中国核电厂操作员反应时认知模型的应用(英文)

讨论了一些有关人员行为与时间有依赖关系的可靠性模型；给出了中国核电厂操作员在清华大学培训模型机上的一些可靠性实验结果。此外，还根据已获得的实验数据计算了在ＡＴＷＳ事故条件下人的失误概率。     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

飞机冲压空气涡轮系统的动态特性分析

冲压空气涡轮是飞机能源失效时使用的关键应急系统。首先依据冲击空气涡轮（RAT）工作原理确定其物理架构；然后对涡轮部件、能源转换装置、展开装置和展开随动机构等4个主要部件进行力学分析，建立各部件的力学方程组。依据该力学方程组，建立涉及力学、液压、刚体动力学的多学科冲压空气涡轮系统模型。使用该模型仿真了某真实系统在不同工况和设计参数下的动态特性，研究了关键设计参数对系统性能的影响，为冲压空气涡轮系统正向设计提供依据。最终，某型冲压空气涡轮系统风洞试验数据验证了所提系统模型的准确性。     

论承包经营企业的短期行为及其对策

本文针对承包经营企业中的短期行为问题,列举了它的表现形式并对其成因进行了分析,在此基础上,提出了若干现实对策。     

Near-wall topological patterns and flow structures over a simplified Danaus plexippus model

Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles. The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry (PIV) techniques. There are three near-wall topological patterns with different Angles of Attack (AoAs): the separation bubble, the Leading-Edge Vortex (LEV) and the high AoAs flow. For the separation bubble pattern, two saddles and two foci form in the middle of the model. The features of the LEV pattern are the leading-edge separation lines. The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex (WTV). For the high AoAs flow pattern, four unstable foci are found at the forewing and the hindwing respectively. The angle between the trajectory of the WTV and the model increases with increasing AoA even though the slope of the WTV angle versus AoA curve declines at the moderate AoAs.     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

Streamwise vortex generation by the rod

The technology development related to aerodynamics is leading to ever increasing loads of wings, airfoils and turbine and compressor blades. The increase in aerodynamic forces is often leading to flow separation and depreciation of the aerodynamic performance of flying objects or propulsion systems. Flow control methods are required to avoid these negative effects. In the recent two decades the flow control by means of air-jet vortex generators has been also intensively investigated. In this method a streamwise vortex is introduced by an oblique jet. The necessity to supply air by a pipe system may be considered a disadvantage. In order to eliminate this feature, it has been proposed to put out a rod instead of a jet. It has been shown that the application of a rod can introduce the same effect as a jet, as long as the streamwise vortex generation is concerned and appropriate dimensions are used. The present paper focuses on the influence of rod vortex generators on a flow pattern downstream. The results presented here concern experimental and numerical investigations and provide guidelines for the design of a new flow control method dedicated mainly to external flows.     

延伸冲击孔冲击冷却流动与换热特性的数值研究

采用数值模拟方法研究了延伸冲击孔冲击冷却系统的冷却特性,分析了3个冲击雷诺数和5个冲击孔延伸长度对冲击腔内流动与换热特性的影响,给出了靶面努塞尔数分布、靶面压力分布、中心截面流速与综合换热性能的变化。结果表明：延伸冲击孔可以有效地防止横流对冲击射流的偏转作用,同时使射流出口更加贴近冲击靶面壁面,冲击速度更高,可以明显提高靶面的换热系数,并使整个靶面上的换热系数分布也更加均匀。冲击冷却的冷却性能随着冲击孔延伸长度的增加而增加,相较于传统冲击冷却（baseline）,在L/d=2.5时靶面平均努塞尔数提升达15%以上,但压力损失也相对较高;对比不同延伸长度冲击孔的综合换热性能,发现存在最佳的L/d取值范围使冲击冷却系统获得最佳的综合冷却性能。在本研究范围内,最佳的L/d= 2.5。