面向一体化计算的整体式液体冲压发动机建模及性能评估

为发展冲压发动机性能工程预估方法,建立了面向一体化计算的整体式液体冲压发动机性能计算模型,并使其兼容基团贡献算法,提高了拓展性。利用模型分析了冲压发动机在攻角0°～6°、高度0～18km、马赫数2.0～3.5、余气系数1.0～2.9范围工况多维度连续变化下,比冲、推力系数和燃油质量流量的速度-高度特性、高度-节流特性、节流-速度特性以及攻角特性。研究结果表明:性能计算模型可在一体化计算条件下、基团贡献算法允许范围内,不依赖试验数据对冲压发动机性能预估,计算结果与技术参考值相比相对误差均小于14%。推力系数和比冲具有基本一致的速度-高度特性和相似的高度-节流特性,受燃气组分影响,推力系数和比冲的节流-速度特性差异明显。燃油质量流量的变化规律不同于比冲和推力系数,在进入平流层后呈现折缓趋势,而呈现连续性,速度越大、高度越低、余气系数越小,燃油质量流量越高,反之则越小。引入攻角以后,攻角越大,比冲和推力系数越低,进气道起动马赫数越高;攻角-起动马赫数曲线小范围内近似线性,攻角超过5.6°非线性加剧。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

Corrosion mechanism investigation of TiN/Ti coating and TC4 alloy for aircraft compressor application

It is imperative to develop multifunctional erosion and corrosion resistant coatings for compressor blades of aircraft engines in harsh environment. PVD (Physical Vapor Deposition) technology has the advances in processing erosion-resistant coatings; however, the performance of PVD coatings to combat corrosion depends on various coating defects. Determining and comparing the corrosion performances of PVD TiN/Ti coating and uncoated TC4 alloy was the main objective of present work. The 960 h salt spray corrosion and 116 h hot corrosion tests were conducted to simulate the grounding and working environments of the aircraft compressors. The corrosion mechanisms due to the coating defects such as pinhole, columnar boundary and large grain were analyzed based on the OM, Confocal microscope, electrochemical measurements, SEM, XRD and EDS results. Owing to the disordered state associated with the columnar boundary and the coating defect, nitrogen could be easily replaced by oxygen in the hot corrosion process, these structures were channels for fast diffusion of oxygen. Moreover, the Gibbs energy changes of Ti oxidation and TiN oxidation were thermodynamically calculated according to the working condition of aircraft compressors, and considerable research effort was focused on mapping out the phase diagram of Ti, TiN and high pressure gases. The findings of this research can provide insights into developing multifunctional coatings for future aircraft engines.     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

石墨填料对浸渗热解-熔融浸渗方法制备的C/SiC复合材料结构和性能的影响

采用石墨树脂浆料浸渍三维针刺碳毡增强体,热解后得到C/C多孔体,并采用反应熔体浸渗法制备C/SiC复合材料.研究了石墨填料对C/C多孔体的结构以及C/SiC复合材料力学性能的影响.结果 表明,石墨树脂浆料浸渍时树脂填充束间小孔形成结构致密的亚结构单元,而石墨可以有效填充胎网层等大孔隙,一次浸渍热解后碳产率有效提高.所得...     

碳/碳复合材料表面纳米HAp/壳聚糖生物复合涂层的制备

以声化学法合成的纳米羟基磷灰石(HAp)为起始原料,以异丙醇作为分散介质,采用水热电泳沉积法在经壳聚糖(CS)溶液改性后的碳/碳复合材料(C/C)表面沉积纳米HAp/CS生物复合涂层.重点研究了水热条件下沉积电压对复合涂层的晶相组成、形貌和结构的影响规律.采用X-射线衍射仪(XRD)、透射电子显微镜(TEM)、傅立叶变换红外光谱分析仪(FTIR)和场发射扫描电子显微镜(FE-SEM)对所制备的涂层进行表征.结果表明:随着沉积电压的升高,涂层更加致密和均匀;同时水热环境有利于纳米HAp晶粒的生长,制备出的HAp/CS复合涂层不需要后续热处理.     

大型飞机迎角/过载限制器设计

根据典型大型飞机迎角/过载限制器的特点,提出了两种采用积分控制来减小静态误差的大型飞机迎角/过载保护方法,即最大值切换逻辑和加权过渡逻辑方法,深入研究了如何设计迎角/过载限制器参数,探讨了采用以上两种不同方法来进行迎角与过载限制器切换的优劣,系统仿真结果证明了所设计的限制器的有效性。该项研究为我国未来大型飞机如何设计迎角/过载限制器提供了部分理论依据。     

不同碳黑填料含量2D—SiCf／SiC复合材料介电及雷达吸波性能研究

对先驱体浸渍裂解工艺(PIP)制备的含碳黑填料2D-SiCf/SiC复合材料介电以及雷达吸波性能进行研究.研究表明,由于KD-Ⅰ型SiC纤维表面具有连续碳涂层,不能直接用于吸波材料,需通过空气热处理手段将其除去.对纤维表面去碳后制成的不同碳黑填料含量2D-SiCf/SiC复合材料微波介电常数进行测试,结果表明,随碳黑含量增加,复合材料介电常数明显增大,但由于碳黑的高比表面和先驱体溶液粘度的限制,复合材料中碳黑体积分数最大仅能达到7%～8%,介电常数难以继续增大,介电损耗低于0.3,并且介电常数频散效应不理想.对不同碳黑填料含量复合材料反射率进行计算,结果表明,单层复合材料在某一频段内具有较好的吸波性能,但由于复合材料介电常数频散效应较差,宽频吸波性能不理想,采用不同吸收剂含量复合材料层铺工艺可能可以解决吸波性能带宽问题.     

由喷嘴连接的燃烧室到供应系统压力振荡传递过程研究

为了研究在压力振荡由液体火箭发动机燃烧室传递到供应系统的过程中喷嘴所起的作用,从理论上分析了压力振荡由燃烧室到供应系统通过喷嘴的传递过程,推导了振荡传递过程的传递函数.讨论带有各种喷嘴的供应系统的动态特性,对供应系统管路长度、燃烧室压强、喷嘴种类、喷嘴压降及喷嘴结构尺寸对燃烧室压力振荡引起供应系统压力振荡的影响进行了计算,得到了喷嘴以及工况参数在传递过程中的影响规律.      

液氧/煤油补燃发动机低频频率特性研究

基于模块化层次化的建模技术,建立液氧/煤油补燃发动机的线性小扰动频率特性仿真模型.在建模过程中,重点考虑了绝热流动假设和熵波影响下的气路模型.依据交流流体网络理论,运用传递函数法分析了该型发动机的低频频率特性,为研究液体火箭的纵向耦合振动(POGO)及发动机动力学提供帮助.