义。基于现有太阳能飞机翼肋的结构形式,提出一种翼肋拓扑优化设计方法:首先,应用双向渐进结构优化法(BESO),以单元应力为判断指标,对太阳能飞机典型翼肋进行结构拓扑优化;其次,基于拓扑优化结果对翼肋进行结构细节设计;最后,通过有限元计算,验证翼肋的结构强度、刚度和静稳定性。通过本文方法,能够得到太阳能飞机翼肋更为合理的结构布局。     

民用飞机静气动弹性载荷计算方法研究

以某大型客机为例,根据气动外形利用有限元软件PANTRAN建立高阶气动面元,利用ZONAIR静气动弹性方法,分析了其弹性载荷,包含气动力系数、过载、迎角,并与刚性载荷进行了对比。此方法合理可靠,可用于民用飞机的弹性载荷设计分析。     

高超声速飞行器进气道压缩面逆向设计方法

针对高超声速飞行器进气道压缩面问题,首先研究了激波理论的逆向算法,以此为基础提出了进气道的等强度和等熵压缩面的逆向设计方法,并采用此方法设计了以进气道出口气流参数为设计参数的高超声速飞行器进气道压缩面,然后对两种压缩面进行了性能分析和数值仿真.结果表明:通过逆向设计方法设计进气道压缩面是可行的,其相对于传统方法耗时大大减少;理论计算表明相同设计条件下两压缩面几何参数基本一致,而来流参数也基本不变,设计点下等熵压缩面总压恢复系数高出等强度压缩面6.3%.数值仿真验证了该方法的可行性并研究了非设计状态下两种压缩面的各项性能参数,同时对比了不同马赫数下进气道内部波系分布和气流均匀性.      

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Practical compensation for nonlinear dynamic thrust measurement system

The real dynamic thrust measurement system usually tends to be nonlinear due to the complex characteristics of the rig, pipes connection, etc. For a real dynamic measuring system,the nonlinearity must be eliminated by some adequate methods. In this paper, a nonlinear model of dynamic thrust measurement system is established by using radial basis function neural network(RBF-NN), where a novel multi-step force generator is designed to stimulate the nonlinearity of the system, and a practical compensation method for the measurement system using left inverse model is proposed. Left inverse model can be considered as a perfect dynamic compensation of the dynamic thrust measurement system, and in practice, it can be approximated by RBF-NN based on least mean square(LMS) algorithms. Different weights are set for producing the multi-step force, which is the ideal input signal of the nonlinear dynamic thrust measurement system. The validity of the compensation method depends on the engine’s performance and the tolerance error0.5%, which is commonly demanded in engineering. Results from simulations and experiments show that the practical compensation using left inverse model based on RBF-NN in dynamic thrust measuring system can yield high tracking accuracy than the conventional methods.     

大型枢纽机场中转水平评估研究

为了有效评估我国枢纽机场的中转水平,全面掌握枢纽机场发展中所面临的问题,构建了大型枢纽中转水平评估模型,并以中美欧三个国家和地区典型的大型枢纽为例进行实证分析。研究表明,与美国和欧洲大型枢纽的中转水平相比,我国大型枢纽的中转水平仍有很大差距;我国国内中转航班的中转水平远远低于美国,国内国际互转航班的中转水平与美国相当,国际转国际航班的中转水平高于美国;与欧洲三大国际枢纽的中转水平相比,我国北京首都机场与国际相关的水平中转仍有所不足。     

采用排间界面静压约束伴随方法的多级压气机叶片优化

为解决伴随优化应用在多级压气机中出现的优化工况点漂移问题,在前期薄层N-S方程伴随方法基础上,对目标函数——出口熵增不仅施以质量流量、总压比约束,还添加排间界面静压展向分布作为新的约束条件.以某5级压气机为对象,对其中第1级转、静叶分别在首1.5级和全5级压气机环境下进行了优化.结果表明,施加排间界面静压展向分布约束能够显著解决优化工作点漂移问题,优化后5级压气机的效率提高0.4个百分点.      

综合时序信息的试验优化设计及稀疏求解

考虑不同试验点的试验成本及试验时序信息,在性能指标与影响因素间的响应模型未知情况下,利用装备系统的先验信息构造模型驱动的基函数,构造相应的回归模型来刻画系统的内在关系,分析不同试验点成本及试验时序对试验方案的影响。定义了一种考虑空间权重及批序贯时序的非均匀最优设计模型,将稀疏理论引入到回归试验设计中,把不同批次试验下的回归试验设计模型参数估计问题转换为结构化稀疏重构问题,讨论了非均匀最优设计的构造定理,提出结构化稀疏参数求解算法。算例表明:利用本方法生成的试验点考虑了试验点空间权重和试验时序信息,更符合实际试验规程;采用本方法获得的响应函数得到的期望预测误差更小。