Bursts in the HETE-2 catalogue

We have studied a set of GRBs detected by HETE-2 satellite with special focus on low-energy part of the spectrum. Results of data reduction procedures of different members of the HETE collaboration were combined with other publicly available information creating a concise catalogue. A more detailed analysis of lightcurves of the prompt emission was performed using data from FREGATE instrument.     

基于T-S模糊模型的模糊大系统的混合滤波

针对非线性大系统内部过程参数的检测估计,采用连续模糊大系统模型,利用lyapunov定理和分布式处理方法,给出了模糊大系统的H2/H∞混合滤波器设计方法。该方法在保证滤波误差系统全局稳定的同时,具备了H2/H∞性能。通过求解线性矩阵不等式,可以得到滤波器参数。最后,用一个数值例子验证了该方法的正确性和有效性。     

基于TC783A的三相电动机缺相保护电路的设计与实现

介绍用于三相电动机缺相保护装置的设计方法,采用集成芯片TC783A为核心元件实现,有效地解决三相电动机其他保护元件的局限性。具有快速切断控制回路电源的功能及缺相指示和相序指示,试验证明系统工作性能良好。     

A319飞机APU启动故障可靠性调查

本文对A319飞机131-9A型APU启动不正常事件进行可靠性调查,对APU启动故障统计分析,对影响启动的部件采取如下措施:老式启动保险6KA质量差主动更换且飞机上配备6KA;启动马达-3构型降级为-2以提高寿命,后续再升级至更高寿命的-4构型;执行改装加长启动线路以降低启动电流;点火激励器软时限控制定期拆下送厂检测。通过针对性措施,有效减少了APU启动不正常事件的发生。     

Ionospheric F2-Layer critical frequency retrieved from COSMIC radio occultation: A statistical comparison with measurements from a meridional ionosonde chain over Southeast Asia

In this paper, we compared the F2-Layer critical frequency (foF2) derived from FORMOSAT-3/COSMIC radio occultation (RO) and ionosondes at Chiang Mai, Chumphon and Kototabang during the years 2008–2015 to evaluate the performance of COSMIC RO over Southeast Asia region. The results show that the time development of foF2 values derived from COSMIC RO generally agrees well with those from ionosonde measurements. However, the differences between the foF2 derived from COSMIC RO and that derived from ionosonde observations display latitudinal dependence. COSMIC RO tends to underestimate foF2 at Chiang Mai and Kototabang, which is near to the north EIA crest and the south one, respectively, while a little overestimate foF2 at Chumphon, which is close to the geomagnetic equator. COSMIC RO agrees best with ionosonde at Chumphon and worst at Chiang Mai. At each ionosonde station, the quality of COSMIC RO data degrades with the increase of solar activity. In addition, at the station Chiang Mai and Kototabang, COSMIC RO performs better in summer than in equinox and winter. Furthermore, the differences in foF2 derived from COSMIC RO and that from ionosonde measurements vary with local time, i.e., the differences in foF2 are generally smaller at night and larger in noontime when equatorial ionization anomaly (EIA) is well developed.     

40CrNi2Si2MoVA钢喷丸强化层微观结构

喷丸强化在金属材料表面形成强化层,可以有效提高构件的疲劳寿命,是金属构件表面完整性制造的重要方法.喷丸强化已有效应用于40CrNi2Si2MoVA钢制构件,为了探明喷丸强化对该钢种的强化机理,本工作采用高分辨电子显微电镜(HREM)对40CrNi2Si2MoVA钢喷丸强化层微观组织结构进行了系统分析研究.结果表明:喷丸强化使40CrNi2Si2 MoVA钢组织细化,呈明显的马氏体“有效晶粒”现象,“有效晶粒”尺寸为几个纳米到几十个纳米;“有效晶粒”界面呈明显的倾转现象,相邻“有效晶粒”间转动角度为几度到几十度,最大达到30°.     

Al/Ni含能多层膜在Al2O3陶瓷/不锈钢焊接中的应用

采用磁控溅射设备,生长AuSn合金做焊料层、Al/Ni含能多层膜做热量提供层,实现了不锈钢和Al_2O_3间的异质材料自蔓延高温扩散焊。利用SEM、XRD和DSC等测试手段表征AuSn合金和Al/Ni含能多层膜的微观形貌、相成分和放热量;用万能试验机测试焊接接头的力学性能。结果表明,AuSn合金的质量比基本达到80∶20,而多层膜的层状结构清晰,反应热达到1 239 J/g。焊接实验结果表明,仅使用AuSn焊料时,剪切强度仅为46 MPa,在增加Al/Ni含能多层膜后,其剪切强度可达90 MPa,强度提高了约一倍。焊接接头的界面显微形貌和相结构研究表明,剪切强度的增强主要是Al/Ni多层膜提供了额外能量使得界面处的反应剧烈,陶瓷金属化层与中间层的反应加剧,形成了新的反应生成物。     

某型工程车多功能检测仪的硬件设计

设计的检测仪用于检测某型工程车的电控系统,以51单片机作为中央处理单元,以MAX392多路选择器实现多路选通,以CPLD扩展外围接口,可较好地实现信号的采集、存储和信息显示等功能。检测仪还具有代用功能,在紧急情况下可代替原车电控系统进行工作。     

基于遗传优化算法的微通道紫铜热交换器扩散连接工艺

基于遗传优化算法,进行了T2紫铜同种材料扩散连接工艺研究。采用正交试验方法,结合BP神经网络和多目标遗传算法,以扩散连接时的温度、压力、保温时间为输入变量,以扩散连接后的试样焊合率和变形量为输出变量,对扩散连接工艺参数进行优化,并实施相应的扩散连接验证试验。结果表明:T2紫铜合适的扩散连接工艺参数为:温度780℃、压力7. 5 MPa、保温时间120 min,此条件下焊合率可达95. 26%,变形量为0. 166 mm。采用此工艺参数进行微通道热交换器零件制造,厚度方向变形量0. 162 mm,经超声C扫描后连接情况良好,经耐压防漏检测后满足密封性及设计要求。     

SiO_2-C复合气凝胶的制备及其结构

以间苯二酚(R)和甲醛(F)为碳源,以3-胺丙基三乙氧基硅烷(APTES)为硅源,一步溶胶一凝胶法简单快捷地合成了SiO_2-RF复合气凝胶,高温碳化后得到SiO_2-C复合气凝胶,并用扫描电镜、比表面分析仪对所得样品的结构进行了研究,并讨论了不同投料比对气凝胶结构的影响.结果表明碳化前,投料比APTES/R=1时,所得气凝胶具有最大的比表面积(S_(BET)=606.1 m~2/g),碳化后,由于体积收缩和酚醛热解产生新孔隙双重因素的影响,投料比AFTES/R=1/2时样品的比表面积达到最大(S_(BET)=704.2 m~2/g).