The characteristics of sharp (small-scale) boundaries of solar wind plasma and magnetic field structures

We investigate properties of large (>20%) and sharp (<10 min) solar wind ion flux changes using INTERBALL-1 and WIND plasma and magnetic field measurements from 1996 to 1999. These ion flux changes are the boundaries of small-scale and middle-scale solar wind structures. We describe the behavior of the solar wind velocity, temperature and interplanetary magnetic field (IMF) during these sudden flux changes. Many of the largest ion flux changes occur during periods when the solar wind velocity is nearly constant, so these are mainly plasma density changes. The IMF magnitude and direction changes at these events can be either large or small. For about 55% of the ion flux changes, the sum of the thermal and magnetic pressure are in balance across the boundary. In many of the other cases, the thermal pressure change is significantly more than the magnetic pressure change. We also attempted to classify the types of discontinuities observed.     

低纬地磁Z分量的半年变化

利用武汉、广州、泉州和琼中等4个低纬地磁站连续多年的地磁资料，计算了各月5个磁静日Z分量日均值与中午1100---1300时段平均值之差(Dz)，对每年12个Dz采用多元回归分析方法，得到各年的半年变化幅度和相位．结果表明：4个站的Dz每年都有半年变化现象；半年变化幅度与太阳活动有关，一般来说，太阳活动高年Dz半年变化幅度明显大于太阳活动低年；太阳活动本身的半年变化，对Dz半年变化幅度有显著的调制作用；Dz半年变化的相位在3—4月(或9—10月)，即极大值出现在分季；低纬地区地磁Z分量存在显著的半年变化，能够反映赤道电急流也有明显的半年变化，这再一次证明，赤道电急流幅度的半年变化，通过“喷泉效应”使得电离层，f0F2产生半年变化，其是产生，f0F2半年变化的一个主要因素．     

神舟2号大气密度探测器的探测结果(Ⅰ)日照和阴影区域热层大气密度变化

选用了神舟2号（SZ-2）大气密度探测器在2001年2—4月间的探测数据,进行日照和阴影区域热层大气密度变化的探讨.结果表明:在高度410km附近,日照和阴影区域大气密度变幅为2—3倍,变幅的大小与地磁活动程度呈负相关关系.日照面大气密度峰区位于星下点地方时1400—1500LT的纬度处,峰值大小与太阳活动程度呈正相关关系.阴影面大气密度谷区位于星下点地方时0400-0500的纬度处,同时在±10°纬度区域中还出现了阴影面峰区.     

重现性地磁活动的数值预报

重现性地磁扰动作为地磁活动的重要部分，其特性在磁情预报中起着不可缺少的重要作用．本文利用地磁扰动在一定条件下具有２７天重现的特性和现代时序分析法中的自适应滤波方法，对北京地磁台Ｋ指数的预报方法进行了研究，并分别在太阳黑子活动低年和高年的两个时间段，进行了预报实验：低年时段预报结果精度为０．６６；在高年时段，预报精度为０．７９．进一步分析还表明，理论计算方法应当与多方面的物理分析相结合，这样才能为磁扰的定量分析和预报提供更充分与合理的计算条件和物理根据．     

一般硬化材料弹塑性旋转盘的变分解法

首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;再在体积不变条件下用弹性位移场的已知模态和一待定幅值构成弹塑性位移场;最后用势能原理确定该幅值而得到封闭解。     

研究用现场数据估计系统可靠性参数置信区间

研究用元部件现场信息估计系统可靠性参数,如系统可靠度、可靠寿命等区间估计问题。文中提出了一种新的估计方法——替换百分点法,并运用Monte Carlo数字仿真对估计的置信度和精度进行了分析,研究结果表明此方法具有工程应用价值。     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

AADL在航天器控制系统设计中的应用研究

以某型号航天器为例提出了一种使用体系结构分析和设计语言(AADL,architecture analysis & design language)分层次建模的方法,建立控制系统软件及软件与硬件之间的交互模型.采用状态自动机方式描述串口通信协议,以便分析模型.     

数字化技术在叶轮研制中的应用

本文通过分析归纳建立了一种叶轮数字化建模方法，并利用该方法成功实现了某型叶轮三维模型创建，同时也根据该数字化模型实现了模具数字化设计及其数控加工。