基于PXI的液体姿轨控火箭发动机试验测控系统设计与实现

针对液体姿轨控火箭发动机地面试验高精度、高风险和灵活多变的特点,设计研发了一套以PXI （PCI extensions for instrumentation）控制器为主体的发动机试验测控系统.控制系统拥有40路开关量控制能力,综合运用手动、时序和自动控制方式.测量系统拥有120路信号同步采集能力,具备故障诊断功能.测控系统软件使用LabVIEW开发,通用性良好.为增强控制可靠性,设计了面向工艺流程的试验面板,应用嵌入式控制,进行信号多级监测并引入紧急自动关机控制.为提高测量精度,对测量参数进行原位标定,提出了一种改进的干扰消除电路.该系统已多次成功应用于液体姿轨控火箭发动机地面试验,采用的设计方法有效地提高了测控系统的可靠性,测量精度和控制精度分别达到0.5%和0.1ms,能够充分满足多种类型的液体姿轨控火箭发动机对试验测控系统的要求.     

高速电弧喷涂FeNiCrAl涂层制备工艺对涂层性能影响

FeNiCrAl涂层是一种用作轴类零部件的表面耐磨防护材料,为深入研究高速电弧喷涂工艺对FeNiCrAl涂层性能的影响机理,对不同喷涂参数下制备的涂层的组织结构、结合强度、物相组成和显微硬度等性能进行分析表征,探究“喷涂电流-涂层组织结构-结合强度”之间的关系。结果表明：喷涂电流对涂层的组织致密性及结合强度影响较大;喷涂电流200 A、电压34 V、喷涂距离160 mm的工艺参数下制备的FeNiCrAl涂层组织致密,孔隙率约8.76%,结合强度52.3 MPa,涂层硬度约626 HV0.1,约为基体硬度的1.6倍;影响机理与Fe-Al金属间化合物和Cr0.19 Fe0.1 Ni0.11固溶体在涂层内部均匀弥散分布有关。     

现代机床在机测量技术研究与发展趋势

介绍了现代机床在机测量系统的基本构成、功能和效能,以及普通数控加工、超精密加工和复杂曲面及特殊结构工件加工3类场合在机测量系统的特点.阐述了在机测量系统核心技术——测头技术,重点讨论了各类测头的工作原理、特性、控制系统要求,以及适用场合.最后,提出了在机测量系统未来发展方向.     

智能机床的误差补偿技术

误差补偿技术是智能机床精度提高与保持的关键技术之一.分析了国内外机床误差补偿技术研究现状,提出智能机床误差补偿技术总框架;总结了智能机床误差源、误差元素、几何与热误差的误差元素模型及建模方法,以及典型的误差补偿方法;研究了力误差补偿技术、基于零件在线测量的误差综合补偿技术;最后,对未来智能机床误差补偿技术的发展重点进行展望.     

热处理对激光增材制造Ti2AlNb基合金组织及性能的影响

利用激光增材制造技术制备出Ti-22Al-25Nb合金薄壁试样,分析了沉积态和热处理态试样的宏观形貌、相组成和显微组织,以及不同制度热处理态试样的组织和室温拉伸性能.结果表明,沉积态试样相组成沿沉积高度方向呈现由B2+O+α2→B2+O→B2的变化趋势;热处理态试样的微观组织和相组成均匀,由B2、O、α23相组成;经930℃保温2h空冷的固溶处理和800℃保温24h空冷的时效处理后,合金室温拉伸性能好,抗拉强度为1017MPa,断后伸长率为6.0％.     

A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

A dimension reduced INS/VNS integrated navigation method for planetary rovers

Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods.     

叶尖粗糙度与倾角对光纤传感器输出特性影响

航空发动机涡轮叶片叶尖间隙变化影响发动机效率也蕴含丰富的发动机健康状态信息。实际叶尖间隙变化表现为3维变化,且叶尖表面受高温气流剥蚀等影响表面粗糙度发生变化。为探究其对光纤传感器测量叶尖间隙精度的影响,利用ZEMAX光学仿真软件分析了双圈同轴式光纤传感器在叶尖表面粗糙度变化和倾角变化影响下的输出特性,并搭建3维叶尖间隙静态标定平台对上述影响进行试验。结果表明:粗糙度和倾角增大均导致传感器灵敏度降低、零点位置后移。该结果为实现叶尖间隙变化的3维精确测量提供理论和试验依据。     

视觉导航技术的发展

近20年来视觉导航技术发展迅速,在原理方法与技术实现上取得了重要突破,规模化应用已经成为可能。以视觉导航中光流、视觉里程计、视觉同步定位与地图构建等主流研究方向为对象,对其发展概况、基本原理、技术优势与难点等进行了简要介绍与分析,并从近期应用推广及长远发展角度对视觉及视觉组合导航技术进行了展望。     

半球谐振陀螺研究现状与发展趋势

半球谐振陀螺是基于哥氏效应测量角速度的新型固态陀螺,具有结构简单、精度高、功耗低、寿命长、可靠性好、抗空间辐射等优点,是捷联惯性导航系统的理想陀螺仪,在宇航领域具有独特的应用优势。半球谐振陀螺的理论精度不受量子尺寸效应限制,是高精度、微型化陀螺的重要发展方向之一。首先介绍了半球谐振陀螺的基本工作原理,其次介绍了半球谐振陀螺的发展历程,综述了半球谐振陀螺的国内外研究现状,最后对半球谐振陀螺的发展趋势进行了展望。