面向空间应用的单向微膨胀型热开关特性分析

为了提高探测器等航天器的温度控制精度,降低热波动造成的影响,基于金属的热胀冷缩原理设计了一种单向膨胀型热开关,利用二维稳态导热原理进行建模分析,得到热开关热特性参数。搭建了试验平台模拟热开关工作环境,测定不同功率条件下热开关的工作状态以及相关性能参数。当加热功率为04W时开关断开热阻为23046K/W;功率为30W时开关的导通热阻为03022K/W,开关控制比为7626。结果表明,试验数据与理论计算数据吻合较好,进一步说明了热开关的结构合理性以及适用性。     

微重力条件下热管吸热器瞬态热分析

基于微重力条件下的导热控制微分方程,采用焓法对热管吸热器相变材料容器进行了二维数值建模与仿真,在同时考虑空穴和相变的情况下,对微重力条件下蓄热单元相变传热进行了模拟计算,分析了空穴率对蓄热容器内部的温度场和热性能的影响,并将计算结果同美国航空航天局（NASA）方案热管吸热器蓄热单元相变传热计算结果进行了比较,验证了文中微重力条件下计算模型的合理性与准确性。研究结果表明：空穴影响着蓄热单元相变的进程,空穴的存在增加了容器内部的温度梯度,使得容器的蓄热能力降低;由于热管径向温差较小,热管壁温在相变材料熔点附近变化较小,从而在一定程度上能缓解热斑和热松脱现象。     

前缘射流对涡轮导叶吸力面多排气膜孔冷却特性的影响

为了研究前缘射流对吸力面多排气膜孔下游冷却特性的影响,在跨声速风洞中进行了实验并采用热电偶获得了气膜冷却效率和换热系数。叶栅进口雷诺数的范围为2.0×105 ~ 4.0×105,出口等熵马赫数为0.95,叶栅前的湍流度小于5%。前缘布置6排对冲圆柱孔,质量流量比的范围为2.00% ~ 3.71%,吸力面布置4排圆柱孔,质量流量比的范围为2.02% ~ 3.74%。实验结果表明：在没有前缘射流时,吸力面的气膜冷却效率随质量流量比增大先升高后下降,存在前缘射流时,质量流量比对气膜冷却效率的影响较小。对所有的工况而言,质量流量比增大都提高了吸力面的换热系数。相比于没有前缘射流的工况,前缘射流显著提高了吸力面孔排附近区域的气膜冷却效率并略微降低了换热系数;在吸力面后半段,前缘射流显著提高了换热系数而对气膜冷却效率影响较小。总的来说,前缘射流改善了吸力面孔排附近区域的冷却效果,但是恶化了吸力面后半段区域的冷却效果。     

浮升力对竖直上升圆管内超临界航空煤油换热的影响及评价准则

为深入理解航空发动机再生冷却热防护中的换热机理,对竖直上升圆管内超临界压力RP-3航空煤油的传热恶化开展了实验研究。探究了两类传热恶化的换热特征和形成机理,考察了热流密度、质量流量和进口压力对传热恶化的影响机制。获得了两类传热恶化的起始条件判别准则。以Nu/Nu0=0.75作为依据,建立了浮升力影响评价准则。通过格拉晓夫数修正实现了换热关联式预测。结果表明：两类传热恶化出现在不同条件下,低温区传热恶化源于边界层转捩和浮升力的综合作用,当进口雷诺数高于5730时其不再出现;高温区传热恶化的临界热流密度可以表述为质量流量的函数关系。当浮升力参数Grb/Re2.7和Gr/Re2分别高于10-7、10-3时,浮升力作用不可忽略。改进的换热关联式具有合理的预测精度,满足热防护系统设计的工程运用。     

Whole-process modeling of titanium disc forming for gradient distributions of temperature and deformation

