密度变化时金属橡胶材料的非线性本构关系

以多孔材料理论为基础,干摩擦非线性理论为依据,并结合小曲梁模型建立金属橡胶材料的非线性本构关系,对空心圆柱形金属橡胶材料的静态试验结果进行拟合,得到非线性本构关系模型中的各项系数与密度的变化关系式,从而实现对该材料在密度发生变化情况下的本构关系的预估。     

Statistical analysis of the ionospheric ion density recorded by DEMETER in the epicenter areas of earthquakes as well as in their magnetically conjugate point areas

Results of a statistical variation of total ion density observed in the vicinity of epicenters as well as around magnetically conjugated points of earthquakes are presented in this paper. Two data sets are used: the ion density measured by DEMETER during about 6.5?years and the list of strong earthquakes (M_W?≥?4.8) occurring globally during this period (14,764 earthquakes in total). First of all, ionospheric perturbations with 23–120?s observation time corresponding to spatial scales of 160–840?km are automatically detected by a software (64,287 anomalies in total). Second, it is checked if a perturbation could be associated either with the epicenter of an earthquake or with its magnetically conjugated point (distance?<?1500?km and time?<?15?days before the earthquake). The index Kp?<?3 is also considered in order to reduce the effect of the geomagnetic activity on the ionosphere during this period. The results show that it is possible to detect variations of the ionospheric parameters above the epicenter areas as well as above their conjugated points. About one third of the earthquakes are detected with ionospheric influence on both sides of the Earth. There is a trend showing that the perturbation length increases as the magnitude of the detected EQs but it is more obvious for large magnitude. The probability that a perturbation appears is higher on the day of the earthquake and then gradually decreases when the time before the earthquake increases. The spatial distribution of perturbations shows that the probability of perturbations appearing southeast of the epicenter before an earthquake is a little bit higher and that there is an obvious trend because perturbations appear west of the conjugated point of an earthquake.     

低密度高亚声速引射风洞设计及性能研究

研究以火星表面大气条件和火星飞行器飞行速度为基础，设计一个低密度高亚声速引射风洞，并运用ANSYS FLUENT 15.0对多喷嘴引射风洞的性能进行了数值计算分析。首先对计算进行了网格无关性验证，在保证计算精度和减少时间与计算资源的基础上，通过研究发现：多喷嘴引射器作为风洞动力系统可满足试验段马赫数达到0.77的高亚声速马赫数要求，并且对试验段上下壁面采用各1°的扩张角可有效降低试验段边界层对压力的影响，从而使试验段静压基本维持不变；提高引射膨胀比是提高试验段雷诺数的一个有效措施，但是会降低引射系数，同时会增加试验段的静压梯度，影响试验段的气流品质。因此低密度引射风洞设计过程中必须综合考虑试验段扩张角，引射膨胀比等因素。     

卫星高功能密度综合电子系统设计

微小卫星综合电子系统承载了卫星大部分功能，是卫星任务处理和控制的中心，未来新的智能化应用、星群应用、通信服务等需求也将由卫星执行，对综合电子系统提出了新的要求。分析了国外典型小卫星综合电子系统，具有功能综合度高、多数功能集中在一台计算机中、卫星功能软件化的特点。设计了基于软件定义的综合电子系统一体化结构，硬件采用高度集成的模块化设计，软件采用分层和组件化设计，将系统功能进行分层，通过软件定义组件的方式实现各层功能和业务。高功能密度综合电子系统由一个通用化的高性能硬件平台和各种可加载的APP软件组成，除传统功能外，还可扩展自主任务管理、星间组网和载荷管理等功能，不仅使卫星的集成度和功能密度大幅提升，还能实现卫星功能重构，达到一星多用、一星多能的目的，有利于紧急时期卫星系统快速构建与应用，对于未来星座组网应用也具有一定意义。     

Comparison of Ionospheric Total Electron Content (TEC) over Sonmiani (Pakistan) with NeQuick-2 and IRI-2012 during July 2014 – June 2015

In this study, Total Electron Content (TEC) observations acquired by a GNSS receiver installed at Sonmiani (Geog. Coord. 25.19°N, 66.74°E, Geomag. Coord. 17.62°N, 141.5°E) are being reported for the first time. The data utilized is hourly instantaneous TEC values during 10 International Quiet Days (IQDs) per month from Jul-14 to Jun-15, totaling 120 observation days for monitoring nominal TEC. The findings confirm the semi-annual trend of TEC over Sonmiani, which lies at the northern crest of Equatorial Ionization Anomaly (EIA) region. The TEC measurements are then compared with NeQuick-2 and International Reference Ionosphere (IRI-2012) models. It was found that the TEC values derived from NeQuick-2 are in better agreement with GNSS measurements than those from IRI-2012. The TEC measurements also show seasonal variation which is largest during Equinox months. The TEC value in Dec solstice is higher than the Jun solstice, which confirms that the seasonal anomaly is playing a major role in this region during the course of study.     

