Lift enhancement based on virtual aerodynamic shape using a dual synthetic jet actuator

The Dual Synthetic Jet Actuator (DSJA) is used to develop a new type of lift enhancement device based on circulation control, and to control the flow over the two-dimensional (2D) NACA0015 airfoil. The lift enhancement device is composed of a DSJA and a rounded trailing edge (Coanda surface). The two outlets of the DSJA eject two jets (Jet 1 and Jet 2). Jet 1 ejects from the upper trailing edge, which increases the circulation of airfoil with the help of the Coanda surface. Jet 2 ejects from the lower trailing edge, which acts as a virtual flap. The Reynolds number based on the airfoil chord length and free flow velocity is 250000. The results indicate that the circulation control method based on Dual Synthetic Jet (DSJ) has good performance in lift enhancement, whose control effect is closely related to momentum coefficient and reduced frequency. With the increase of the reduced frequency, the control effect of the lift enhancement is slightly reduced. As the momentum coefficient increases, the control effect becomes better. When the angle of attack is greater than 4°, the increments of lift coefficients under the control of DSJ are larger than those under the control of the steady blowing at a same momentum coefficient. The maximum lift augmentation efficiency can reach 47 when the momentum coefficient is 0.02, which is higher than the value in the case with steady blowing jet circulation control.     

加工装配误差影响下偏转射流压力伺服阀静态特性分析

电液压力伺服阀是电液压力伺服控制系统的核心控制元件，广泛应用于航空、航天、军事等领域。区别于流量伺服阀，压力伺服阀在滑阀放大器的设计上多采用带有压力控制容腔的三通阀结构，不同的滑阀结构使得现有的偏转射流流量伺服阀仿真模型难以满足压力伺服阀性能预测的需求。本文基于AMESim平台建立了偏转射流压力伺服阀的仿真模型，并通过实验对仿真模型进行了验证，验证结果表明仿真模型能够准确地描述压力伺服阀的静态特性。最后，通过仿真模型分析了加工装配误差影响下压力伺服阀输出性能差异，仿真结果可为偏转射流压力伺服阀的性能预测和结构设计提供参考。     

Pressure performance for a thin-walled ring and turbulent-jet orifice modeled elastic squeeze film damper

This paper explores an analytical model for Elastic Ring Squeeze Film Damper (ERSFD) with thin-walled ring and turbulent-jet orifices, and uncovers its Oil Film Pressure Performance (OFPP). Firstly, the ring deformation is addressed by using the Fourier series expansion approach and the orifice outflow rate is characterized with the Prandtl boundary layer theory. Secondly, applying finite difference scheme, the influence of elastic ring flexibility, orifice diameter, and attitude angle on the OFPP is analyzed. Finally, Outer chamber pressure was measured experimentally at different rotor speeds. The results indicate that the outer chamber pressure coats an individual load-carrying region and spreads symmetrically pertaining to the attitude angle. Its amplitude drops as the elastic ring flexibility decreases but boosts with the reduction of the orifice diameter. For inner chamber pressure, the orifice diameter effects a similar trend to the outer cavity, but exhibits more stable distribution regarding the attitude angle. Minimizing the elastic ring flexibility causes an increase in amplitude. The model is validated by the test results giving that the outer chamber pressure shifts synchronously and periodically with the variation of the attitude angle, while the pressure amplitude increases slightly at higher rotor speeds.     

Improving performance of macro electrolyte jet machining of TC4 titanium alloy: Experimental and numerical studies

Electrolyte jet machining (EJM) is a promising method for shaping titanium alloys due to its lack of tool wear, thermal and residual stress, and cracks and burrs. Recently, macro-EJM has attracted increasing attention for its high efficiency in machining wide grooves or planes. However, macro-EJM generates large amounts of electrolytic products, thereby increasing the difficulty of rapid product removal with a standard tool and reducing the surface quality. Therefore, for enhanced product transport, a novel tool with a back inclined end face was proposed for macro-EJM of TC4 titanium alloy. For comparison, also proposed were ones with a standard flat end face, a front inclined end face, and both front and back inclined end faces. The flow field distributions of all proposed tools were simulated numerically, and experiments were also conducted to validate the simulation results. The results show that one with a 5° back inclined end face can decrease the low-velocity flow zone in the machining area and increase the high-velocity flow zone at the back end of tool, thereby promoting rapid product removal. A relatively smooth bright-white groove surface was obtained. The same tool also resulted in the highest machining depth and material removal rate among the tested ones. In addition, rapid product removal was beneficial to the subsequent processing. Because of its rapid product removal, the machining depth and material removal rate during deep groove machining using the tool with a 5° back inclined end face were respectively 7% and 14% higher than those produced using a standard one. Moreover, the lowest bottom height difference of 0.027 mm can be obtained when the step-over value was 8.2 mm, and a plane with a depth of 0.285 mm and a bottom height difference of 0.03 mm was fabricated using the tool with a 5° back inclined end face.