一种摩擦阻尼器在整体叶盘结构的应用

介绍了一种应用于整体叶盘结构的摩擦阻尼器,即在轮缘下方加工销孔,安装阻尼销.工作时,由于离心载荷的作用,阻尼销与轮缘相互摩擦,从而消耗振动能量.这种阻尼器被应用于两台发动机的涡轮整体叶盘减振方案中,试验结果显示:其减振效率差异较大.数值模拟分析证明,这种阻尼器的减振效率和振动能量在叶-盘间的传递有关.对于叶-盘强耦合振型,这种阻尼器可以获取较高的减振效率,叶片振动应力水平下降了约70%;但对于叶-盘弱耦合振型,叶片振动应力幅值没有明显下降趋势.      

辐射换热对平板气膜冷却性能影响

为了分析辐射换热对平板气膜冷却性能的影响,分别对不考虑辐射换热(耦合计算)与考虑辐射换热两种条件下的平板隔热屏进行了三维流热耦合数值模拟研究,并与绝热壁(不考虑隔热屏固壁导热)的计算结果进行了对比。辐射换热采用离散坐标法。得到了3种不同主/次流总温比(Rt)条件下气膜冷却效果、流场、单位面积冷流体热负荷以及流量系数的对比结果与变化规律。结果表明:气膜冷却效果沿流向逐渐降低,且随总温比的增加而降低;在展向上气膜冷却效果呈现中间高两边低的分布规律,最大与最小相对值在绝热壁条件下达到最大,为94.5%,辐射换热次之,为13.5%,不考虑辐射换热时最小,为9.8%。与不考虑辐射换热结果相比,辐射换热对气膜冷却效果的影响在流动方向逐渐变大,气膜孔附近展向温度梯度增大,冷流体热负荷增加了92.8%,二者计算的流量系数相差不大,为1.1%,与绝热壁计算结果相比,流量系数减小了13.1%。随着总温比增加流量系数减小,最大值与最小值相差不大,为1.1%。     

A swept fin-induced flow field with different height mounting gaps

In order to apply the air fin successfully and ensure the maneuverability of hypersonic vehicle, a key problem to be studied urgently is the heat flux brought by the fin mounting gap. The appearance of mounting gap and fin shaft can induce many complex flow structures which need more attentions to be investigated. Under Ma 6, Nano-tracer-based Planar Laser Scattering (NPLS) and Temperature Sensitive Paints (TSP) were applied to visualize and measure transient flow structures and heat flux distribution of a swept fin-induced flow field with different height mounting gaps. Complementarily, Reynolds-averaged N-S equations were solved with k-ω SST turbulent model. The heat flux distribution results of numerical simulation and TSP observed the change of high heat flux region with different mounting gap, both in position and magnitude. The streamlines based on Computational Fluid Dynamics (CFD) and flow visualization results obtained by NPLS revealed the cause of high heat flux region. The high heat flux region in this flow field is mainly related to the reattachment of vortex and flow stagnation. The increase of gap height can lead to stronger gap overflow and shaft-induced horseshoe vortex, which are source of the high heat flux around the fin. The case with the highest mounting gap (4 mm) en-counters the most severe aerodynamic heating, both on the surface of fin and plate. Thus, under the premise of ensuring the flexibility of the fin, the gap should be set as small as possible.     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

舱内航天服散热途径分析

为分析常压下航天员穿着舱内航天服时的散热性能，６名健康男性青年按二次复合设计分组共进行２４人次试验，经分析计算了获得了服装各散热途径的散热率随通风气源参数及人体活动水平变化的数学模型。对影响服装散热性能的因素及服装散热特性进行了分析讨论。     

热管式表面温度计检定装置

叙述一种热管式表面温度计检定装置的原理、结构。该装置可用于航天领域在实验室条件下对表面温度计的检定。     

一种尾流消散动态预测的改进算法

尾流间隔是增大跑道容量的主要限制因素之一，为了在保持安全水平的前提下有效地增大跑道容量，可以对尾流消散进行动态预测，并据此缩减尾流间隔。研究了一种尾涡消散动态预测算法，该算法考虑了真实大气的大气分层、湍流、侧风、迎面风、风切变以及地效影响，并用一阶后向差分对该算法进行了离散化改进；在改进算法的基础上，时进近阶段尾流的消散在Matlab中进行了仿真计算；计算结果复现了尾涡的下沉现象和侧风对尾涡传输的线性累积效应。     

热流限制下的最优气动力辅助变轨

以变轨能量消耗最小为优化目标，应用极大值原理研究了飞行过程受热流限制和升力系统约束下的气动力辅助共面变轨问题，飞行过程成分第一自由弧段，约束弧段，第二自由弧段三个部分，讨论了升力系数的最优表达式，分析了飞行过程中两种约束的相互作用，给出了约束弧起始位置的角点条件和终端的横截条件下，对不同的初值选取方法讨论了三种计算策略，并给出了数值算例。     

超燃冲压发动机燃烧室主动冷却设计研究

超燃冲压发动机燃烧室主动冷却模型制造和热考核试验的费用高昂、周期长,为了降低试验风险,采用三维计算和经济的验证试验相结合的方法开展了超燃冲压发动机燃烧室主动冷却设计。冷却结构基本参数设计和侧壁冷却流动设计是确定设计方案的两大基础,前者采用三维传热计算结合冷却面板传热验证试验完成,后者采用超临界燃料流动三维并行计算结合水流动验证试验完成。在此基础上,经过多轮的结构设计与三维传热及强度计算评估迭代,确定了最终的燃烧室主动冷却结构。设计的主动冷却燃烧室在来流马赫数2.5,总温1700K条件下成功通过200s热考核试验,表明所采用的设计方法、验证试验和计算工具是有效和可信的。     

轻质隔热纳米孔结构耐烧蚀酚醛材料

在一定温度下,通过改性剂组分与热固性钡酚醛树脂之间热共聚反应,制备了改性酚醛树脂。采
用模压工艺制备出具有目标尺寸和形状的改性酚醛树脂固化物,对该样品分别进行了400 和700℃的炭化处
理,得到了相应的酚醛炭化样品,并测试其密度、失重率、收缩率等特征参数。研究改性剂用量对碳化物特征参
数和性能的影响,如密度、失重率形貌、比表面积、隔热性能、压缩强度等。SEM 研究表明,700℃炭化后样品形
成了“珊瑚状”碳结构,形成了30 ~150 nm 纳米孔。比表面积测试(BET)结果表明其比表面积可达464 m2 / g。
隔热性能与力学性能的测试结果表明,相对于未改性酚醛树脂碳化物,改性酚醛碳化物的热导率降低了
45． 57%,并且保持了较好的压缩强度。