钛合金线性摩擦焊接头缺陷形成机理分析

采用热力耦合技术,建立了线性摩擦焊过程的有限元模型,计算了焊接温度、应力和变形场,并对温度场进行了试验验证.观测了接头不同缺陷的微观形态,并对其形成机理进行了分析.最后,提出了控制焊接缺陷的措施.     

摩擦时间对异质钛合金线性摩擦焊接头微观组织的影响

采用光学显微镜和扫描电镜研究TC11与TC17异质钛合金线性摩擦焊接头微观组织的特点.结果表明,在振幅为3mm、频率为40Hz、摩擦压力为66.7MPa、顶锻压力为80MPa、顶锻时间为30s的条件下,随着摩擦时间的延长,初生β相动态再结晶晶粒尺寸和α相片层宽度增加.在同一接头内部,接头表面的β相动态再结晶晶粒尺寸比接...     

TC4钛合金盘铣开槽加工残余应力

整体叶盘盘铣开槽加工过程中铣削力大,铣削温度高,会在加工表面表成较深的残余应力层,对零件的疲劳寿命造成严重影响。为提高零件的疲劳寿命,本文以钛合金试块为研究对象,利用残余应力测试分析系统测量表面残余应力,利用拨层法测量次表面的残余应力,采用线性回归技术建立残余应力预测模型,并利用极差分析法分析工艺参数对残余应力的影响规律。试验结果表明:盘铣表面均为压应力,且轮毂面上的残余应力大于叶盆叶背面上的残余应力,均由挤光效应引起;回归预测模型的显著性水平为0. 01,其回归效果良好;各因素对σAx、σAy(σAx、σAy分别表示轮毂面x、y方向残余应力)的影响程度依次为主轴转速>进给速度>切削深度;对σBx(σBx表示叶盆叶背面x方向上的残余应力)的影响程度依次为主轴转速>切削深度>进给速度;残余应力纵向均为压应力,轮毂面上的分布深度为230~270μm,叶盆叶背面上的分布深度为170~175μm。     

飞行器线性分式变换建模及其降阶研究

针对一类可用线性变参数系统描述的飞行器动力学模型,本文采用图形法建立其线性分式变换模型,并应用卡尔曼规范分解对模型进行降阶.最终得到的模型将飞行器动力学明确分解为确定性部分和时变参数部分.数学仿真验证了所建立模型的正确性.     

LTPB多站点联网测试软件设计

作为现役飞机最为先进航电技术的代表，高速数据总线在设计上的复杂性是显而易见的。如何对其性能进行全面考察是一个非常重要的问题。本文所论述的联网测试软件提供了一个有效的方法，实现了对LTPB联网性能的测试与演示。一方面证明了软件本身设计的合理笥，同时也进一步证明了整个LTPB设计与实施的正确性。     

压缩式压电传感器轴向灵敏度的幅值线性度问题

本文了压电传感器的结构原理,说明了压电传感器幅值灵敏度的线性问题,分析了正反向灵敏度的差异和“饱和现象”,以便在生产、鉴定与使用时加以注意。     

Comprehensive outage compensation of real-time orbit and clock corrections with broadcast ephemeris for ambiguity-fixed precise point positioning

The main challenge in real-time precise point positioning (PPP) is that the data outages or large time lags in receiving precise orbit and clock corrections greatly degrade the continuity and real-time performance of PPP positioning. To solve this problem, instead of directly predicting orbit and clock corrections in previous researches, this paper presents an alternative approach of generating combined corrections including orbit error, satellite clock and receiver-related error with broadcast ephemeris. Using ambiguities and satellite fractional-cycle biases (FCBs) of previous epoch and the short-term predicted tropospheric delay through linear extrapolation model (LEM), combined corrections at current epoch are retrieved and weighted with multiple reference stations, and further broadcast to user for continuous enhanced positioning during outages of orbit and clock corrections. To validate the proposed method, two reference station network with different inter-station distance from National Geodetic Survey (NGS) network are used for experiments with six different time lags (i.e., 5 s, 10 s, 15 s, 30 s, 45 s and 60 s), and one set of data collected by unmanned aerial vehicle (UAV) is also used. The performance of LEM is investigated, and the troposphere prediction accuracy of low elevation (e.g., 10–20degrees) satellites has been improved by 44.1% to 79.0%. The average accuracy of combined corrections before and after LEM is used is improved by 12.5% to 77.3%. Without LEM, an accuracy of 2–3 cm can be maintained only in case of small time lags, while the accuracies with LEM are all better than 2 cm in case of different time lags. The performance of simulated kinematic PPP at user end is assessed in terms of positioning accuracy and epoch fix rate. In case of different time lags, after LEM is used, the average accuracy in horizontal direction is better than 3 cm, and the accuracy in up direction is better than 5 cm. At the same time, the epoch fix rate has also increased to varying degrees. The results of the UAV data show that in real kinematic environment, the proposed method can still maintain a positioning accuracy of several centimeters in case of 20 s time lag.     

Gain self-scheduled H_∞ control for morphing aircraft in the wing transition process based on an LPV model

This article investigates gain self-scheduled H 1 robust control system design for a tailless fold- ing-wing morphing aircraft in the wing shape varying process. During the wing morphing phase, the aircraft’s dynamic response will be governed by time-varying aerodynamic forces and moments. Nonlinear dynamic equations of the morphing aircraft are linearized by using Jacobian linearization approach, and a linear parameter varying (LPV) model of the morphing aircraft in wing folding is obtained. A multi-loop controller for the morphing aircraft is formulated to guarantee stability for the wing shape transition process. The proposed controller uses a set of inner-loop gains to provide stability using classical techniques, whereas a gain self-scheduled H 1 outer-loop controller is devised to guarantee a specific level of robust stability and performance for the time-varying dynamics. The closed-loop simulations show that speed and altitude vary slightly during the whole wing folding process, and they converge rapidly after the process ends. This proves that the gain self-scheduled H 1 robust controller can guarantee a satisfactory dynamic performance for the morphing aircraft during the whole wing shape transition process. Finally, the flight control system’s robustness for the wing folding process is verified according to uncertainties of the aerodynamic parameters in the nonlinear model.     

An approach for parameter estimation of combined CPPM and LFM radar signal

In this paper, the problem of parameter estimation of the combined radar signal adopting chaotic pulse position modulation (CPPM) and linear frequency modulation (LFM), which can be widely used in electronic countermeasures, is addressed. An approach is proposed to estimate the initial frequency and chirp rate of the combined signal by exploiting the second-order cyclostationarity of the intra-pulse signal. In addition, under the condition of the equal pulse width, the pulse repetition interval (PRI) of the combined signal is predicted using the low-order Volterra adaptive filter. Simulations demonstrate that the proposed cyclic autocorrelation Hough transform (CHT) algorithm is theoretically tolerant to additive white Gaussian noise. When the value of signal noise to ratio (SNR) is less than 4 dB, it can still estimate the intra-pulse parameters well. When SNR = 3 dB, a good prediction of the PRI sequence can be achieved by the Volterra adaptive filter algorithm, even only 100 training samples.     

线加速度台中稳速台转动对随动台定位稳定性的影响

针对线加速度台用于加速度计测试时,随动台定位受稳速台旋转干扰的现象进行了分析,提出被测设备质量要在负载允许范围内,使设备质心尽可能靠近随动台回转中心,并对其配平,以使稳速台转动带来的干扰力矩大大降低,保证测试中随动台的定位准确度及稳定性。