减压直流非转移弧等离子体射流速度的静电探针测量

组建了一套利用静电探针诊断技术测量减压直流非转移弧等离子体射流速度的实验系统。对以纯氩为工质的等离子体,在气流量1．25×10^-1kg/s、弧电流80A、真空室压力165Pa的条件下,测量了射流的速度及其分布。结果表明射流在发生器出口处中心最高速度约为1200m／s,在半径20mm处减小到635m／s。沿射流轴线方向的速度梯度约为10（ms^-1）／mm。射流速度随着弧电流增加而缓慢单调增加;当真空室压力从165Pa提高到2kPa时,发生器出口轴线上的射流速度从1200m／s降至570m／s。     

大密度变化非连续介质气体流场的数值仿真

针对大密度变化非连续介质气体流场的仿真难题,实现了分区可变时间步长方法,为了保证宏观物理量通量在界面上连续,针对穿过两个时间步长不相等的区之间的界面的分子执行剩余时间缩放处理。提出了一种高效的分区界面和壁面处理算法,将每个界面设定为只属于一个区,将跨过多个区的壁面分解成分别只属于一个区的多个壁面,并规定仿真分子只能与本区的界面和壁面相互作用。对喷管流场的模拟表明,此方法可以大大提高计算效率。     

激光功率与底面状态对选区激光熔化球化的影响

为研究激光功率与底面状态对选区激光熔化熔池流动的影响,基于离散单元法建立了选区激光熔化铺粉模型,采用粒径分布与实验相符的马氏体时效钢粉末分别铺展到平坦底面和增材底面上,将计算获得的粉末分布导入到基于有限体积法建立的选区激光熔化熔池计算流体力学模型中,研究激光功率和基板底面粗糙度对熔池流动和熔道表面形貌的影响。采用激光单道扫描实验验证铺粉模型和选区激光熔化模型。结果表明：随着激光功率的降低,单位长度的球化数量增加;由于增材底面使熔池润湿性变差,同时又对熔池流动行为产生扰动,使得增材粗糙底面上熔道的球化数量增加。选区激光熔化铺粉模拟及激光单道扫描模拟结果与实验结果吻合较好。本研究可为选区激光熔化工艺中工艺参数的选择提供理论指导。     

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.      

不同温度和应力状态下Ni-Ti形状记忆合金力学行为分析

为了研究Ni-Ti形状记忆合金在不同应力状态下的力学行为,文中通过分离式Hopkinson杆实验装置分别对不同Ni-Ti形状记忆合金试样进行了动态拉伸和压缩试验。实验温度从291~573 K。从不同应力状态和试验温度的试验结果分析中发现:Ni-Ti形状记忆合金的相变屈服应力和位错屈服应力均随着试验温度的增加而增加;此外,同一Ni-Ti形状记忆合金压缩状态下的相变屈服应力和位错屈服应力均明显高于其拉伸状态下的相变屈服极限和位错屈服极限;而且对于同一Ni-Ti形状记忆合金,变形后材料的逆相变起始温度比变形前材料逆相变的起始温度高,且应变率越高,逆相变起始温度增加的越快。     

自动钻铆技术在波音737尾段项目中的应用

通过自动钻铆技术在波音737尾段中的应用,介绍了自动钻铆技术的特点及工艺.     

不同温度下TC21钛合金等离子表面渗Cr层的摩擦磨损性能

为提高TC21合金的摩擦磨损性能,采用双辉等离子冶金技术在TC21合金表面制备渗Cr改性层,利用扫描电镜(Scanning electron microscope,SEM),能谱仪(Energy dispersive spectromenter,EDS),显微硬度仪和划痕仪等研究了渗Cr层的组织形貌特征、硬度及结合强度,并 在20,300,500 ℃条件下使用摩擦磨损试验机对基体及渗Cr层的摩擦磨损性能进行对比、探究,并分析磨损机理。结果表明：渗Cr层厚度为30μm,均匀致密,与基体结合力至少能承受64 N的垂直载荷;改性层表面硬度超过1 000 HV0.1,约为基体的3倍;TC21合金渗Cr后,不同温度下的减摩性能和耐磨性能均得到提高。在室温下TC21基体磨损机理主要是磨粒磨损、粘着磨损和氧化磨损,而渗Cr层的磨损机理主要是磨粒磨损;500 ℃时基体粘着磨损和氧化磨损程度变得更加严重,渗Cr层磨损机理是剥层磨损和氧化磨损。      

Capillary flow rate limitation in asymmetry open channel

This paper focuses on the stability of capillary forced flow.In space,open capillary channels are widely used as the liquid and gas separation devices to manage liquid positioning and transportation.Surface collapse happens when the flow rate exceeds the critical value,leading to a failure of propellant management.Knowledge of flow rate limitation is of great significance in design and optimization of propellant management devices(PMDs).However,the capillary flow rate limitation in an asymmetry channel has not been studied yet in the literature.In this paper,by introducing an equivalent angle to convert the asymmetry corner to a symmetry one,the one-dimensional theoretical model is developed.The flow rate limitation can then be investigated as a function of the channel geometry as well as liquid property based on the model.Comparisons between the asymmetry and symmetry channels bring forth the characteristics of the two kinds of channels,and demonstrate good accordance between the new advanced model and the existing one in the literature.This theoretical model can provide valuable reference for PMD designers.     

流动显示的现状和发展

本文以第四届国际流动显示会议为主要内容,结合其它资料介绍流动显示的现状和发展。