Ultrasound assisted solidification process of ternary Cu–Sn–Sb alloy

It is well-known that the application of ultrasound during liquid to solid transitions for alloys can refine the solidification microstructure and thus improves the mechanical properties. How-ever, most published work focuses on single phase dendritic growth, whereas little has been con-ducted on the multiphase alloys with complicated phase transformations during solidification. In this work, the solidification process of ternary Cu40Sn45Sb15 alloy was realized within intensive ultra-sonic field with a resonant frequency of 20 kHz and ultrasound power from 0 W to 1000 W. The ultrasound refines the size of the primary e(Cu3Sn) intermetallic compound by two orders of mag-nitudes. If the ultrasound power increases to 1000 W, g(Cu6Sn5) phase nucleates and grows directly from parent liquid phase without the occurrence of peri-eutectic reaction on the top of the alloy sam-ple where the ultrasound intensity is sufficiently high. These microstructural variations lead to the enhancement of compressive strength and elasticity modulus of ternary Cu40Sn45Sb15 alloy.     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

复合材料格栅结构研究进展与应用

介绍了格栅复合材料的结构特征及其制备工艺。同时,对复合材料格栅结构分析设计、性能测试和该结构在航空、航天工程中的应用现状进行了概述。     

陶瓷隔热瓦的缺陷修补

分别采用了MgO、YSZ和Al₂O₃三种陶瓷粉体和一种含隔热瓦本体成分的粉料对陶瓷隔热瓦缺陷进行修补。研究了修补前后材料的微观形貌、力学及隔热性能。结果表明：采用含隔热瓦本体组成的粉料对陶瓷隔热瓦进行修补,修补部位与本体部位相容性好,且微观形貌相似,仍保持纤维搭接的多孔空间网络结构;修补后试样密度0.24 g/cm³、室温热导率0.044 W/（m·K）、压缩强度0.58 MPa;1 200℃、30 min热处理后,修补部位与本体部位结合性好,未出现裂纹、凹陷等缺陷,是有效的缺陷修补方法。     

分层结构的雷达告警设备软件测试方法

雷达告警设备是现代作战飞机不可或缺的雷达对抗设备,主要用于对敌方雷达威胁信号的告警.分析了分层结构的雷达告警设备软件的特点,借鉴集成测试中自底向上增量式集成策略,提出了一种综合运用调试、插桩和仿真的配置项测试方法.测试结果表明,方法对此类以数据处理功能为核心、分层结构设计的嵌入式软件测试,有很好的借鉴作用.     

飞机服役环境当量加速腐蚀折算方法研究

文中依据飞机服役机场地面环境谱与腐蚀损伤等当量原则,建立了环境加速腐蚀当量折算关系,给出了飞机结构主要高强度铝合金材料的当量折算系数α及HR-α、T-α曲线。依据建立的当量折算关系编制的加速环境谱,对飞机铝合金构件进行加速腐蚀试验研究,得到了温度(T)、相对湿度(RH)对环境当量折算系数的影响规律,为飞机结构防腐控制及日历寿命研究提供了工程技术依据。     

温度边界层对壁湍流多尺度相干结构的影响

用热线风速仪以高于对应最小湍流时间尺度的分辨率精细测量了风洞中壁面加热平板湍流边界层不同法向位置流向速度分量的时间序列信号, 与常温情况相比, 热对流加速了壁湍流中流体的动量、质量和能量的交换, 加快了湍流边界层的发展;用子波分析方法研究了壁面加热对壁湍流多尺度相干结构喷射和扫掠条件相位平均波形的影响, 显示热对流明显增大了缓冲层相干结构扫掠过程和喷射过程的强度, 是增强壁湍流中流体的动量、质量和能量交换的根本原因.      

多压电膜式零质量射流激励器的设计与性能研究

设计了一种多压电膜式零质量射流激励器,并利用热线风速仪,得到了对应于射流中心线上固定位置处速度最大时的最佳频率.在该频率下,测量了零质量射流在不同孔径时沿中心线的速度分布;测量、分析和比较了不同激励膜数目对射流出口速度分布的影响.表明:在其他条件完全相同的情况下,一片振动膜时的激励器出口中心线上的平均速度和峰值速度,都较5片膜的情况小一半左右,而3片和5片压电膜时的激励器性能差别却不大.也就是说,虽然压电膜的数目增加能使激励器出口射流的能量增加,但这两者之间并非呈线性关系.此外还用PIV测量方法,直观地显示了射流出口的涡结构.      

某飞机系列粉末合金刹车盘改进技术的研究

通过改进整盘钢骨架两面烧结粉末合金刹车盘的结构,直接成形卸荷槽,取消冲卸荷槽工序,完全解决该刹车盘长期存在的在后续加工及使用过程中的掉块问题。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.