CuAl2／Al复合材料的固相反应合成技术及与Al液的接触反应研究

研究了Ａｌ，Ｃｕ在真空状态下的纯固相接触反应情况，试验表明，Ａｌ粉、Ｃｕ粉在６００℃，保温６ｈ时，两者以完全发生反生成ＣｕＡｌ２（θ相），生成的θ相沿铝基体组织晶界分布并在结晶过程中具有择优取向特性，形成仅含沿晶界方向的主干与垂直于晶界的二次晶轴的树枝晶形貌。     

低温度系数标准电阻器的研制

主要介绍了低温度系数标准电阻器的研制,包括采用的电阻合金材料、电阻合金材料的筛选、匹配与加工制作,低温度系数标准电阻器的技术参数、温度系数测量方法,减小温度系数采用的补偿方法,测试结果分析。     

推力矢量和二元喷管

推力矢量是第四代战斗机获得过失速机动性的必要条件,而二元喷管又是推力矢量控制中性能较为优越的一类喷管。本文较全面地阐述了目前世界上推力矢量和二元喷管的发展和现况、二元喷管的构造和性能、二元喷管对改进飞机升阻特性和机动的作用。推力矢量能显著提高飞机在空战中的作战效率以及推力矢量控制所需的效能也在文中作了介绍。     

燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

利用双目标优化寻求颤振抑制控制律

本文对一个三角机翼/外挂系统的颤振主动抑制进行了系统的研究。在理论上,对如何应用现代控制理论设计优化控制律进行了探讨;对非定常气动力拟合的Pade矩阵近似作了改进;提出了用理想极点和二次型性能指标进行双目标优化来确定加权矩阵的思想;在实现上,用状态观测器和单秩法极点配置两种方法设计了输出反馈控制律。风洞实验结果表明:用本文的方法所综合的控制律是合适有效的,成功地使机翼/外挂系统的颤振速度提高了15.7％,与理论计算结果吻合良好。     

Image restoration of the asymmetric point spread function of a high-resolution remote sensing satellite with time-delayed integration

The calibration and validation team of the Korea Aerospace Research Institute has calibrated and validated the image data of the KOMPSAT-2 since the launch of KOMPSAT-2 on July 28, 2006. The asymmetric phenomenon of the point spread function of the KOMPSAT-2 image data is evident in both the along and the across direction, most likely because KOMPSAT-2 has a 1 m ground sample distance high-resolution camera with time-delayed integration. Furthermore, because KOMPSAT-2 is in space, the KOMPSAT-2 image data has been corrected with good results by means of modulation transfer function compensation.     

基于网络的GPS时钟信号发布系统

从空管的实际应用出发,本次研究尝试以TCP Server/Client的模式进行GPS时钟信号的网络发布,通过这种方式实现多套系统灵活的时钟信号引接。     

基于B/S的空管自动化综合航迹显示系统的设计与实现

提出一种基于B/S的综合航迹显示系统,该系统通过解析空管自动化系统的综合航迹实现了在IE浏览器上对区域内的航迹的监视。系统实现主要包括三部分:一是综合航迹的接收,主要通过对同步串口卡的数据读取;二是对数据的数据库处理;三是对综合航迹的显示。系统实现了对MH4008003类数据的解析以及对空管自动化系统的地图解析,并且在IE界面上提供了航迹态势显示以及用户交互接口。     

Bursts in the HETE-2 catalogue

We have studied a set of GRBs detected by HETE-2 satellite with special focus on low-energy part of the spectrum. Results of data reduction procedures of different members of the HETE collaboration were combined with other publicly available information creating a concise catalogue. A more detailed analysis of lightcurves of the prompt emission was performed using data from FREGATE instrument.     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.