一种新型铁电移相器材料的第一性原理计算

铁电薄膜移相器是基于铁电材料的新型移相器,被广泛应用于相控阵天线中。对于这类移相器组成材料的性能改进一直是雷达系统在军事、航天等领域的研究热点之一。基于第一性原理密度泛函理论,综合分析了ABi₂Nb₂O₉(A=Ba, Pb, Sr, Ca)材料的电子属性、化学键和极化属性。结果表明:这种体系有着类似的铁电性起源；Nb—O和Bi—O间的杂化对于系统的畸变和铁电相的稳定起着重要作用；随着A位离子半径的增大,体系的畸变参数也随之增大,导致材料有更大的自发极化,增强了铁电移相器的性能。实验结果验证了理论计算的正确性,为新型铁电移相器的研发奠定了基础。     

Numerical investigation of transitions in flow states and variation in aerodynamic forces for flow around square cylinders arranged inline

This study focuses on the transitions in flow states around two-, three- and four-inline square cylinders under the effect of Reynolds numbers at two different gap spacing values using the lattice Boltzmann method. For this purpose, Reynolds number is varied in the range 1–130 while two different values of spacing taken into account are gap spacing?=?2 and 5. Before going to actual problem, the code is tested for flow around a single square cylinder by comparing the results with experimental and numerical results of other researchers, and good agreement is found. The current numerical computations yield that for both spacing values and all combinations of cylinders there exist three different sates of flow depending on Reynolds numbers: steady state, transitional state and unsteady state. It is found that the range of Reynolds numbers for these flow states is different for both spacing values. At gap spacing?=?2 the range of Reynolds numbers for each flow state decreases by increasing the number of cylinders while at gap spacing?=?5 opposite trend is observed. The results also show that at gap spacing?=?2 the reduction in drag force is greater than the corresponding reduction at gap spacing?=?5. The maximum reduction in drag force is observed at Reynolds numbers?=?1 at both spacing values. Similarly, at both spacing values and all Reynolds numbers, the maximum reduction in drag force is observed for the case of four-inline square cylinders.     

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Electron beam melting (EBM), as an excellent Additive Manufacturing (AM) technology, enables the printing of Ti-6Al-4 V alloy for a wide range of applications such as aerospace and biomechanical industries. It improves functionality and integrity of components and negates complexities in assembly processes. However, due to the poor surface and sub-surface integrity represented by the rough surface finish and low dimensional accuracy, achieving a favorable surface condition is quite challenging. Therefore, post processing becomes essential for these electron beam melted (EBM-ed) Ti-6Al-4 V alloys. Being the most common technique to improve such parts, milling of Ti-6Al-4 V alloy is very challenging and resulting tool wear issues, due to its unique material properties. Thus, this paper presents a comprehensive study on the surface integrity of EBM-ed Ti-6Al-4 V parts processed by precision grinding and electropolishing, aiming to qualitatively and quantitatively clarify the interrelation between process parameters and processed surface quality. The surface and subsurface characteristics such as profile accuracy, surface roughness, microstructure, defective layer and residual stress before and after post processing were compared and evaluated. The results show that by precision grinding, the profile accuracy was improved from over 300 µm PV to 7 µm PV, while surface roughness (R_a) was reduced from 30 µm to about 2 µm. The layer with partially melt particles was removed, but introduced a deformed subsurface layer with more residual stress. Then by applying electropolishing, the residual stress was released and the deformed layer was removed. In addition, R_a was further reduced to 0.65 µm. The research can serve as a reference for the integration of post machining processes with AM.     

基于随机模糊参数的结构模糊可靠性分析模型

结构模糊可靠性理论研究主要是建立仅考虑失效准则模糊性的结构模糊可靠性分析模型.在现有结构模糊可靠性分析理论研究的基础上,同时考虑工程中结构参数的随机性和区间模糊性,提出了模糊概率密度函数的概念,并推导相应的模糊概率密度函数公式,给出了反映随机参数区间模糊性的隶属函数的类型和选取方法.建立了同时考虑随机参数区间模糊性和失效准则模糊性的结构模糊可靠性分析模型.讨论了模糊可靠性分析模型与常规的随机可靠性分析模型的相容性.并给出算例进行验证,研究结果表明,采用该结构模糊可靠性分析方法更能全面地利用结构参数信息.