Gradient distributions of temperature and deformation (GDTD) are crucial for achieving dual-performance discs of titanium alloys which is required by the service environment of aeroengine. However, heating, cooling and deforming sequence in the whole process of the titanium disc forming, which leads to difficulties for achieving GDTD due to a lot of parameters. To solve this problem, a whole-process model of the titanium disc forming for GDTD has been established. In the model, heating and cooling via heat radiation, conduction and convection, and deforming by local loading with mold chilling are all considered. Experiments on heating and cooling as well as deforming were carried out by using a furnace and the Gleeble-3500 machine. The experimental data are used to determine thermal parameters and constitutive relations of the IMI834 titanium alloy, and then to verify the reliability of the model. Then the model was used to simulate the evolution rules of temperature and deformation of the titanium disc. The results show that the heating surface, furnace temperature, billet profile and loading rate play the core role for the control of GDTD, and thus a set of parameters were determined. Therefore, this work provides a base for developing a new forming technology of the dual-performance titanium discs with the approach of local heating and local loading.     

Numerical simulation of compression corner flows at Mach number 9

A hypersonic vehicle encounters a wide range of conditions during its complete flight regime. These flight conditions may vary from low to high Mach numbers with varying angles of attack. The near-wall viscous dissipation associated with flows at combined high Mach and Reynolds numbers leads to significant wall heat transfer rates and shear stresses. The shock wave/boundary-layer interaction results in a flow separation region, which commonly augments total pressure losses in the flow and lowers the efficiency of aerodynamic control surfaces such as fins installed on a vehicle. The standard turbulence models, when used to resolve such flows, result in incorrect separation bubble size for large separated flows. Therefore, it results in an inaccurate aerodynamic load, such as the wall pressures, skin friction distribution, and heat transfer rate. In previous studies, the application of the shock-unsteadiness correction to the standard two-equation k-ω turbulence model improved the separation bubble size leading to an accurate pressure prediction and shock definition with the assumption of constant Prandtl number. In the present work, the new shock-unsteadiness modification to the k-ω turbulence model is applied to the hypersonic compression corner flows. This new model with variable Prandtl number is based on the model parameter, which depends upon the local density ratio. The computed wall pressures, heat flux and flow field are compared to the experimental data. A parametric study is carried out by varying compression deflection angles, free stream Reynolds number and wall temperatures to compute the flow field and wall data accurately, particularly in the shock boundary layer interaction region. The new shock-unsteadiness modified k-ω model with variable Prandtl number shows an accurate prediction of initial pressure rise location, pressure distribution in the plateau region and heat flux in comparison to the standard k-ω model.     

A refined design method for precoolers with consideration of multi-parameter variations based on low-dimensional analysis

The precooler is a distinctive component of precooled air-breathing engines but constitutes a challenge to conventional thermal design methods. The latter are based upon assumptions that often reveal to be limited for precooler design. In this paper, a refined design method considering the variations of fluid thermophysical properties, flow area and thermal parameters distortion,was proposed to remediate their limitations. Firstly, the precooler was discretized into a fixed number of sub-microtu...     

卫星空间外热流轨道参数ψ_0,Ω_0和ω_0计算

文章给出了卫星热分析空间外热流计算中所需要的轨道参数太阳黄经、升交点赤经和近地点幅角的初值φ_0、Ω_0、ω_0 的计算公式。其精确度满足卫星热分析要求。     

扇形和圆形气膜冷却孔的流动和传热实验比较

首次对流向倾角α为60°、锥顶角γ分别为15°和30°的扇形气膜冷却喷孔射流下游的流动和传热进行了详细的实验研究,并与相同实验条件下圆孔射流的情形进行了比较,结果发现了扇形孔优越的气膜冷却性能和其下游速度边界层等值线的3种基本形态。      

加罩转—静盘系的换热—换质实验研究

应用传热-传质类比原理于加罩转-静盘系统,通过盘缘轴向进气实验模型的研究,用萘升华法得到加罩转-静盘系旋转盘表面的局部和平均换质规律,从而类比出旋转盘的局部和平均的换热规律。文章分析了系统的几何尺寸(主要是间隙比G_c、间距比G_s)、旋转雷诺数Reθ和流量系数C_w对换质的影响。并用实验方法给出准则关系式,且对这种研究方法给出了误差分析结果。