转动薄壁圆柱筒振动特性:有限元法与解析解的对比

采用解析法和有限元法,研究了科氏力和离心刚化效应对不同约束条件下转动薄壁圆柱筒结构振动特性的影响,并进行了对比分析.结果表明,与解析解相比,有限元法计算得到的静止状态薄壁圆柱筒结构固有频率因边界条件不同而存在不同的差异,其中两端简支边界条件下与解析解吻合较好.随转速增加,前后行波频率差值加大,曲线明显分离,而这种分离趋势随周向波数的增大而减小.由于离心刚化效应的存在,相比于只考虑科氏力的影响,转动薄壁圆柱筒的行波频率有增大的趋势,并且当转速和周向波数较大时,前后行波频率均会大于对应的静频率.      

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

MDS图在液态模锻工艺过程单片机仿真控制系统中的应用

本文介绍了液态模锻工艺过程单片机仿真控制系统的设计方法，包括液态模锻工艺程确立、逻辑量确立、硬件系统设计、ＭＤＳ图的建立及软件实现，在工艺设备的逻辑性控制中应用ＭＤＳ图控制结构设计的控制器可方便方便地实现ＰＬＣ的控制功能，也可主便地实现其他娄字逻辑系统的控制功能。     

Mathematical description of the NaK model for MASTER-2005

The release of NaK droplets has been modeled for the new version of the European Meteoroid and Space Debris Terrestrial Environment Reference model MASTER-2005. Previously published versions of the model have been revised. The parameters of the model are introduced and discussed. NaK droplets consist of eutectic sodium–potassium alloy and have been released during RORSAT reactor core ejections. They contributed to the space debris environment in the centimeter and millimeter size regime. Sixteen nuclear powered RORSATs launched between 1980 and 1988 activated a reactor core ejection system in Sufficiently High Orbits (SHO), mostly between 900 and 950 km altitude. The core ejection caused an opening of the primary coolant circuit. The liquid coolant has been released into space during these core ejections. The outflow is considered as a discrete event for each of the sixteen core ejections in total. The NaK coolant has been forming droplets up to a diameter of 5.5 cm. NaK releases are restricted to a very narrow region near 65° inclination. This paper gives the parameters of the NaK release model as it is implemented in MASTER-2005. The quantitative values of all model parameters including characteristic diameter and uniformity parameter are presented. The ratio of the characteristic droplet size to the orifice diameter is discussed. It is estimated that altogether 128 kg of NaK-78 (8 kg per RORSAT) was released on orbit. Simulation runs show that there are still 45,000 droplets with a total mass of 97 kg in orbit at the reference epoch 1 May 2005, whereas the smallest droplet has a diameter of 5 mm. Results of orbit propagation simulation runs are presented in terms of spatial density.     

中心承力筒数控加工工艺

通过制定合理的数控加工工艺方案,实现了中心承力筒的数控加工,有效保证了孔的加工精度和

表面质量,提高了零件的加工效率。通过在5 轴联动数控加工中心上实际加工,证明该数控加工工艺切实可

行。

     

UNLX系统下软件开发版本管理初探

在ＵＮＬＸ操作系统下开发软件，开发过程中容易出现版本管理的混乱，为解决此问题，应充分利用系统提供的ＲＣＳ或ＳＣＣＳ工具，结合ｓｈｅｌｌ程序，充分发挥版本管理的作用。     

一种用于液晶曝光中的激光检测系统

介绍了一种非接触式激光检测系统，可用于检测液晶曝光中液晶模板与基板之间的间隙，给出了该种系统的测量原理、硬件系统、信号处理方法、测量结果、分辨力和误差分析，并指出了这种测量系统的应用。     

Integration and calibration of a multi slit spectropolarimeter

Multi-slit spectropolarimeter is a next-generation spectropolarimeter to obtain vector magnetic field information at high spatial, spectral, and temporal resolution for studying the magnetic structures on the Sun. Once developed, it can be used as ground based instrument at solar observatories, also as a space payload for various solar missions. A high spectral resolution is invariably an important parameter for accurate vector magnetic field measurements and faster cadence is required for the study of dynamical evolution of structures (e.g., solar flares, sunspots etc.) on the Sun and hence better understanding on the physics behind their evolution.     

钛合金熔模精铸氧化锆陶瓷型壳／金属界面反应研究

通过实际浇注和真空扩散连接分别制取了钛／型壳界面，借助ＳＥＭ、ＥＰＭＡ和显微硬度仪等分析测试手段对所得界面进行了深入研究，初步提出了以Ｚｒ、Ｏ元素向钛基体内的扩散为主导的界面反应机制。实验结果表明，界面反应并非在整个界面上均衡推进，而是在浓度、温度、能量起伏、以及陶瓷颗粒位向适宜的区域优先发生界面反应