气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。     

Mathematical description of the NaK model for MASTER-2005

The release of NaK droplets has been modeled for the new version of the European Meteoroid and Space Debris Terrestrial Environment Reference model MASTER-2005. Previously published versions of the model have been revised. The parameters of the model are introduced and discussed. NaK droplets consist of eutectic sodium–potassium alloy and have been released during RORSAT reactor core ejections. They contributed to the space debris environment in the centimeter and millimeter size regime. Sixteen nuclear powered RORSATs launched between 1980 and 1988 activated a reactor core ejection system in Sufficiently High Orbits (SHO), mostly between 900 and 950 km altitude. The core ejection caused an opening of the primary coolant circuit. The liquid coolant has been released into space during these core ejections. The outflow is considered as a discrete event for each of the sixteen core ejections in total. The NaK coolant has been forming droplets up to a diameter of 5.5 cm. NaK releases are restricted to a very narrow region near 65° inclination. This paper gives the parameters of the NaK release model as it is implemented in MASTER-2005. The quantitative values of all model parameters including characteristic diameter and uniformity parameter are presented. The ratio of the characteristic droplet size to the orifice diameter is discussed. It is estimated that altogether 128 kg of NaK-78 (8 kg per RORSAT) was released on orbit. Simulation runs show that there are still 45,000 droplets with a total mass of 97 kg in orbit at the reference epoch 1 May 2005, whereas the smallest droplet has a diameter of 5 mm. Results of orbit propagation simulation runs are presented in terms of spatial density.     

次流通道对双喉道气动矢量喷管的性能影响研究

为了进一步了解次流通道对双喉道气动矢量喷管(Dual Throat Nozzle,DTN)气动矢量性能的影响,基于二维DTN喷管构型进行了详细的数值模拟研究。结果表明:收扩的次流通道相对于平直的次流通道不会改善DTN喷管的推力矢量性能;随着次流流量增加,DTN的推力矢量角存在一个最大值,超过该值各推力矢量性能均会降低;次流通道宽度对DTN喷管推力矢量性能影响显著:(1)次流宽度不影响所能达到的最大推力矢量角;(2)小的次流宽度在进口总压较高的条件下具有更高的推力矢量角;(3)增大次流宽度能降低次流总压,但达到的矢量角会有所减小。     

一种用于液晶曝光中的激光检测系统

介绍了一种非接触式激光检测系统，可用于检测液晶曝光中液晶模板与基板之间的间隙，给出了该种系统的测量原理、硬件系统、信号处理方法、测量结果、分辨力和误差分析，并指出了这种测量系统的应用。     

Integration and calibration of a multi slit spectropolarimeter

Multi-slit spectropolarimeter is a next-generation spectropolarimeter to obtain vector magnetic field information at high spatial, spectral, and temporal resolution for studying the magnetic structures on the Sun. Once developed, it can be used as ground based instrument at solar observatories, also as a space payload for various solar missions. A high spectral resolution is invariably an important parameter for accurate vector magnetic field measurements and faster cadence is required for the study of dynamical evolution of structures (e.g., solar flares, sunspots etc.) on the Sun and hence better understanding on the physics behind their evolution.     

永磁同步电机无传感器转子位置观测器研究

永磁同步电机的运动是一个强耦合非线性动态过程,旋转高频电压注入下 的电机模型存在建模误差,数据采集存在测量噪声和系统噪声,采用传统的线性控制理 论难以达到要求。提出了以不依赖于准确数学模型的广义预测控制算法为基础的转子位 置观测器,可有效提高转子位置检测精度,增强抗干扰能力。仿真实验结果表明,在存 在建模误差和噪声的情况下,基于广义预测控制算法位置观测器的旋转高频注入法可准 确追踪转子位置。     

液膜法处理石化厂碱渣含酚废水的研究

本文研究了液膜法处理石化厂碱渣含酚废水的最佳制乳条件，最佳传质条件，并应用于不同浓度含酚水样处理。当挥发酚浓度低于７０００ＰＰｍ时，顷一级传质可使含酚量低于１００ＰＰｍ，７０００￣２００００ＰＰｍ，级二级传质可使含酚量低于１００ＰＰｍ，处理后废水可直接排放到石化厂和生化厂处理，为进一步进行中试研究提供了理论依据。     

跃变型介质中原油渗流有限元计算

本文建立跃变型介质中原油渗流的数学模型,可用来描述油层(尤其是低渗透层)超高压注水条件下的不稳定渗流过程及其特征。用Galerkin有限元法进行了数值计算,讨论了介质跃变的影响。     

火箭发动机基于神经网络非线性辨识的故障检测

应用神经网络方法，提出了一种液体火箭发动机故障实时检测算法。神经网络采用非线性辨识技术贴近发动机的工作过程，并输出包合发动机故障信息的辨识误差信号。若辨识误差变大超过一定阈值，检测逻辑就预报发动机故障。在发动机启动阶段离线训练神经网络，在发动机稳态过程可以采用离线或在线学习算法。实验研究表明神经网络可以成功地应用于大型泵压式液体火箭发动机的故障检测。